Rev Author Line No. Line
4826 kaklik 1 # generated by Slic3r 1.2.9 on Fri Jul 31 14:56:23 2015
2  
3 [filament:ABS_1.75]
4 bed_temperature = 90
5 bridge_fan_speed = 0
6 cooling = 1
7 disable_fan_first_layers = 0
8 extrusion_multiplier = 1.01
9 fan_always_on = 0
10 fan_below_layer_time = 1
11 filament_diameter = 1.75
12 first_layer_bed_temperature = 90
13 first_layer_temperature = 225
14 max_fan_speed = 0
15 min_fan_speed = 0
16 min_print_speed = 15
17 slowdown_below_layer_time = 20
18 temperature = 225
19  
20 [filament:ABS_1.75 3D factories]
21 bed_temperature = 90
22 bridge_fan_speed = 0
23 cooling = 1
24 disable_fan_first_layers = 0
25 extrusion_multiplier = 1
26 fan_always_on = 0
27 fan_below_layer_time = 5
28 filament_diameter = 1.75
29 first_layer_bed_temperature = 90
30 first_layer_temperature = 225
31 max_fan_speed = 100
32 min_fan_speed = 50
33 min_print_speed = 15
34 slowdown_below_layer_time = 20
35 temperature = 225
36  
37 [filament:ABS_1.75 red 3D factories]
38 bed_temperature = 90
39 bridge_fan_speed = 0
40 cooling = 1
41 disable_fan_first_layers = 0
42 extrusion_multiplier = 1
43 fan_always_on = 0
44 fan_below_layer_time = 5
45 filament_diameter = 1.73
46 first_layer_bed_temperature = 80
47 first_layer_temperature = 230
48 max_fan_speed = 60
49 min_fan_speed = 0
50 min_print_speed = 15
51 slowdown_below_layer_time = 20
52 temperature = 225
53  
54 [filament:PLA_1.75]
55 bed_temperature = 50
56 bridge_fan_speed = 100
57 cooling = 1
58 disable_fan_first_layers = 1
59 extrusion_multiplier = 1
60 fan_always_on = 1
61 fan_below_layer_time = 1
62 filament_diameter = 1.74
63 first_layer_bed_temperature = 60
64 first_layer_temperature = 215
65 max_fan_speed = 100
66 min_fan_speed = 100
67 min_print_speed = 15
68 slowdown_below_layer_time = 20
69 temperature = 210
70  
71 [filament:PLA_1.75 3D factories]
72 bed_temperature = 50
73 bridge_fan_speed = 50
74 cooling = 1
75 disable_fan_first_layers = 0
76 extrusion_multiplier = 0.9524
77 fan_always_on = 1
78 fan_below_layer_time = 60
79 filament_diameter = 1.75
80 first_layer_bed_temperature = 60
81 first_layer_temperature = 185
82 max_fan_speed = 100
83 min_fan_speed = 100
84 min_print_speed = 10
85 slowdown_below_layer_time = 30
86 temperature = 185
87  
88 [filament:PLA_1.75 _Mladec_green]
89 bed_temperature = 50
90 bridge_fan_speed = 100
91 cooling = 1
92 disable_fan_first_layers = 1
93 extrusion_multiplier = 1
94 fan_always_on = 1
95 fan_below_layer_time = 60
96 filament_diameter = 1.75
97 first_layer_bed_temperature = 60
98 first_layer_temperature = 210
99 max_fan_speed = 100
100 min_fan_speed = 100
101 min_print_speed = 10
102 slowdown_below_layer_time = 30
103 temperature = 210
104  
105 [filament:Simple Mode]
106 bed_temperature = 110
107 extrusion_multiplier = 1
108 filament_diameter = 1.75
109 first_layer_bed_temperature = 115
110 first_layer_temperature = 235
111 temperature = 230
112  
113 [filament:config]
114 bed_temperature = 50
115 bridge_fan_speed = 100
116 cooling = 1
117 disable_fan_first_layers = 1
118 extrusion_multiplier = 1
119 fan_always_on = 1
120 fan_below_layer_time = 60
121 filament_diameter = 1.75
122 first_layer_bed_temperature = 60
123 first_layer_temperature = 212
124 max_fan_speed = 100
125 min_fan_speed = 100
126 min_print_speed = 10
127 slowdown_below_layer_time = 30
128 temperature = 212
129  
130 [filament:slic3r_config]
131 bed_temperature = 90
132 bridge_fan_speed = 0
133 cooling = 1
134 disable_fan_first_layers = 0
135 extrusion_multiplier = 0.95
136 fan_always_on = 0
137 fan_below_layer_time = 5
138 filament_diameter = 1.75
139 first_layer_bed_temperature = 80
140 first_layer_temperature = 230
141 max_fan_speed = 100
142 min_fan_speed = 50
143 min_print_speed = 15
144 slowdown_below_layer_time = 20
145 temperature = 230
146  
147 [presets]
148 filament = pad_config.ini
149 print = pad_config.ini
150 printer = pad_config.ini
151  
152 [print:0.2 layer]
153 avoid_crossing_perimeters = 0
154 bottom_solid_layers = 3
155 bridge_acceleration = 1000
156 bridge_flow_ratio = 1
157 bridge_speed = 15
158 brim_width = 10
159 complete_objects = 0
160 default_acceleration = 500
161 dont_support_bridges = 1
162 external_fill_pattern = rectilinear
163 external_perimeter_extrusion_width = 0
164 external_perimeter_speed = 90%
165 external_perimeters_first = 0
166 extra_perimeters = 1
167 extruder_clearance_height = 20
168 extruder_clearance_radius = 20
169 extrusion_width = 0
170 fill_angle = 45
171 fill_density = 15%
172 fill_pattern = honeycomb
173 first_layer_acceleration = 500
174 first_layer_extrusion_width = 200%
175 first_layer_height = 0.3
176 first_layer_speed = 60%
177 gap_fill_speed = 20
178 gcode_comments = 0
179 infill_acceleration = 500
180 infill_every_layers = 1
181 infill_extruder = 1
182 infill_extrusion_width = 0
183 infill_first = 0
184 infill_only_where_needed = 0
185 infill_overlap = 15%
186 infill_speed = 60
187 interface_shells = 0
188 layer_height = 0.2
189 min_skirt_length = 0
190 notes =
191 only_retract_when_crossing_perimeters = 1
192 ooze_prevention = 0
193 output_filename_format = [input_filename_base].gcode
194 overhangs = 1
195 perimeter_acceleration = 500
196 perimeter_extruder = 1
197 perimeter_extrusion_width = 0
198 perimeter_speed = 45
199 perimeters = 1
200 post_process =
201 raft_layers = 0
202 resolution = 0
203 seam_position = aligned
204 skirt_distance = 4
205 skirt_height = 1
206 skirts = 1
207 small_perimeter_speed = 30
208 solid_infill_below_area = 70
209 solid_infill_every_layers = 0
210 solid_infill_extruder = 1
211 solid_infill_extrusion_width = 0
212 solid_infill_speed = 55
213 spiral_vase = 0
214 standby_temperature_delta = -5
215 support_material = 0
216 support_material_angle = 0
217 support_material_contact_distance = 0.2
218 support_material_enforce_layers = 0
219 support_material_extruder = 1
220 support_material_extrusion_width = 0
221 support_material_interface_extruder = 1
222 support_material_interface_layers = 0
223 support_material_interface_spacing = 0
224 support_material_interface_speed = 100%
225 support_material_pattern = rectilinear
226 support_material_spacing = 2.5
227 support_material_speed = 60
228 support_material_threshold = 0
229 thin_walls = 1
230 threads = 2
231 top_infill_extrusion_width = 0
232 top_solid_infill_speed = 50
233 top_solid_layers = 3
234 travel_speed = 130
235 xy_size_compensation = 0
236  
237 [print:0.3 layer]
238 avoid_crossing_perimeters = 0
239 bottom_solid_layers = 3
240 bridge_acceleration = 1000
241 bridge_flow_ratio = 1
242 bridge_speed = 10
243 brim_width = 2
244 complete_objects = 1
245 default_acceleration = 500
246 dont_support_bridges = 1
247 external_fill_pattern = rectilinear
248 external_perimeter_extrusion_width = 0
249 external_perimeter_speed = 90%
