3275 |
kaklik |
1 |
#include "main.h" |
|
|
2 |
|
|
|
3 |
#define LCD_ENABLE_PIN PIN_E0 //// |
|
|
4 |
#define LCD_RS_PIN PIN_E1 //// |
|
|
5 |
#define LCD_RW_PIN PIN_E2 //// |
|
|
6 |
#define LCD_DATA4 PIN_D4 //// |
|
|
7 |
#define LCD_DATA5 PIN_D5 //// |
|
|
8 |
#define LCD_DATA6 PIN_D6 //// |
|
|
9 |
#define LCD_DATA7 PIN_D7 |
|
|
10 |
#include <lcd.c> |
|
|
11 |
|
|
|
12 |
#include "../SHT25.h" |
|
|
13 |
#include "../LTS01.h" |
3283 |
kakl |
14 |
#include "./HMC5883L.h" |
|
|
15 |
#include <math.h> |
3275 |
kaklik |
16 |
|
3286 |
kaklik |
17 |
#define MPL3115_ADDR_R 0xC1 //addresa pro cteni |
|
|
18 |
#define MPL3115_ADDR_W 0xC0 |
3283 |
kakl |
19 |
|
3286 |
kaklik |
20 |
#include "../MPL3115.h" |
|
|
21 |
|
|
|
22 |
|
3275 |
kaklik |
23 |
void main() |
|
|
24 |
{ |
3286 |
kaklik |
25 |
float temp1, temp2, temp3, humidity, preasure; |
3275 |
kaklik |
26 |
int16 i=0; |
|
|
27 |
|
|
|
28 |
setup_adc_ports(NO_ANALOGS|VSS_VDD); |
|
|
29 |
setup_adc(ADC_CLOCK_DIV_2); |
|
|
30 |
setup_spi(SPI_SS_DISABLED); |
|
|
31 |
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
|
|
32 |
setup_timer_1(T1_DISABLED); |
|
|
33 |
setup_timer_2(T2_DISABLED,0,1); |
|
|
34 |
setup_ccp1(CCP_OFF); |
|
|
35 |
setup_comparator(NC_NC_NC_NC); // This device COMP currently not supported by the PICWizard |
|
|
36 |
setup_oscillator(OSC_8MHZ); |
|
|
37 |
|
|
|
38 |
|
3283 |
kakl |
39 |
printf("GeoMet01A\r\n"); |
3275 |
kaklik |
40 |
printf("(c) Kaklik 2013\r\n"); |
|
|
41 |
printf("www.mlab.cz\r\n"); |
3283 |
kakl |
42 |
|
|
|
43 |
// Init the HMC5883L. Set Mode register for |
|
|
44 |
// continuous measurements. |
|
|
45 |
hmc5883l_write_reg(HMC5883L_CFG_A_REG, 0x18); // no average, maximal update range |
|
|
46 |
hmc5883l_write_reg(HMC5883L_CFG_B_REG, 0x00); // minimal range |
|
|
47 |
hmc5883l_write_reg(HMC5883L_MODE_REG, 0x00); |
3275 |
kaklik |
48 |
|
|
|
49 |
lcd_init(); |
|
|
50 |
lcd_putc("(c) Kaklik 2013"); |
|
|
51 |
lcd_gotoxy(3,2); |
|
|
52 |
lcd_putc("www.mlab.cz"); |
|
|
53 |
Delay_ms(2000); |
|
|
54 |
lcd_init(); |
|
|
55 |
|
|
|
56 |
while (TRUE) |
|
|
57 |
{ |
|
|
58 |
lcd_gotoxy(1,1); |
|
|
59 |
temp1 = SHT25_get_temp(); |
|
|
60 |
humidity = SHT25_get_hum(); |
|
|
61 |
temp2= LTS01_get_temp(); |
3283 |
kakl |
62 |
hmc5883l_read_data(); |
3286 |
kaklik |
63 |
|
|
|
64 |
temp3=mpl3115_T(); |
|
|
65 |
preasure=mpl3115_P(); |
|
|
66 |
mpl3115_setP(); //nastaveni pro tlak a teplotu |
|
|
67 |
|
|
|
68 |
printf(lcd_putc,"%2.2f%cC %2.2f\%%",temp1, 0xb2, humidity); |
3275 |
kaklik |
69 |
lcd_gotoxy(1,2); |
3286 |
kaklik |
70 |
printf(lcd_putc,"%2.2f%cC %6.0fPa ",temp2, 0xb2, preasure); |
|
|
71 |
|
|
|
72 |
printf("%ld %f %f %f %6.2f %3.2f %Ld %Ld %Ld \n\r",i, temp1, humidity, temp2, preasure, temp3, compass.x, compass.y, compass.z); |
3275 |
kaklik |
73 |
i++; |
3286 |
kaklik |
74 |
|
3275 |
kaklik |
75 |
Delay_ms(100); |
|
|
76 |
} |
|
|
77 |
|
|
|
78 |
} |