Rev Author Line No. Line
4392 kaklik 1 # generated by Slic3r 1.3.0-dev on Mon Jan 11 23:22:25 2016
2 avoid_crossing_perimeters = 0
3 bed_shape = 0x0,180x0,180x180,0x180
4 bed_temperature = 50
5 before_layer_gcode =
6 bottom_solid_layers = 3
7 bridge_acceleration = 1000
8 bridge_fan_speed = 100
9 bridge_flow_ratio = 1
10 bridge_speed = 5
11 brim_width = 0
12 complete_objects = 0
13 cooling = 1
14 default_acceleration = 500
15 disable_fan_first_layers = 1
16 dont_support_bridges = 1
17 duplicate_distance = 6
18 end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n
19 external_fill_pattern = rectilinear
20 external_perimeter_extrusion_width = 0
21 external_perimeter_speed = 90%
22 external_perimeters_first = 0
23 extra_perimeters = 1
24 extruder_clearance_height = 20
25 extruder_clearance_radius = 20
26 extruder_offset = 0x0
27 extrusion_axis = E
28 extrusion_multiplier = 1
29 extrusion_width = 0
30 fan_always_on = 1
31 fan_below_layer_time = 60
32 filament_colour = #FFFFFF
33 filament_diameter = 1.75
34 filament_settings_id =
35 fill_angle = 45
36 fill_density = 10%
37 fill_pattern = honeycomb
38 first_layer_acceleration = 500
39 first_layer_bed_temperature = 60
40 first_layer_extrusion_width = 180%
41 first_layer_height = 0.3
42 first_layer_speed = 60%
43 first_layer_temperature = 212
44 gap_fill_speed = 10
45 gcode_arcs = 0
46 gcode_comments = 0
47 gcode_flavor = reprap
48 infill_acceleration = 500
49 infill_every_layers = 1
50 infill_extruder = 1
51 infill_extrusion_width = 0
52 infill_first = 0
53 infill_only_where_needed = 0
54 infill_overlap = 15%
55 infill_speed = 60
56 interface_shells = 0
57 layer_gcode =
58 layer_height = 0.2
59 max_fan_speed = 100
60 max_print_speed = 80
61 max_volumetric_speed = 0
62 min_fan_speed = 100
63 min_print_speed = 10
64 min_skirt_length = 0
65 notes =
66 nozzle_diameter = 0.4
67 octoprint_apikey = 330CC1C393FC4CD08C420E476D472A7E
68 octoprint_host = 192.168.1.23
69 only_retract_when_crossing_perimeters = 1
70 ooze_prevention = 0
71 output_filename_format = [input_filename_base].gcode
72 overhangs = 1
73 perimeter_acceleration = 500
74 perimeter_extruder = 1
75 perimeter_extrusion_width = 0
76 perimeter_speed = 45
77 perimeters = 2
78 post_process =
79 pressure_advance = 0
80 print_settings_id =
81 printer_settings_id =
82 raft_layers = 0
83 resolution = 0
84 retract_before_travel = 2
85 retract_layer_change = 1
86 retract_length = 1.3
87 retract_length_toolchange = 3
88 retract_lift = 0
89 retract_lift_above = 0
90 retract_lift_below = 0
91 retract_restart_extra = 0
92 retract_restart_extra_toolchange = 0
93 retract_speed = 60
94 seam_position = aligned
95 serial_port =
96 serial_speed = 250000
97 skirt_distance = 10
98 skirt_height = 1
99 skirts = 3
100 slowdown_below_layer_time = 30
101 small_perimeter_speed = 10
102 solid_infill_below_area = 70
103 solid_infill_every_layers = 0
104 solid_infill_extruder = 1
105 solid_infill_extrusion_width = 0
106 solid_infill_speed = 55
107 spiral_vase = 0
108 standby_temperature_delta = -5
109 start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
110 support_material = 0
111 support_material_angle = 0
112 support_material_contact_distance = 0.2
113 support_material_enforce_layers = 0
114 support_material_extruder = 1
115 support_material_extrusion_width = 0
116 support_material_interface_extruder = 1
117 support_material_interface_layers = 0
118 support_material_interface_spacing = 0
119 support_material_interface_speed = 100%
120 support_material_pattern = rectilinear
121 support_material_spacing = 2.5
122 support_material_speed = 60
123 support_material_threshold = 0
124 temperature = 212
125 thin_walls = 1
126 threads = 4
127 toolchange_gcode =
128 top_infill_extrusion_width = 0
129 top_solid_infill_speed = 50
130 top_solid_layers = 3
131 travel_speed = 130
132 use_firmware_retraction = 0
133 use_relative_e_distances = 1
134 use_volumetric_e = 0
135 vibration_limit = 0
136 wipe = 1
137 xy_size_compensation = 0
138 z_offset = 0