250 external_perimeters_first = 0
251 extra_perimeters = 1
252 extruder_clearance_height = 20
253 extruder_clearance_radius = 20
254 extrusion_width = 0
255 fill_angle = 45
256 fill_density = 50%
257 fill_pattern = rectilinear
258 first_layer_acceleration = 500
259 first_layer_extrusion_width = 180%
260 first_layer_height = 0.3
261 first_layer_speed = 60%
262 gap_fill_speed = 20
263 gcode_comments = 0
264 infill_acceleration = 500
265 infill_every_layers = 1
266 infill_extruder = 1
267 infill_extrusion_width = 0
268 infill_first = 0
269 infill_only_where_needed = 0
270 infill_overlap = 15%
271 infill_speed = 60
272 interface_shells = 0
273 layer_height = 0.3
274 min_skirt_length = 0
275 notes =
276 only_retract_when_crossing_perimeters = 1
277 ooze_prevention = 0
278 output_filename_format = [input_filename_base].gcode
279 overhangs = 1
280 perimeter_acceleration = 500
281 perimeter_extruder = 1
282 perimeter_extrusion_width = 0
283 perimeter_speed = 45
284 perimeters = 3
285 post_process =
286 raft_layers = 0
287 resolution = 0
288 seam_position = aligned
289 skirt_distance = 10
290 skirt_height = 1
291 skirts = 1
292 small_perimeter_speed = 30
293 solid_infill_below_area = 70
294 solid_infill_every_layers = 0
295 solid_infill_extruder = 1
296 solid_infill_extrusion_width = 0
297 solid_infill_speed = 55
298 spiral_vase = 0
299 standby_temperature_delta = -5
300 support_material = 0
301 support_material_angle = 0
302 support_material_contact_distance = 0.2
303 support_material_enforce_layers = 0
304 support_material_extruder = 1
305 support_material_extrusion_width = 0
306 support_material_interface_extruder = 1
307 support_material_interface_layers = 0
308 support_material_interface_spacing = 0
309 support_material_interface_speed = 100%
310 support_material_pattern = rectilinear
311 support_material_spacing = 2.5
312 support_material_speed = 60
313 support_material_threshold = 0
314 thin_walls = 1
315 threads = 4
316 top_infill_extrusion_width = 0
317 top_solid_infill_speed = 50
318 top_solid_layers = 3
319 travel_speed = 130
320 xy_size_compensation = 0
321  
322 [print:0.3 layer brim]
323 avoid_crossing_perimeters = 0
324 bottom_solid_layers = 3
325 bridge_acceleration = 3000
326 bridge_flow_ratio = 1
327 bridge_speed = 10
328 brim_width = 10
329 complete_objects = 0
330 default_acceleration = 4000
331 dont_support_bridges = 1
332 external_fill_pattern = rectilinear
333 external_perimeter_extrusion_width = 0
334 external_perimeter_speed = 90%
335 external_perimeters_first = 0
336 extra_perimeters = 1
337 extruder_clearance_height = 20
338 extruder_clearance_radius = 20
339 extrusion_width = 0.6
340 fill_angle = 45
341 fill_density = 25%
342 fill_pattern = line
343 first_layer_acceleration = 0
344 first_layer_extrusion_width = 180%
345 first_layer_height = 0.3
346 first_layer_speed = 60%
347 gap_fill_speed = 20
348 gcode_comments = 0
349 infill_acceleration = 0
350 infill_every_layers = 1
351 infill_extruder = 1
352 infill_extrusion_width = 0
353 infill_first = 0
354 infill_only_where_needed = 0
355 infill_speed = 60
356 interface_shells = 0
357 layer_height = 0.3
358 min_skirt_length = 0
359 notes =
360 only_retract_when_crossing_perimeters = 1
361 ooze_prevention = 0
362 output_filename_format = [input_filename_base].gcode
363 overhangs = 1
364 perimeter_acceleration = 0
365 perimeter_extruder = 1
366 perimeter_extrusion_width = 0
367 perimeter_speed = 45
368 perimeters = 2
369 post_process =
370 raft_layers = 0
371 resolution = 0
372 seam_position = aligned
373 skirt_distance = 15
374 skirt_height = 1
375 skirts = 1
376 small_perimeter_speed = 30
377 solid_infill_below_area = 70
378 solid_infill_every_layers = 0
379 solid_infill_extruder = 1
380 solid_infill_extrusion_width = 0
381 solid_infill_speed = 55
382 spiral_vase = 0
383 standby_temperature_delta = -5
384 support_material = 0
385 support_material_angle = 0
386 support_material_enforce_layers = 0
387 support_material_extruder = 1
388 support_material_extrusion_width = 0
389 support_material_interface_extruder = 1
390 support_material_interface_layers = 0
391 support_material_interface_spacing = 0
392 support_material_interface_speed = 100%
393 support_material_pattern = rectilinear
394 support_material_spacing = 2.5
395 support_material_speed = 60
396 support_material_threshold = 0
397 thin_walls = 1
398 threads = 4
399 top_infill_extrusion_width = 0
400 top_solid_infill_speed = 50
401 top_solid_layers = 3
402 travel_speed = 130
403 xy_size_compensation = 0
404  
405 [print:ABS 1.75]
406 avoid_crossing_perimeters = 0
407 bottom_solid_layers = 3
408 bridge_acceleration = 0
409 bridge_flow_ratio = 1.9
410 bridge_speed = 60
411 brim_width = 0
412 complete_objects = 0
413 default_acceleration = 0
414 dont_support_bridges = 1
415 external_fill_pattern = rectilinear
416 external_perimeter_speed = 70%
417 external_perimeters_first = 0
418 extra_perimeters = 1
419 extruder_clearance_height = 20
420 extruder_clearance_radius = 20
421 extrusion_width = 0
422 fill_angle = 45
423 fill_density = 40%
424 fill_pattern = honeycomb
425 first_layer_acceleration = 0
426 first_layer_extrusion_width = 200%
427 first_layer_height = 0.3
428 first_layer_speed = 30%
429 gap_fill_speed = 20
430 gcode_comments = 0
431 infill_acceleration = 0
432 infill_every_layers = 1
433 infill_extruder = 1
434 infill_extrusion_width = 0
435 infill_first = 0
436 infill_only_where_needed = 0
437 infill_speed = 60
438 interface_shells = 0
439 layer_height = 0.2
440 min_skirt_length = 0
441 notes =
442 only_retract_when_crossing_perimeters = 1
443 ooze_prevention = 0
444 output_filename_format = [input_filename_base].gcode
445 overhangs = 1
446 perimeter_acceleration = 0
447 perimeter_extruder = 1
448 perimeter_extrusion_width = 0
449 perimeter_speed = 30
450 perimeters = 3
451 post_process =
452 raft_layers = 0
453 resolution = 0
454 seam_position = aligned
455 skirt_distance = 6
456 skirt_height = 1
457 skirts = 1
458 small_perimeter_speed = 30
459 solid_infill_below_area = 70
460 solid_infill_every_layers = 0
461 solid_infill_extrusion_width = 0
462 solid_infill_speed = 60
463 spiral_vase = 0
464 standby_temperature_delta = -5
465 support_material = 0
466 support_material_angle = 0
467 support_material_enforce_layers = 0
468 support_material_extruder = 1
469 support_material_extrusion_width = 0
470 support_material_interface_extruder = 1
471 support_material_interface_layers = 3
472 support_material_interface_spacing = 0
473 support_material_interface_speed = 100%
474 support_material_pattern = pillars
475 support_material_spacing = 2.5
476 support_material_speed = 60
477 support_material_threshold = 0
478 thin_walls = 1
479 threads = 2
480 top_infill_extrusion_width = 0
481 top_solid_infill_speed = 50
