Rev Author Line No. Line
4625 jacho 1 $fn=40; // model faces resolution.
2 include <../configuration.scad>
3  
4 include <ISLHOLDER01A_D02.scad>
5  
4668 jacho 6  
4625 jacho 7 PI=3.141592;
8  
9 //Držák anemometru
10  
11 module ISLHOLDER01A_D01()
12 {
13 difference()
14 {
15 union()
16 {
17 //výstuha
18 translate([S01_sila_materialu/2,0,0])
19 rotate ([0,-90,0])
20 linear_extrude (height = S01_sila_materialu, convexity = 10)
21 polygon(points=[[D02_vyska_uchytky/2,D01_delka_tyce+S01_prumer_vnitrni/2+D01_material_pred_zavitem+D02_sila_materialu-1],[0, D01_delka_tyce+S01_prumer_vnitrni/2+D01_material_pred_zavitem+D02_sila_materialu-1],[0,S01_prumer_vnitrni/2+D01_material_pred_zavitem],[D02_vyska_uchytky/3,S01_prumer_vnitrni/2+D01_material_pred_zavitem]]);
22  
23 rotate ([90,0,0])
24 translate([0,15,D01_material_pod_zavitem/2-S01_prumer_vnitrni/2-D01_material_pred_zavitem])
25 difference() {
26 cube([D01_sirka_tyce,30,D01_material_pod_zavitem],center=true);
27 translate([0,8,0])
28 cylinder(h=D01_material_pod_zavitem+0.01,r=D02_prumer_uchytneho_sroubu/2,center=true);
29 }
30  
31 //uchyt na tyc
32 translate([0,D01_delka_tyce/2+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2])
33 cube([D01_sirka_tyce,D01_delka_tyce,D01_material_pod_zavitem],center=true);
34  
35 //uchyt na tyc ovalna cast
36 translate([0,(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2])
37 cube([D01_sirka_tyce,D01_material_za_zavitem+D01_material_pred_zavitem,D01_material_pod_zavitem],center=true);
38  
39 //material kolem uchytu na sloupek
40 translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+(D02_sila_materialu+D02_prumer_obruby/2)/2-D02_dotahova_vzdalenost,D01_material_pod_zavitem/2])
41  
42 difference()
43 {
44 cube([D01_sirka_tyce,D02_sila_materialu+D02_prumer_obruby/2,D01_material_pod_zavitem],center=true);
45  
46 translate([0,D02_prumer_obruby/2-D02_dotahova_vzdalenost-D02_sila_materialu,0])
47 cylinder(h=D02_vyska_uchytky+0.01,r=D02_prumer_obruby/2,center=true);
48 }
49  
50 //uchyt na sloupek
51 translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+D02_sila_materialu+(D02_prumer_obruby)/2,D02_vyska_uchytky/2])
52 rotate(a=[0,0,270])
53 ISLHOLDER01A_D02_2();
54  
55 }
56  
57  
58  
59 }
60 }
61  
62 ISLHOLDER01A_D01();
63