Rev Author Line No. Line
2908 kaklik 1 #include "main.h"
2906 jacho 2  
2909 kaklik 3 void SHT25_soft_reset()
2906 jacho 4 {
2909 kaklik 5 i2c_start(); // Start condition
6 i2c_write(0x80); // Device address
7 i2c_write(0xFE); // Device command
8 i2c_stop(); // Stop condition
9 }
2906 jacho 10  
2911 kaklik 11 #define SHT25_HEATER_ON 0x04
12 #define SHT25_HEATER_OFF 0x00
13 #define SHT25_OTP_reload_off 0x02
14 #define SHT25_RH12_T14 0x00
15 #define SHT25_RH8_T12 0x01
16 #define SHT25_RH10_T13 0x80
17 #define SHT25_RH11_T11 0x81
2910 kaklik 18  
2911 kaklik 19 #define SHT25_ADDR 0x80
20  
21 unsigned int8 SHT25_setup(unsigned int8 setup_reg ) // writes to status register and returns its value
2909 kaklik 22 {
23 unsigned int8 reg;
2906 jacho 24  
2909 kaklik 25 i2c_start(); // Start condition
2911 kaklik 26 i2c_write(SHT25_ADDR); // Device address
2909 kaklik 27 i2c_write(0xE7); // Device command
2906 jacho 28  
2909 kaklik 29 i2c_start(); // Start condition
2911 kaklik 30 i2c_write(SHT25_ADDR+1); // Device address
31 reg=i2c_read(0); // Read status actual status register
32  
33 reg = (reg & 0x3A) | setup_reg;
34  
35 i2c_start(); // Start condition
36 i2c_write(SHT25_ADDR); // Device address
37 i2c_write(0xE7); // Write to status register
38 i2c_write(reg); // Device command
2909 kaklik 39 i2c_stop(); // Stop condition
2911 kaklik 40  
41 return (reg);
2909 kaklik 42 }
2906 jacho 43  
2911 kaklik 44  
2909 kaklik 45 float SHT25_get_temp()
46 {
47 unsigned int8 MSB, LSB, Check;
48 unsigned int16 data;
2906 jacho 49  
2909 kaklik 50 i2c_start();
2911 kaklik 51 I2C_Write(SHT25_ADDR);
2909 kaklik 52 I2C_write(0xE3);
2906 jacho 53 i2c_stop();
2909 kaklik 54  
55 delay_ms(100);
2906 jacho 56  
57 i2c_start();
2911 kaklik 58 I2C_Write(SHT25_ADDR+1);
2909 kaklik 59 MSB=i2c_read(1);
60 LSB=i2c_read(1);
61 Check=i2c_read(0);
62 i2c_stop();
63  
64 LSB = LSB >> 2; // trow out status bits
2906 jacho 65  
2909 kaklik 66 data = (((unsigned int16) MSB << 8) + (LSB << 4));
67 return(-46.85 + 175.72*((float)data/0xFFFF));
68 }
69  
70 float SHT25_get_hum()
71 {
72 unsigned int8 MSB, LSB, Check;
73 unsigned int16 data;
74  
75 i2c_start(); //RH
2911 kaklik 76 I2C_Write(SHT25_ADDR);
2909 kaklik 77 I2C_write(0xE5);
78 // i2c_stop();
79  
80 delay_ms(100);
81  
2906 jacho 82 i2c_start();
2911 kaklik 83 I2C_Write(SHT25_ADDR+1);
2909 kaklik 84 MSB=i2c_read(1);
85 LSB=i2c_read(1);
86 Check=i2c_read(0);
87 i2c_stop();
2906 jacho 88  
2909 kaklik 89 // printf("%X %X %X\r\n",MSB, LSB, Check);
2906 jacho 90  
2909 kaklik 91 LSB = LSB >> 2; // trow out status bits
2906 jacho 92  
2909 kaklik 93 data = (((unsigned int16) MSB << 8) + (LSB << 4) );
94 return( -6.0 + 125.0*((float)data/0xFFFF));
95 }
2906 jacho 96  
97  
2909 kaklik 98 void main()
99 {
2911 kaklik 100 unsigned int8 i=0;
2906 jacho 101  
2909 kaklik 102 setup_adc_ports(NO_ANALOGS|VSS_VDD);
103 setup_adc(ADC_CLOCK_DIV_2);
104 setup_spi(SPI_SS_DISABLED);
105 setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1);
106 setup_timer_1(T1_DISABLED);
107 setup_timer_2(T2_DISABLED,0,1);
108 setup_ccp1(CCP_OFF);
109 setup_comparator(NC_NC_NC_NC);
110  
2911 kaklik 111 SHT25_soft_reset();
2909 kaklik 112 printf("SHT25 humidity and temperature sensor example \r\n",);
113 delay_ms (500);
114  
115 while(TRUE)
116 {
2911 kaklik 117 if (i<10)
118 printf("setup: %X \r\n",SHT25_setup(SHT25_RH12_T14 | SHT25_HEATER_OFF));
119 else
120 {
121 printf("setup: %X \r\n",SHT25_setup(SHT25_RH12_T14 | SHT25_HEATER_ON));
122 i = 0;
123 }
2909 kaklik 124 delay_ms (500);
125 printf("Temp: %f \r\n",SHT25_get_temp());
126 delay_ms (500);
127 printf("Hum: %f \r\n",SHT25_get_hum());
128 delay_ms (1000);
2911 kaklik 129 i++;
2909 kaklik 130 }
2906 jacho 131 }
132