482 top_solid_layers = 3
483 travel_speed = 130
484  
485 [print:ABS_rocket]
486 avoid_crossing_perimeters = 0
487 bottom_solid_layers = 3
488 bridge_acceleration = 500
489 bridge_flow_ratio = 1.9
490 bridge_speed = 60
491 brim_width = 15
492 complete_objects = 0
493 default_acceleration = 1000
494 dont_support_bridges = 1
495 external_fill_pattern = rectilinear
496 external_perimeter_extrusion_width = 0
497 external_perimeter_speed = 70%
498 external_perimeters_first = 0
499 extra_perimeters = 1
500 extruder_clearance_height = 20
501 extruder_clearance_radius = 20
502 extrusion_width = 0.5
503 fill_angle = 45
504 fill_density = 40%
505 fill_pattern = honeycomb
506 first_layer_acceleration = 500
507 first_layer_extrusion_width = 200%
508 first_layer_height = 0.3
509 first_layer_speed = 30%
510 gap_fill_speed = 20
511 gcode_comments = 0
512 infill_acceleration = 500
513 infill_every_layers = 1
514 infill_extruder = 1
515 infill_extrusion_width = 0.4
516 infill_first = 0
517 infill_only_where_needed = 0
518 infill_speed = 60
519 interface_shells = 0
520 layer_height = 0.3
521 min_skirt_length = 0
522 notes =
523 only_retract_when_crossing_perimeters = 1
524 ooze_prevention = 0
525 output_filename_format = [input_filename_base].gcode
526 overhangs = 1
527 perimeter_acceleration = 500
528 perimeter_extruder = 1
529 perimeter_extrusion_width = 0
530 perimeter_speed = 30
531 perimeters = 3
532 post_process =
533 raft_layers = 0
534 resolution = 0
535 seam_position = aligned
536 skirt_distance = 6
537 skirt_height = 1
538 skirts = 1
539 small_perimeter_speed = 30
540 solid_infill_below_area = 70
541 solid_infill_every_layers = 0
542 solid_infill_extruder = 1
543 solid_infill_extrusion_width = 0
544 solid_infill_speed = 60
545 spiral_vase = 0
546 standby_temperature_delta = -5
547 support_material = 0
548 support_material_angle = 0
549 support_material_contact_distance = 0.2
550 support_material_enforce_layers = 0
551 support_material_extruder = 1
552 support_material_extrusion_width = 0
553 support_material_interface_extruder = 1
554 support_material_interface_layers = 3
555 support_material_interface_spacing = 0
556 support_material_interface_speed = 100%
557 support_material_pattern = pillars
558 support_material_spacing = 2.5
559 support_material_speed = 60
560 support_material_threshold = 0
561 thin_walls = 1
562 threads = 2
563 top_infill_extrusion_width = 0
564 top_solid_infill_speed = 50
565 top_solid_layers = 3
566 travel_speed = 130
567 xy_size_compensation = 0
568  
569 [print:ABS_vase]
570 avoid_crossing_perimeters = 0
571 bottom_solid_layers = 3
572 bridge_acceleration = 500
573 bridge_flow_ratio = 1.9
574 bridge_speed = 60
575 brim_width = 5
576 complete_objects = 0
577 default_acceleration = 1000
578 dont_support_bridges = 1
579 external_fill_pattern = rectilinear
580 external_perimeter_extrusion_width = 0
581 external_perimeter_speed = 70%
582 external_perimeters_first = 0
583 extra_perimeters = 1
584 extruder_clearance_height = 20
585 extruder_clearance_radius = 20
586 extrusion_width = 0
587 fill_angle = 45
588 fill_density = 0%
589 fill_pattern = honeycomb
590 first_layer_acceleration = 500
591 first_layer_extrusion_width = 120%
592 first_layer_height = 0.3
593 first_layer_speed = 30%
594 gap_fill_speed = 20
595 gcode_comments = 0
596 infill_acceleration = 500
597 infill_every_layers = 1
598 infill_extruder = 1
599 infill_extrusion_width = 0
600 infill_first = 0
601 infill_only_where_needed = 0
602 infill_speed = 60
603 interface_shells = 0
604 layer_height = 0.3
605 min_skirt_length = 0
606 notes =
607 only_retract_when_crossing_perimeters = 1
608 ooze_prevention = 0
609 output_filename_format = [input_filename_base].gcode
610 overhangs = 1
611 perimeter_acceleration = 500
612 perimeter_extruder = 1
613 perimeter_extrusion_width = 0
614 perimeter_speed = 30
615 perimeters = 1
616 post_process =
617 raft_layers = 0
618 resolution = 0
619 seam_position = aligned
620 skirt_distance = 6
621 skirt_height = 1
622 skirts = 1
623 small_perimeter_speed = 30
624 solid_infill_below_area = 70
625 solid_infill_every_layers = 0
626 solid_infill_extruder = 1
627 solid_infill_extrusion_width = 0
628 solid_infill_speed = 60
629 spiral_vase = 1
630 standby_temperature_delta = -5
631 support_material = 0
632 support_material_angle = 0
633 support_material_contact_distance = 0.2
634 support_material_enforce_layers = 0
635 support_material_extruder = 1
636 support_material_extrusion_width = 0
637 support_material_interface_extruder = 1
638 support_material_interface_layers = 3
639 support_material_interface_spacing = 0
640 support_material_interface_speed = 100%
641 support_material_pattern = pillars
642 support_material_spacing = 2.5
643 support_material_speed = 60
644 support_material_threshold = 0
645 thin_walls = 1
646 threads = 2
647 top_infill_extrusion_width = 0
648 top_solid_infill_speed = 50
649 top_solid_layers = 0
650 travel_speed = 130
651 xy_size_compensation = 0
652  
653 [print:Bridge]
654 avoid_crossing_perimeters = 0
655 bottom_solid_layers = 3
656 bridge_acceleration = 3000
657 bridge_flow_ratio = 1
658 bridge_speed = 10
659 brim_width = 5
660 complete_objects = 0
661 default_acceleration = 4000
662 dont_support_bridges = 1
663 external_fill_pattern = rectilinear
664 external_perimeter_speed = 90%
665 external_perimeters_first = 0
666 extra_perimeters = 1
667 extruder_clearance_height = 20
668 extruder_clearance_radius = 20
669 extrusion_width = 0.6
670 fill_angle = 45
671 fill_density = 25%
672 fill_pattern = line
673 first_layer_acceleration = 0
674 first_layer_extrusion_width = 125%
675 first_layer_height = 0.3
676 first_layer_speed = 60%
677 gap_fill_speed = 20
678 gcode_comments = 0
679 infill_acceleration = 0
680 infill_every_layers = 1
681 infill_extruder = 1
682 infill_extrusion_width = 0
683 infill_first = 0
684 infill_only_where_needed = 0
685 infill_speed = 60
686 interface_shells = 0
687 layer_height = 0.3
688 min_skirt_length = 0
689 notes =
690 only_retract_when_crossing_perimeters = 1
691 ooze_prevention = 0
692 output_filename_format = [input_filename_base].gcode
693 overhangs = 1
694 perimeter_acceleration = 0
695 perimeter_extruder = 1
696 perimeter_extrusion_width = 0
697 perimeter_speed = 45
698 perimeters = 2
699 post_process =
700 raft_layers = 0
701 resolution = 0
702 seam_position = random
703 skirt_distance = 10
704 skirt_height = 1
705 skirts = 1
706 small_perimeter_speed = 30
707 solid_infill_below_area = 70
708 solid_infill_every_layers = 0
709 solid_infill_extrusion_width = 0
710 solid_infill_speed = 55
711 spiral_vase = 0
712 standby_temperature_delta = -5
713 support_material = 0
714 support_material_angle = 0
715 support_material_enforce_layers = 0
716 support_material_extruder = 1
