Rev Author Line No. Line
3873 kaklik 1 # generated by Slic3r 1.2.6 on Fri Feb 6 00:27:19 2015
2 avoid_crossing_perimeters = 0
3 bed_shape = 0x0,180x0,180x180,0x180
4 bed_temperature = 90
5 before_layer_gcode =
6 bottom_solid_layers = 3
7 bridge_acceleration = 1000
8 bridge_fan_speed = 0
9 bridge_flow_ratio = 1
10 bridge_speed = 10
11 brim_width = 0
12 complete_objects = 0
13 cooling = 1
14 default_acceleration = 500
15 disable_fan_first_layers = 0
16 dont_support_bridges = 1
17 duplicate_distance = 6
18 end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n
19 external_fill_pattern = rectilinear
20 external_perimeter_extrusion_width = 0
21 external_perimeter_speed = 90%
22 external_perimeters_first = 0
23 extra_perimeters = 1
24 extruder_clearance_height = 20
25 extruder_clearance_radius = 20
26 extruder_offset = 0x0
27 extrusion_axis = E
28 extrusion_multiplier = 1
29 extrusion_width = 0
30 fan_always_on = 0
31 fan_below_layer_time = 5
32 filament_diameter = 1.75
33 fill_angle = 45
34 fill_density = 25%
35 fill_pattern = line
36 first_layer_acceleration = 500
37 first_layer_bed_temperature = 90
38 first_layer_extrusion_width = 180%
39 first_layer_height = 0.3
40 first_layer_speed = 60%
41 first_layer_temperature = 225
42 gap_fill_speed = 20
43 gcode_arcs = 0
44 gcode_comments = 0
45 gcode_flavor = reprap
46 infill_acceleration = 500
47 infill_every_layers = 1
48 infill_extruder = 1
49 infill_extrusion_width = 0
50 infill_first = 0
51 infill_only_where_needed = 0
52 infill_overlap = 15%
53 infill_speed = 60
54 interface_shells = 0
55 layer_gcode =
56 layer_height = 0.3
57 max_fan_speed = 100
58 min_fan_speed = 50
59 min_print_speed = 15
60 min_skirt_length = 0
61 notes =
62 nozzle_diameter = 0.4
63 octoprint_apikey = B14197D3716442D4B0BB8F485877E31E
64 octoprint_host = 192.168.1.106:5000
65 only_retract_when_crossing_perimeters = 1
66 ooze_prevention = 0
67 output_filename_format = [input_filename_base].gcode
68 overhangs = 1
69 perimeter_acceleration = 500
70 perimeter_extruder = 1
71 perimeter_extrusion_width = 0
72 perimeter_speed = 45
73 perimeters = 2
74 post_process =
75 pressure_advance = 0
76 raft_layers = 0
77 resolution = 0
78 retract_before_travel = 2
79 retract_layer_change = 1
80 retract_length = 1.3
81 retract_length_toolchange = 3
82 retract_lift = 0
83 retract_restart_extra = 0
84 retract_restart_extra_toolchange = 0
85 retract_speed = 60
86 seam_position = aligned
87 skirt_distance = 10
88 skirt_height = 1
89 skirts = 1
90 slowdown_below_layer_time = 20
91 small_perimeter_speed = 30
92 solid_infill_below_area = 70
93 solid_infill_every_layers = 0
94 solid_infill_extruder = 1
95 solid_infill_extrusion_width = 0
96 solid_infill_speed = 55
97 spiral_vase = 0
98 standby_temperature_delta = -5
99 start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
100 support_material = 0
101 support_material_angle = 0
102 support_material_contact_distance = 0.2
103 support_material_enforce_layers = 0
104 support_material_extruder = 1
105 support_material_extrusion_width = 0
106 support_material_interface_extruder = 1
107 support_material_interface_layers = 0
108 support_material_interface_spacing = 0
109 support_material_interface_speed = 100%
110 support_material_pattern = rectilinear
111 support_material_spacing = 2.5
112 support_material_speed = 60
113 support_material_threshold = 0
114 temperature = 225
115 thin_walls = 1
116 threads = 4
117 toolchange_gcode =
118 top_infill_extrusion_width = 0
119 top_solid_infill_speed = 50
120 top_solid_layers = 3
121 travel_speed = 130
122 use_firmware_retraction = 0
123 use_relative_e_distances = 1
124 use_volumetric_e = 0
125 vibration_limit = 0
126 wipe = 0
127 xy_size_compensation = 0
128 z_offset = 0