Rev Author Line No. Line
4605 kaklik 1 [profile]
2 layer_height = 0.3
3 wall_thickness = 0.8
4 retraction_enable = True
5 solid_layer_thickness = 0.6
6 fill_density = 25
7 nozzle_size = 0.4
8 print_speed = 50
9 print_temperature = 212
10 print_temperature2 = 0
11 print_temperature3 = 0
12 print_temperature4 = 0
13 print_temperature5 = 0
14 print_bed_temperature = 55
15 support = None
16 platform_adhesion = None
17 support_dual_extrusion = Both
18 wipe_tower = False
19 wipe_tower_volume = 15
20 ooze_shield = False
21 filament_diameter = 1,75
22 filament_diameter2 = 0
23 filament_diameter3 = 0
24 filament_diameter4 = 0
25 filament_diameter5 = 0
26 filament_flow = 100.0
27 retraction_speed = 40.0
28 retraction_amount = 4.5
29 retraction_dual_amount = 16.5
30 retraction_min_travel = 1.5
31 retraction_combing = All
32 retraction_minimal_extrusion = 0.02
33 retraction_hop = 0.0
34 bottom_thickness = 0.3
35 layer0_width_factor = 200
36 object_sink = 0.0
37 overlap_dual = 0.15
38 travel_speed = 100
39 bottom_layer_speed = 20
40 infill_speed = 0.0
41 solidarea_speed = 0.0
42 inset0_speed = 0.0
43 insetx_speed = 0.0
44 cool_min_layer_time = 10
45 fan_enabled = True
46 skirt_line_count = 1
47 skirt_gap = 3.0
48 skirt_minimal_length = 150.0
49 fan_full_height = 5.0
50 fan_speed = 100
51 fan_speed_max = 100
52 cool_min_feedrate = 10
53 cool_head_lift = False
54 solid_top = True
55 solid_bottom = True
56 fill_overlap = 15
57 perimeter_before_infill = True
58 support_type = Lines
59 support_angle = 60
60 support_fill_rate = 15
61 support_xy_distance = 0.7
62 support_z_distance = 0.15
63 spiralize = False
64 simple_mode = False
65 brim_line_count = 20
66 raft_margin = 5.0
67 raft_line_spacing = 3.0
68 raft_base_thickness = 0.3
69 raft_base_linewidth = 1.0
70 raft_interface_thickness = 0.27
71 raft_interface_linewidth = 0.4
72 raft_airgap_all = 0.0
73 raft_airgap = 0.22
74 raft_surface_layers = 4
75 raft_surface_thickness = 0.27
76 raft_surface_linewidth = 0.4
77 fix_horrible_union_all_type_a = True
78 fix_horrible_union_all_type_b = False
79 fix_horrible_use_open_bits = False
80 fix_horrible_extensive_stitching = False
81 plugin_config = (lp1
82 .
83 object_center_x = -1
84 object_center_y = -1
85  
86 [alterations]