717 support_material_extrusion_width = 0
718 support_material_interface_extruder = 1
719 support_material_interface_layers = 0
720 support_material_interface_spacing = 0
721 support_material_interface_speed = 100%
722 support_material_pattern = rectilinear
723 support_material_spacing = 2.5
724 support_material_speed = 60
725 support_material_threshold = 0
726 thin_walls = 1
727 threads = 4
728 top_infill_extrusion_width = 0
729 top_solid_infill_speed = 50
730 top_solid_layers = 3
731 travel_speed = 100
732  
733 [print:Simple Mode]
734 bottom_solid_layers = 3
735 brim_width = 0
736 complete_objects = 0
737 extruder_clearance_height = 20
738 extruder_clearance_radius = 20
739 fill_density = 40%
740 fill_pattern = honeycomb
741 infill_speed = 60
742 layer_height = 0.2
743 perimeter_speed = 30
744 perimeters = 3
745 raft_layers = 0
746 support_material = 0
747 support_material_spacing = 2.5
748 top_solid_layers = 3
749 travel_speed = 130
750  
751 [print:Standard]
752 avoid_crossing_perimeters = 0
753 bottom_solid_layers = 3
754 bridge_acceleration = 0
755 bridge_flow_ratio = 1
756 bridge_speed = 20
757 brim_width = 0
758 complete_objects = 0
759 default_acceleration = 0
760 dont_support_bridges = 1
761 external_fill_pattern = rectilinear
762 external_perimeter_speed = 90%
763 external_perimeters_first = 0
764 extra_perimeters = 0
765 extruder_clearance_height = 20
766 extruder_clearance_radius = 20
767 extrusion_width = 0.6
768 fill_angle = 45
769 fill_density = 25%
770 fill_pattern = line
771 first_layer_acceleration = 0
772 first_layer_extrusion_width = 200%
773 first_layer_height = 0.3
774 first_layer_speed = 60%
775 gap_fill_speed = 20
776 gcode_comments = 0
777 infill_acceleration = 0
778 infill_every_layers = 1
779 infill_extruder = 1
780 infill_extrusion_width = 0
781 infill_first = 0
782 infill_only_where_needed = 0
783 infill_speed = 60
784 interface_shells = 0
785 layer_height = 0.3
786 min_skirt_length = 0
787 notes =
788 only_retract_when_crossing_perimeters = 1
789 ooze_prevention = 0
790 output_filename_format = [input_filename_base].gcode
791 overhangs = 1
792 perimeter_acceleration = 0
793 perimeter_extruder = 1
794 perimeter_extrusion_width = 0
795 perimeter_speed = 45
796 perimeters = 2
797 post_process =
798 raft_layers = 0
799 resolution = 0
800 seam_position = aligned
801 skirt_distance = 4
802 skirt_height = 1
803 skirts = 1
804 small_perimeter_speed = 30
805 solid_infill_below_area = 70
806 solid_infill_every_layers = 0
807 solid_infill_extrusion_width = 0
808 solid_infill_speed = 55
809 spiral_vase = 0
810 standby_temperature_delta = -5
811 support_material = 0
812 support_material_angle = 0
813 support_material_enforce_layers = 0
814 support_material_extruder = 1
815 support_material_extrusion_width = 0
816 support_material_interface_extruder = 1
817 support_material_interface_layers = 0
818 support_material_interface_spacing = 0
819 support_material_interface_speed = 100%
820 support_material_pattern = rectilinear
821 support_material_spacing = 2.5
822 support_material_speed = 60
823 support_material_threshold = 0
824 thin_walls = 1
825 threads = 2
826 top_infill_extrusion_width = 0
827 top_solid_infill_speed = 50
828 top_solid_layers = 3
829 travel_speed = 130
830  
831 [print:Weather_screen]
832 avoid_crossing_perimeters = 0
833 bottom_solid_layers = 3
834 bridge_acceleration = 3000
835 bridge_flow_ratio = 1
836 bridge_speed = 10
837 brim_width = 5
838 complete_objects = 0
839 default_acceleration = 4000
840 dont_support_bridges = 1
841 external_fill_pattern = concentric
842 external_perimeter_speed = 90%
843 external_perimeters_first = 0
844 extra_perimeters = 1
845 extruder_clearance_height = 20
846 extruder_clearance_radius = 20
847 extrusion_width = 0.6
848 fill_angle = 45
849 fill_density = 90%
850 fill_pattern = concentric
851 first_layer_acceleration = 0
852 first_layer_extrusion_width = 200%
853 first_layer_height = 0.3
854 first_layer_speed = 60%
855 gap_fill_speed = 20
856 gcode_comments = 0
857 infill_acceleration = 0
858 infill_every_layers = 1
859 infill_extruder = 1
860 infill_extrusion_width = 0
861 infill_first = 0
862 infill_only_where_needed = 0
863 infill_speed = 60
864 interface_shells = 0
865 layer_height = 0.3
866 min_skirt_length = 0
867 notes =
868 only_retract_when_crossing_perimeters = 1
869 ooze_prevention = 0
870 output_filename_format = [input_filename_base].gcode
871 overhangs = 1
872 perimeter_acceleration = 0
873 perimeter_extruder = 1
874 perimeter_extrusion_width = 0
875 perimeter_speed = 45
876 perimeters = 3
877 post_process =
878 raft_layers = 0
879 resolution = 0
880 seam_position = aligned
881 skirt_distance = 5
882 skirt_height = 1
883 skirts = 0
884 small_perimeter_speed = 30
885 solid_infill_below_area = 70
886 solid_infill_every_layers = 0
887 solid_infill_extrusion_width = 0
888 solid_infill_speed = 55
889 spiral_vase = 0
890 standby_temperature_delta = -5
891 support_material = 0
892 support_material_angle = 0
893 support_material_enforce_layers = 0
894 support_material_extruder = 1
895 support_material_extrusion_width = 0
896 support_material_interface_extruder = 1
897 support_material_interface_layers = 0
898 support_material_interface_spacing = 0
899 support_material_interface_speed = 100%
900 support_material_pattern = rectilinear
901 support_material_spacing = 2.5
902 support_material_speed = 60
903 support_material_threshold = 0
904 thin_walls = 1
905 threads = 2
906 top_infill_extrusion_width = 0
907 top_solid_infill_speed = 50
908 top_solid_layers = 3
909 travel_speed = 130
910  
911 [print:barb_print_config]
912 avoid_crossing_perimeters = 0
913 bottom_solid_layers = 3
914 bridge_acceleration = 1000
915 bridge_flow_ratio = 1
916 bridge_speed = 5
917 brim_width = 0
918 complete_objects = 0
919 default_acceleration = 500
920 dont_support_bridges = 1
921 external_fill_pattern = rectilinear
922 external_perimeter_extrusion_width = 0
923 external_perimeter_speed = 90%
924 external_perimeters_first = 0
925 extra_perimeters = 1
926 extruder_clearance_height = 20
927 extruder_clearance_radius = 20
928 extrusion_width = 0
929 fill_angle = 45
930 fill_density = 20%
931 fill_pattern = concentric
932 first_layer_acceleration = 500
933 first_layer_extrusion_width = 180%
934 first_layer_height = 0.3
935 first_layer_speed = 60%
936 gap_fill_speed = 10
937 gcode_comments = 0
938 infill_acceleration = 500
939 infill_every_layers = 1
940 infill_extruder = 1
941 infill_extrusion_width = 0
942 infill_first = 0
943 infill_only_where_needed = 0
944 infill_overlap = 15%
945 infill_speed = 60
946 interface_shells = 0
947 layer_height = 0.2
948 max_print_speed = 80
949 max_volumetric_speed = 0
950 min_skirt_length = 0
951 notes =
952 only_retract_when_crossing_perimeters = 1
953 ooze_prevention = 0
954 output_filename_format = [input_filename_base].gcode
955 overhangs = 1
956 perimeter_acceleration = 500
957 perimeter_extruder = 1
958 perimeter_extrusion_width = 0
959 perimeter_speed = 45
960 perimeters = 3
961 post_process =
962 raft_layers = 0
963 resolution = 0
964 seam_position = aligned
965 skirt_distance = 10
966 skirt_height = 1
967 skirts = 1
968 small_perimeter_speed = 10
969 solid_infill_below_area = 70
970 solid_infill_every_layers = 0
971 solid_infill_extruder = 1
972 solid_infill_extrusion_width = 0
973 solid_infill_speed = 55
974 spiral_vase = 0
975 standby_temperature_delta = -5
976 support_material = 1
977 support_material_angle = 0
978 support_material_contact_distance = 0.2
979 support_material_enforce_layers = 0
980 support_material_extruder = 1
981 support_material_extrusion_width = 0
982 support_material_interface_extruder = 1
983 support_material_interface_layers = 0
984 support_material_interface_spacing = 0
985 support_material_interface_speed = 100%
986 support_material_pattern = rectilinear-grid
987 support_material_spacing = 3
988 support_material_speed = 60
989 support_material_threshold = 0
990 thin_walls = 1
991 threads = 4
992 top_infill_extrusion_width = 0
993 top_solid_infill_speed = 50
994 top_solid_layers = 3
995 travel_speed = 130
996 xy_size_compensation = 0
997  
998 [print:config]
999 avoid_crossing_perimeters = 1
1000 bottom_solid_layers = 3
1001 bridge_acceleration = 1000
1002 bridge_flow_ratio = 1
1003 bridge_speed = 5
1004 brim_width = 0
1005 complete_objects = 0
1006 default_acceleration = 500
1007 dont_support_bridges = 1
1008 external_fill_pattern = concentric
1009 external_perimeter_extrusion_width = 0
1010 external_perimeter_speed = 90%
1011 external_perimeters_first = 0
1012 extra_perimeters = 1
1013 extruder_clearance_height = 20
1014 extruder_clearance_radius = 20
1015 extrusion_width = 0
1016 fill_angle = 45
1017 fill_density = 1%
1018 fill_pattern = honeycomb
1019 first_layer_acceleration = 500
1020 first_layer_extrusion_width = 180%
1021 first_layer_height = 0.3
1022 first_layer_speed = 60%
1023 gap_fill_speed = 10
1024 gcode_comments = 0
1025 infill_acceleration = 500
1026 infill_every_layers = 1
1027 infill_extruder = 1
1028 infill_extrusion_width = 0
1029 infill_first = 0
1030 infill_only_where_needed = 0
1031 infill_overlap = 15%
1032 infill_speed = 60
1033 interface_shells = 0
1034 layer_height = 0.3
1035 max_print_speed = 80
1036 max_volumetric_speed = 0
1037 min_skirt_length = 0
1038 notes =
1039 only_retract_when_crossing_perimeters = 1
1040 ooze_prevention = 0
1041 output_filename_format = [input_filename_base].gcode
1042 overhangs = 1
1043 perimeter_acceleration = 500
1044 perimeter_extruder = 1
1045 perimeter_extrusion_width = 0
1046 perimeter_speed = 45
1047 perimeters = 1
1048 post_process =
1049 raft_layers = 0
1050 resolution = 0
1051 seam_position = aligned
1052 skirt_distance = 10
1053 skirt_height = 1
1054 skirts = 2
1055 small_perimeter_speed = 30
1056 solid_infill_below_area = 50
1057 solid_infill_every_layers = 0
1058 solid_infill_extruder = 1
1059 solid_infill_extrusion_width = 0
1060 solid_infill_speed = 55
1061 spiral_vase = 0
1062 standby_temperature_delta = -5
1063 support_material = 0
1064 support_material_angle = 0
1065 support_material_contact_distance = 0.2
1066 support_material_enforce_layers = 0
1067 support_material_extruder = 1
1068 support_material_extrusion_width = 0
1069 support_material_interface_extruder = 1
1070 support_material_interface_layers = 0
1071 support_material_interface_spacing = 0
1072 support_material_interface_speed = 100%
1073 support_material_pattern = rectilinear
1074 support_material_spacing = 2.5
1075 support_material_speed = 60
1076 support_material_threshold = 0
1077 thin_walls = 1
1078 threads = 4
1079 top_infill_extrusion_width = 0
1080 top_solid_infill_speed = 50
1081 top_solid_layers = 3
1082 travel_speed = 130
1083 xy_size_compensation = 0
1084  
1085 [print:config_gears]
1086 avoid_crossing_perimeters = 0
1087 bottom_solid_layers = 3
1088 bridge_acceleration = 1000
1089 bridge_flow_ratio = 1
1090 bridge_speed = 5
1091 brim_width = 0
1092 complete_objects = 0
1093 default_acceleration = 500
1094 dont_support_bridges = 1
1095 external_fill_pattern = rectilinear
1096 external_perimeter_extrusion_width = 0
1097 external_perimeter_speed = 90%
1098 external_perimeters_first = 0
1099 extra_perimeters = 1
1100 extruder_clearance_height = 20
1101 extruder_clearance_radius = 20
1102 extrusion_width = 0
1103 fill_angle = 45
1104 fill_density = 15%
1105 fill_pattern = honeycomb
1106 first_layer_acceleration = 500
1107 first_layer_extrusion_width = 180%
1108 first_layer_height = 0.3
1109 first_layer_speed = 60%
1110 gap_fill_speed = 10
1111 gcode_comments = 0
1112 infill_acceleration = 500
1113 infill_every_layers = 1
1114 infill_extruder = 1
1115 infill_extrusion_width = 0
1116 infill_first = 0
1117 infill_only_where_needed = 0
1118 infill_overlap = 15%
1119 infill_speed = 60
1120 interface_shells = 0
1121 layer_height = 0.3
1122 min_skirt_length = 0
1123 notes =
1124 only_retract_when_crossing_perimeters = 1
1125 ooze_prevention = 0
1126 output_filename_format = [input_filename_base].gcode
1127 overhangs = 1
1128 perimeter_acceleration = 500
1129 perimeter_extruder = 1
1130 perimeter_extrusion_width = 0
1131 perimeter_speed = 45
1132 perimeters = 2
1133 post_process =
1134 raft_layers = 0
1135 resolution = 0
1136 seam_position = aligned
1137 skirt_distance = 10
1138 skirt_height = 1
1139 skirts = 1
1140 small_perimeter_speed = 30
1141 solid_infill_below_area = 70
1142 solid_infill_every_layers = 0
1143 solid_infill_extruder = 1
1144 solid_infill_extrusion_width = 0
1145 solid_infill_speed = 55
1146 spiral_vase = 0
1147 standby_temperature_delta = -5
1148 support_material = 0
1149 support_material_angle = 0
1150 support_material_contact_distance = 0.2
1151 support_material_enforce_layers = 0
1152 support_material_extruder = 1
1153 support_material_extrusion_width = 0
1154 support_material_interface_extruder = 1
1155 support_material_interface_layers = 0
1156 support_material_interface_spacing = 0
1157 support_material_interface_speed = 100%
1158 support_material_pattern = rectilinear
1159 support_material_spacing = 2.5
1160 support_material_speed = 60
1161 support_material_threshold = 0
1162 thin_walls = 1
1163 threads = 4
1164 top_infill_extrusion_width = 0
1165 top_solid_infill_speed = 50
1166 top_solid_layers = 3
1167 travel_speed = 130
1168 xy_size_compensation = 0
1169  
1170 [print:engine_config]
1171 avoid_crossing_perimeters = 0
1172 bottom_solid_layers = 3
1173 bridge_acceleration = 1000
1174 bridge_flow_ratio = 1
1175 bridge_speed = 5
1176 brim_width = 0
1177 complete_objects = 0