87 start.gcode = ;Sliced at: {day} {date} {time}
88 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
89 ;Print time: {print_time}
90 ;Filament used: {filament_amount}m {filament_weight}g
91 ;Filament cost: {filament_cost}
92 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
93 ;M109 S{print_temperature} ;Uncomment to add your own temperature line
94 G21 ;metric values
95 G90 ;absolute positioning
96 M82 ;set extruder to absolute mode
97 M107 ;start with the fan off
98 G28 X0 Y0 ;move X/Y to min endstops
99 G28 Z0 ;move Z to min endstops
100 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
101 G92 E0 ;zero the extruded length
102 G1 F200 E3 ;extrude 3mm of feed stock
103 G92 E0 ;zero the extruded length again
104 G1 F{travel_speed}
105 ;Put printing message on LCD screen
106 M117 Printing...
107 end.gcode = ;End GCode
108 M104 S0 ;extruder heater off
109 M140 S0 ;heated bed heater off (if you have it)
110 G91 ;relative positioning
111 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
112 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
113 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
114 M84 ;steppers off
115 G90 ;absolute positioning
116 ;{profile_string}
117 start2.gcode = ;Sliced at: {day} {date} {time}
118 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
119 ;Print time: {print_time}
120 ;Filament used: {filament_amount}m {filament_weight}g
121 ;Filament cost: {filament_cost}
122 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
123 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
124 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
125 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
126 G21 ;metric values
127 G90 ;absolute positioning
128 M107 ;start with the fan off
129 G28 X0 Y0 ;move X/Y to min endstops
130 G28 Z0 ;move Z to min endstops
131 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
132 T1 ;Switch to the 2nd extruder
133 G92 E0 ;zero the extruded length
134 G1 F200 E10 ;extrude 10mm of feed stock
135 G92 E0 ;zero the extruded length again
136 G1 F200 E-{retraction_dual_amount}
137 T0 ;Switch to the first extruder
138 G92 E0 ;zero the extruded length
139 G1 F200 E10 ;extrude 10mm of feed stock
140 G92 E0 ;zero the extruded length again
141 G1 F{travel_speed}
142 ;Put printing message on LCD screen
143 M117 Printing...
144 end2.gcode = ;End GCode
145 M104 T0 S0 ;extruder heater off
146 M104 T1 S0 ;extruder heater off
147 M140 S0 ;heated bed heater off (if you have it)
148 G91 ;relative positioning
149 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
150 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
151 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
152 M84 ;steppers off
153 G90 ;absolute positioning
154 ;{profile_string}
155 start3.gcode = ;Sliced at: {day} {date} {time}
156 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
157 ;Print time: {print_time}
158 ;Filament used: {filament_amount}m {filament_weight}g
159 ;Filament cost: {filament_cost}
160 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
161 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
162 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
163 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
164 G21 ;metric values
165 G90 ;absolute positioning
166 M107 ;start with the fan off
167 G28 X0 Y0 ;move X/Y to min endstops
168 G28 Z0 ;move Z to min endstops
169 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
170 T2 ;Switch to the 3rd extruder
171 G92 E0 ;zero the extruded length
172 G1 F200 E10 ;extrude 10mm of feed stock
173 G92 E0 ;zero the extruded length again
174 G1 F200 E-{retraction_dual_amount}
175 T1 ;Switch to the 2nd extruder
176 G92 E0 ;zero the extruded length
177 G1 F200 E10 ;extrude 10mm of feed stock
178 G92 E0 ;zero the extruded length again
179 G1 F200 E-{retraction_dual_amount}
180 T0 ;Switch to the first extruder
181 G92 E0 ;zero the extruded length
182 G1 F200 E10 ;extrude 10mm of feed stock
183 G92 E0 ;zero the extruded length again
184 G1 F{travel_speed}
185 ;Put printing message on LCD screen
186 M117 Printing...
187 end3.gcode = ;End GCode
188 M104 T0 S0 ;extruder heater off
189 M104 T1 S0 ;extruder heater off
190 M104 T2 S0 ;extruder heater off
191 M140 S0 ;heated bed heater off (if you have it)
192 G91 ;relative positioning
193 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
194 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
195 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
196 M84 ;steppers off
197 G90 ;absolute positioning
198 ;{profile_string}
199 start4.gcode = ;Sliced at: {day} {date} {time}
200 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
201 ;Print time: {print_time}
202 ;Filament used: {filament_amount}m {filament_weight}g
203 ;Filament cost: {filament_cost}
204 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
205 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
206 ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
207 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
208 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
209 G21 ;metric values
210 G90 ;absolute positioning
211 M107 ;start with the fan off
212 G28 X0 Y0 ;move X/Y to min endstops
213 G28 Z0 ;move Z to min endstops
214 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
215 T3 ;Switch to the 4th extruder
216 G92 E0 ;zero the extruded length
217 G1 F200 E10 ;extrude 10mm of feed stock
218 G92 E0 ;zero the extruded length again
219 G1 F200 E-{retraction_dual_amount}
220 T2 ;Switch to the 3rd extruder
221 G92 E0 ;zero the extruded length
222 G1 F200 E10 ;extrude 10mm of feed stock
223 G92 E0 ;zero the extruded length again
224 G1 F200 E-{retraction_dual_amount}
225 T1 ;Switch to the 2nd extruder
226 G92 E0 ;zero the extruded length
227 G1 F200 E10 ;extrude 10mm of feed stock
228 G92 E0 ;zero the extruded length again
229 G1 F200 E-{retraction_dual_amount}
230 T0 ;Switch to the first extruder
231 G92 E0 ;zero the extruded length
232 G1 F200 E10 ;extrude 10mm of feed stock
233 G92 E0 ;zero the extruded length again
234 G1 F{travel_speed}
235 ;Put printing message on LCD screen
236 M117 Printing...
237 end4.gcode = ;End GCode
238 M104 T0 S0 ;extruder heater off
239 M104 T1 S0 ;extruder heater off
240 M104 T2 S0 ;extruder heater off
241 M104 T3 S0 ;extruder heater off
242 M140 S0 ;heated bed heater off (if you have it)
243 G91 ;relative positioning
244 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
245 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
246 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
247 M84 ;steppers off
248 G90 ;absolute positioning
249 ;{profile_string}
250 support_start.gcode =
251 support_end.gcode =
252 cool_start.gcode =
253 cool_end.gcode =
254 replace.csv =
255 preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
256 ;This code is added before the T(n)
257 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
258 ;This code is added after the T(n)
259