1178 default_acceleration = 500
1179 dont_support_bridges = 1
1180 external_fill_pattern = concentric
1181 external_perimeter_extrusion_width = 0
1182 external_perimeter_speed = 90%
1183 external_perimeters_first = 0
1184 extra_perimeters = 1
1185 extruder_clearance_height = 20
1186 extruder_clearance_radius = 20
1187 extrusion_width = 0
1188 fill_angle = 45
1189 fill_density = 1%
1190 fill_pattern = honeycomb
1191 first_layer_acceleration = 500
1192 first_layer_extrusion_width = 180%
1193 first_layer_height = 0.3
1194 first_layer_speed = 60%
1195 gap_fill_speed = 10
1196 gcode_comments = 0
1197 infill_acceleration = 500
1198 infill_every_layers = 1
1199 infill_extruder = 1
1200 infill_extrusion_width = 0
1201 infill_first = 0
1202 infill_only_where_needed = 0
1203 infill_overlap = 15%
1204 infill_speed = 60
1205 interface_shells = 0
1206 layer_height = 0.3
1207 max_print_speed = 80
1208 max_volumetric_speed = 0
1209 min_skirt_length = 0
1210 notes =
1211 only_retract_when_crossing_perimeters = 1
1212 ooze_prevention = 0
1213 output_filename_format = [input_filename_base].gcode
1214 overhangs = 0
1215 perimeter_acceleration = 500
1216 perimeter_extruder = 1
1217 perimeter_extrusion_width = 0
1218 perimeter_speed = 45
1219 perimeters = 1
1220 post_process =
1221 raft_layers = 0
1222 resolution = 0
1223 seam_position = aligned
1224 skirt_distance = 10
1225 skirt_height = 1
1226 skirts = 2
1227 small_perimeter_speed = 30
1228 solid_infill_below_area = 50
1229 solid_infill_every_layers = 0
1230 solid_infill_extruder = 1
1231 solid_infill_extrusion_width = 0
1232 solid_infill_speed = 55
1233 spiral_vase = 0
1234 standby_temperature_delta = -5
1235 support_material = 0
1236 support_material_angle = 0
1237 support_material_contact_distance = 0.2
1238 support_material_enforce_layers = 0
1239 support_material_extruder = 1
1240 support_material_extrusion_width = 0
1241 support_material_interface_extruder = 1
1242 support_material_interface_layers = 0
1243 support_material_interface_spacing = 0
1244 support_material_interface_speed = 100%
1245 support_material_pattern = rectilinear
1246 support_material_spacing = 2.5
1247 support_material_speed = 60
1248 support_material_threshold = 0
1249 thin_walls = 0
1250 threads = 4
1251 top_infill_extrusion_width = 0
1252 top_solid_infill_speed = 50
1253 top_solid_layers = 3
1254 travel_speed = 130
1255 xy_size_compensation = 0
1256  
1257 [print:engine_nozzle_config]
1258 avoid_crossing_perimeters = 0
1259 bottom_solid_layers = 3
1260 bridge_acceleration = 1000
1261 bridge_flow_ratio = 1
1262 bridge_speed = 5
1263 brim_width = 0
1264 complete_objects = 0
1265 default_acceleration = 500
1266 dont_support_bridges = 1
1267 external_fill_pattern = concentric
1268 external_perimeter_extrusion_width = 0
1269 external_perimeter_speed = 90%
1270 external_perimeters_first = 0
1271 extra_perimeters = 1
1272 extruder_clearance_height = 20
1273 extruder_clearance_radius = 20
1274 extrusion_width = 0
1275 fill_angle = 45
1276 fill_density = 40%
1277 fill_pattern = honeycomb
1278 first_layer_acceleration = 500
1279 first_layer_extrusion_width = 180%
1280 first_layer_height = 0.3
1281 first_layer_speed = 60%
1282 gap_fill_speed = 10
1283 gcode_comments = 0
1284 infill_acceleration = 500
1285 infill_every_layers = 1
1286 infill_extruder = 1
1287 infill_extrusion_width = 0
1288 infill_first = 0
1289 infill_only_where_needed = 0
1290 infill_overlap = 15%
1291 infill_speed = 60
1292 interface_shells = 0
1293 layer_height = 0.2
1294 max_print_speed = 80
1295 max_volumetric_speed = 0
1296 min_skirt_length = 0
1297 notes =
1298 only_retract_when_crossing_perimeters = 1
1299 ooze_prevention = 0
1300 output_filename_format = [input_filename_base].gcode
1301 overhangs = 1
1302 perimeter_acceleration = 500
1303 perimeter_extruder = 1
1304 perimeter_extrusion_width = 0
1305 perimeter_speed = 45
1306 perimeters = 2
1307 post_process =
1308 raft_layers = 0
1309 resolution = 0
1310 seam_position = aligned
1311 skirt_distance = 10
1312 skirt_height = 1
1313 skirts = 2
1314 small_perimeter_speed = 30
1315 solid_infill_below_area = 50
1316 solid_infill_every_layers = 0
1317 solid_infill_extruder = 1
1318 solid_infill_extrusion_width = 0
1319 solid_infill_speed = 55
1320 spiral_vase = 0
1321 standby_temperature_delta = -5
1322 support_material = 0
1323 support_material_angle = 0
1324 support_material_contact_distance = 0.2
1325 support_material_enforce_layers = 0
1326 support_material_extruder = 1
1327 support_material_extrusion_width = 0
1328 support_material_interface_extruder = 1
1329 support_material_interface_layers = 0
1330 support_material_interface_spacing = 0
1331 support_material_interface_speed = 100%
1332 support_material_pattern = rectilinear
1333 support_material_spacing = 2.5
1334 support_material_speed = 60
1335 support_material_threshold = 0
1336 thin_walls = 1
1337 threads = 4
1338 top_infill_extrusion_width = 0
1339 top_solid_infill_speed = 50
1340 top_solid_layers = 6
1341 travel_speed = 130
1342 xy_size_compensation = 0
1343  
1344 [print:holder_print_config]
1345 avoid_crossing_perimeters = 0
1346 bottom_solid_layers = 3
1347 bridge_acceleration = 1000
1348 bridge_flow_ratio = 1
1349 bridge_speed = 5
1350 brim_width = 0
1351 complete_objects = 0
1352 default_acceleration = 500
1353 dont_support_bridges = 1
1354 external_fill_pattern = rectilinear
1355 external_perimeter_extrusion_width = 0
1356 external_perimeter_speed = 90%
1357 external_perimeters_first = 0
1358 extra_perimeters = 1
1359 extruder_clearance_height = 20
1360 extruder_clearance_radius = 20
1361 extrusion_width = 0
1362 fill_angle = 45
1363 fill_density = 10%
1364 fill_pattern = rectilinear
1365 first_layer_acceleration = 500
1366 first_layer_extrusion_width = 180%
1367 first_layer_height = 0.3
1368 first_layer_speed = 60%
1369 gap_fill_speed = 10
1370 gcode_comments = 0
1371 infill_acceleration = 500
1372 infill_every_layers = 1
1373 infill_extruder = 1
1374 infill_extrusion_width = 0
1375 infill_first = 0
1376 infill_only_where_needed = 0
1377 infill_overlap = 15%
1378 infill_speed = 60
1379 interface_shells = 0
1380 layer_height = 0.3
1381 max_print_speed = 80
1382 max_volumetric_speed = 0
1383 min_skirt_length = 0
1384 notes =
1385 only_retract_when_crossing_perimeters = 1
1386 ooze_prevention = 0
1387 output_filename_format = [input_filename_base].gcode
1388 overhangs = 1
1389 perimeter_acceleration = 500
1390 perimeter_extruder = 1
1391 perimeter_extrusion_width = 0
1392 perimeter_speed = 45
1393 perimeters = 1
1394 post_process =
1395 raft_layers = 0
1396 resolution = 0
1397 seam_position = aligned
1398 skirt_distance = 10
1399 skirt_height = 1
1400 skirts = 1
1401 small_perimeter_speed = 10
1402 solid_infill_below_area = 70
1403 solid_infill_every_layers = 0
1404 solid_infill_extruder = 1
1405 solid_infill_extrusion_width = 0
1406 solid_infill_speed = 55
1407 spiral_vase = 0
1408 standby_temperature_delta = -5
1409 support_material = 0
1410 support_material_angle = 0
1411 support_material_contact_distance = 0.2
1412 support_material_enforce_layers = 0
1413 support_material_extruder = 1
1414 support_material_extrusion_width = 0
1415 support_material_interface_extruder = 1
1416 support_material_interface_layers = 0
1417 support_material_interface_spacing = 0
1418 support_material_interface_speed = 100%
1419 support_material_pattern = rectilinear
1420 support_material_spacing = 2.5
1421 support_material_speed = 60
1422 support_material_threshold = 0
1423 thin_walls = 1
1424 threads = 4
1425 top_infill_extrusion_width = 0
1426 top_solid_infill_speed = 50
1427 top_solid_layers = 3
1428 travel_speed = 130
1429 xy_size_compensation = 0
1430  
1431 [print:pad_config]
1432 avoid_crossing_perimeters = 0
1433 bottom_solid_layers = 3
1434 bridge_acceleration = 1000
1435 bridge_flow_ratio = 1
1436 bridge_speed = 15
1437 brim_width = 0
1438 complete_objects = 0
1439 default_acceleration = 500
1440 dont_support_bridges = 1
1441 external_fill_pattern = rectilinear
1442 external_perimeter_extrusion_width = 0
1443 external_perimeter_speed = 90%
1444 external_perimeters_first = 0
1445 extra_perimeters = 1
1446 extruder_clearance_height = 20
1447 extruder_clearance_radius = 20
1448 extrusion_width = 0
1449 fill_angle = 45
1450 fill_density = 15%
1451 fill_pattern = honeycomb
1452 first_layer_acceleration = 500
1453 first_layer_extrusion_width = 200%
1454 first_layer_height = 0.3
1455 first_layer_speed = 60%
1456 gap_fill_speed = 20
1457 gcode_comments = 0
1458 infill_acceleration = 500
1459 infill_every_layers = 1
1460 infill_extruder = 1
1461 infill_extrusion_width = 0
1462 infill_first = 0
1463 infill_only_where_needed = 0
1464 infill_overlap = 15%
1465 infill_speed = 60
1466 interface_shells = 0
1467 layer_height = 0.2
1468 max_print_speed = 80
1469 max_volumetric_speed = 0
1470 min_skirt_length = 0
1471 notes =
1472 only_retract_when_crossing_perimeters = 1
1473 ooze_prevention = 0
1474 output_filename_format = [input_filename_base].gcode
1475 overhangs = 1
1476 perimeter_acceleration = 500
1477 perimeter_extruder = 1
1478 perimeter_extrusion_width = 0
1479 perimeter_speed = 45
1480 perimeters = 1
1481 post_process =
1482 raft_layers = 0
1483 resolution = 0
1484 seam_position = aligned
1485 skirt_distance = 4
1486 skirt_height = 1
1487 skirts = 2
1488 small_perimeter_speed = 30
1489 solid_infill_below_area = 70
1490 solid_infill_every_layers = 0
1491 solid_infill_extruder = 1
1492 solid_infill_extrusion_width = 0
1493 solid_infill_speed = 55
1494 spiral_vase = 0
1495 standby_temperature_delta = -5
1496 support_material = 0
1497 support_material_angle = 0
1498 support_material_contact_distance = 0.2
1499 support_material_enforce_layers = 0
1500 support_material_extruder = 1
1501 support_material_extrusion_width = 0
1502 support_material_interface_extruder = 1
1503 support_material_interface_layers = 0
1504 support_material_interface_spacing = 0
1505 support_material_interface_speed = 100%
1506 support_material_pattern = rectilinear
1507 support_material_spacing = 2.5
1508 support_material_speed = 60
1509 support_material_threshold = 0
1510 thin_walls = 1
1511 threads = 2
1512 top_infill_extrusion_width = 0
1513 top_solid_infill_speed = 50
1514 top_solid_layers = 3
1515 travel_speed = 130
1516 xy_size_compensation = 0
1517  
1518 [print:slic3r_config]
1519 avoid_crossing_perimeters = 0
1520 bottom_solid_layers = 3
1521 bridge_acceleration = 1000
1522 bridge_flow_ratio = 1
1523 bridge_speed = 15
1524 brim_width = 0
1525 complete_objects = 0
1526 default_acceleration = 500
1527 dont_support_bridges = 1
1528 external_fill_pattern = rectilinear
1529 external_perimeter_extrusion_width = 0
1530 external_perimeter_speed = 90%
1531 external_perimeters_first = 0
1532 extra_perimeters = 1
1533 extruder_clearance_height = 20
1534 extruder_clearance_radius = 20
1535 extrusion_width = 0
1536 fill_angle = 45
1537 fill_density = 15%
1538 fill_pattern = honeycomb
1539 first_layer_acceleration = 500
1540 first_layer_extrusion_width = 200%
1541 first_layer_height = 0.3
1542 first_layer_speed = 60%
1543 gap_fill_speed = 20
1544 gcode_comments = 0
1545 infill_acceleration = 500
1546 infill_every_layers = 1
1547 infill_extruder = 1
1548 infill_extrusion_width = 0
1549 infill_first = 0
1550 infill_only_where_needed = 0
1551 infill_overlap = 15%
1552 infill_speed = 60
1553 interface_shells = 0
1554 layer_height = 0.2
1555 max_print_speed = 80
1556 max_volumetric_speed = 0
1557 min_skirt_length = 0
1558 notes =
1559 only_retract_when_crossing_perimeters = 1
1560 ooze_prevention = 0
1561 output_filename_format = [input_filename_base].gcode
1562 overhangs = 1
1563 perimeter_acceleration = 500
1564 perimeter_extruder = 1
1565 perimeter_extrusion_width = 0
1566 perimeter_speed = 45
1567 perimeters = 1
1568 post_process =
1569 raft_layers = 0
1570 resolution = 0
1571 seam_position = aligned
1572 skirt_distance = 4
1573 skirt_height = 1
1574 skirts = 2
1575 small_perimeter_speed = 30
1576 solid_infill_below_area = 70
1577 solid_infill_every_layers = 0
1578 solid_infill_extruder = 1
1579 solid_infill_extrusion_width = 0
1580 solid_infill_speed = 55
1581 spiral_vase = 0
1582 standby_temperature_delta = -5
1583 support_material = 0
1584 support_material_angle = 0
1585 support_material_contact_distance = 0.2
1586 support_material_enforce_layers = 0
1587 support_material_extruder = 1
1588 support_material_extrusion_width = 0
1589 support_material_interface_extruder = 1
1590 support_material_interface_layers = 0
1591 support_material_interface_spacing = 0
1592 support_material_interface_speed = 100%
1593 support_material_pattern = rectilinear
1594 support_material_spacing = 2.5
1595 support_material_speed = 60
1596 support_material_threshold = 0
1597 thin_walls = 1
1598 threads = 2
1599 top_infill_extrusion_width = 0
1600 top_solid_infill_speed = 50
1601 top_solid_layers = 3
1602 travel_speed = 130
1603 xy_size_compensation = 0
1604  
1605 [printer:RebeliX]
1606 bed_shape = 0x0,180x0,180x180,0x180
1607 before_layer_gcode =
1608 end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n
1609 extruder_offset = 0x0
1610 gcode_flavor = reprap
1611 layer_gcode =
1612 nozzle_diameter = 0.4
1613 octoprint_apikey = B14197D3716442D4B0BB8F485877E31E
1614 octoprint_host = 192.168.1.106:5000
1615 pressure_advance = 0
1616 retract_before_travel = 2
1617 retract_layer_change = 1
1618 retract_length = 1.3
1619 retract_length_toolchange = 3
1620 retract_lift = 0
1621 retract_restart_extra = 0
1622 retract_restart_extra_toolchange = 0
1623 retract_speed = 60
1624 start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
1625 toolchange_gcode =
1626 use_firmware_retraction = 0
1627 use_relative_e_distances = 1
1628 use_volumetric_e = 0
1629 vibration_limit = 0
1630 wipe = 1
1631 z_offset = 0
1632  
1633 [printer:Simple Mode]
1634 bed_shape = 0x0,180x0,180x180,0x180
1635 end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
1636 gcode_flavor = reprap
1637 nozzle_diameter = 0.3
1638 retract_length = 1
1639 retract_lift = 0
1640 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
1641 z_offset = 0
1642  
1643 [printer:engine_config]
1644 bed_shape = 0x0,180x0,180x180,0x180
1645 before_layer_gcode =
1646 end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n
1647 extruder_offset = 0x0
1648 gcode_flavor = reprap
1649 layer_gcode =
1650 nozzle_diameter = 0.4
1651 octoprint_apikey = 330CC1C393FC4CD08C420E476D472A7E
1652 octoprint_host = 192.168.1.25
1653 pressure_advance = 0
1654 retract_before_travel = 2
1655 retract_layer_change = 0
1656 retract_length = 1.3
1657 retract_length_toolchange = 3
1658 retract_lift = 0
1659 retract_restart_extra = 0
1660 retract_restart_extra_toolchange = 0
1661 retract_speed = 60
1662 start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
1663 toolchange_gcode =
1664 use_firmware_retraction = 0
1665 use_relative_e_distances = 1
1666 use_volumetric_e = 0
1667 vibration_limit = 0
1668 wipe = 0
1669 z_offset = 0
1670  
1671 [printer:pad_config]
1672 bed_shape = 0x0,180x0,180x180,0x180
1673 before_layer_gcode =
1674 end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n
1675 extruder_offset = 0x0
1676 gcode_flavor = reprap
1677 layer_gcode =
1678 nozzle_diameter = 0.4
1679 octoprint_apikey = 330CC1C393FC4CD08C420E476D472A7E
1680 octoprint_host = 192.168.1.25
1681 pressure_advance = 0
1682 retract_before_travel = 2
1683 retract_layer_change = 1
1684 retract_length = 1.3
1685 retract_length_toolchange = 3
1686 retract_lift = 0
1687 retract_restart_extra = 0
1688 retract_restart_extra_toolchange = 0
1689 retract_speed = 60
1690 start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
1691 toolchange_gcode =
1692 use_firmware_retraction = 0
1693 use_relative_e_distances = 1
1694 use_volumetric_e = 0
1695 vibration_limit = 0
1696 wipe = 0
1697 z_offset = 0
1698  
1699 [printer:slic3r_config]
1700 bed_shape = 0x0,180x0,180x180,0x180
1701 before_layer_gcode =
1702 end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n
1703 extruder_offset = 0x0
1704 gcode_flavor = reprap
1705 layer_gcode =
1706 nozzle_diameter = 0.4
1707 octoprint_apikey = 330CC1C393FC4CD08C420E476D472A7E
1708 octoprint_host = 192.168.1.25
1709 pressure_advance = 0
1710 retract_before_travel = 2
1711 retract_layer_change = 1
1712 retract_length = 1.3
1713 retract_length_toolchange = 3
1714 retract_lift = 0
1715 retract_restart_extra = 0
1716 retract_restart_extra_toolchange = 0
1717 retract_speed = 60
1718 start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
1719 toolchange_gcode =
1720 use_firmware_retraction = 0
1721 use_relative_e_distances = 1
1722 use_volumetric_e = 0
1723 vibration_limit = 0
1724 wipe = 1
1725 z_offset = 0
1726  
1727 [settings]
1728 autocenter = 1
1729 mode = expert
1730  
1731 [simple]
1732 avoid_crossing_perimeters = 1
1733 bed_shape = 0x0,180x0,180x180,0x180
1734 bed_temperature = 110
1735 bottom_solid_layers = 3
1736 bridge_acceleration = 0
1737 bridge_fan_speed = 100
1738 bridge_flow_ratio = 1
1739 bridge_speed = 60
1740 brim_width = 0
1741 complete_objects = 0
1742 cooling = 1
1743 default_acceleration = 0
1744 disable_fan_first_layers = 1
1745 dont_support_bridges = 1
1746 duplicate_distance = 6
1747 end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
1748 external_fill_pattern = rectilinear
1749 external_perimeter_speed = 70%
1750 external_perimeters_first = 0
1751 extra_perimeters = 1
1752 extruder_clearance_height = 20
1753 extruder_clearance_radius = 20
1754 extruder_offset = 0x0
1755 extrusion_axis = E
1756 extrusion_multiplier = 1
1757 extrusion_width = 0
1758 fan_always_on = 0
1759 fan_below_layer_time = 60
1760 filament_diameter = 1.75
1761 fill_angle = 45
1762 fill_density = 40%
1763 fill_pattern = honeycomb
1764 first_layer_acceleration = 0
1765 first_layer_bed_temperature = 115
1766 first_layer_extrusion_width = 200%
1767 first_layer_height = 0.3
1768 first_layer_speed = 30%
1769 first_layer_temperature = 235
1770 gap_fill_speed = 20
1771 gcode_arcs = 0
1772 gcode_comments = 0
1773 gcode_flavor = reprap
1774 infill_acceleration = 0
1775 infill_every_layers = 10
1776 infill_extruder = 1
1777 infill_extrusion_width = 0
1778 infill_first = 0
1779 infill_only_where_needed = 0
1780 infill_speed = 60
1781 interface_shells = 0
1782 layer_gcode =
1783 layer_height = 0.2
1784 max_fan_speed = 100
1785 min_fan_speed = 35
1786 min_print_speed = 10
1787 min_skirt_length = 0
1788 notes =
1789 nozzle_diameter = 0.3
1790 only_retract_when_crossing_perimeters = 1
1791 ooze_prevention = 0
1792 output_filename_format = [input_filename_base].gcode
1793 overhangs = 1
1794 perimeter_acceleration = 0
1795 perimeter_extruder = 1
1796 perimeter_extrusion_width = 0
1797 perimeter_speed = 30
1798 perimeters = 3
1799 post_process =
1800 raft_layers = 0
1801 resolution = 0
1802 retract_before_travel = 2
1803 retract_layer_change = 1
1804 retract_length = 1
1805 retract_length_toolchange = 10
1806 retract_lift = 0
1807 retract_restart_extra = 0
1808 retract_restart_extra_toolchange = 0
1809 retract_speed = 30
1810 seam_position = aligned
1811 skirt_distance = 6
1812 skirt_height = 1
1813 skirts = 1
1814 slowdown_below_layer_time = 30
1815 small_perimeter_speed = 30
1816 solid_infill_below_area = 70
1817 solid_infill_every_layers = 0
1818 solid_infill_extrusion_width = 0
1819 solid_infill_speed = 60
1820 spiral_vase = 0
1821 standby_temperature_delta = -5
1822 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
1823 support_material = 0
1824 support_material_angle = 0
1825 support_material_enforce_layers = 0
1826 support_material_extruder = 1
1827 support_material_extrusion_width = 0
1828 support_material_interface_extruder = 1
1829 support_material_interface_layers = 3
1830 support_material_interface_spacing = 0
1831 support_material_interface_speed = 100%
1832 support_material_pattern = pillars
1833 support_material_spacing = 2.5
1834 support_material_speed = 60
1835 support_material_threshold = 0
1836 temperature = 230
1837 thin_walls = 1
1838 threads = 2
1839 toolchange_gcode =
1840 top_infill_extrusion_width = 0
1841 top_solid_infill_speed = 50
1842 top_solid_layers = 3
1843 travel_speed = 130
1844 use_firmware_retraction = 0
1845 use_relative_e_distances = 0
1846 vibration_limit = 0
1847 wipe = 0
1848 z_offset = 0