| 2012 |
kaklik |
1 |
/* |
| 1754 |
kakl |
2 |
#include <18F4550.h> |
| 1744 |
kakl |
3 |
|
|
|
4 |
#FUSES NOWDT //No Watch Dog Timer |
|
|
5 |
#FUSES WDT128 //Watch Dog Timer uses 1:128 Postscale |
| 1754 |
kakl |
6 |
#FUSES HS //High speed Osc (> 4mhz for PCM/PCH) (>10mhz for PCD) |
|
|
7 |
#FUSES NOPROTECT //Code not protected from reading |
| 1744 |
kakl |
8 |
#FUSES NOBROWNOUT //No brownout reset |
| 1754 |
kakl |
9 |
#FUSES BORV20 //Brownout reset at 2.0V |
|
|
10 |
#FUSES NOPUT //No Power Up Timer |
|
|
11 |
#FUSES NOCPD //No EE protection |
| 1744 |
kakl |
12 |
#FUSES STVREN //Stack full/underflow will cause reset |
|
|
13 |
#FUSES NODEBUG //No Debug mode for ICD |
| 1754 |
kakl |
14 |
#FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
|
|
15 |
#FUSES NOWRT //Program memory not write protected |
|
|
16 |
#FUSES NOWRTD //Data EEPROM not write protected |
|
|
17 |
#FUSES IESO //Internal External Switch Over mode enabled |
|
|
18 |
#FUSES FCMEN //Fail-safe clock monitor enabled |
|
|
19 |
#FUSES PBADEN //PORTB pins are configured as analog input channels on RESET |
|
|
20 |
#FUSES NOWRTC //configuration not registers write protected |
|
|
21 |
#FUSES NOWRTB //Boot block not write protected |
| 1744 |
kakl |
22 |
#FUSES NOEBTR //Memory not protected from table reads |
| 1754 |
kakl |
23 |
#FUSES NOEBTRB //Boot block not protected from table reads |
|
|
24 |
#FUSES NOCPB //No Boot Block code protection |
| 1744 |
kakl |
25 |
#FUSES MCLR //Master Clear pin enabled |
| 1754 |
kakl |
26 |
#FUSES LPT1OSC //Timer1 configured for low-power operation |
|
|
27 |
#FUSES NOXINST //Extended set extension and Indexed Addressing mode disabled (Legacy mode) |
|
|
28 |
#FUSES PLL12 //Divide By 12(48MHz oscillator input) |
|
|
29 |
#FUSES CPUDIV1 //System Clock by 1 |
|
|
30 |
#FUSES USBDIV //USB clock source comes from PLL divide by 2 |
|
|
31 |
#FUSES VREGEN //USB voltage regulator enabled |
|
|
32 |
#FUSES ICPRT //ICPRT enabled |
| 2012 |
kaklik |
33 |
*/ |
| 1744 |
kakl |
34 |
|
| 2012 |
kaklik |
35 |
#include <16F887.h> |
|
|
36 |
#device adc=8 |
|
|
37 |
|
|
|
38 |
#FUSES NOWDT //No Watch Dog Timer |
|
|
39 |
#FUSES HS //Internal RC Osc |
|
|
40 |
#FUSES NOPUT //No Power Up Timer |
|
|
41 |
#FUSES MCLR //Master Clear pin enabled |
|
|
42 |
#FUSES NOPROTECT //Code not protected from reading |
|
|
43 |
#FUSES NOCPD //No EE protection |
|
|
44 |
#FUSES NOBROWNOUT //No brownout reset |
|
|
45 |
#FUSES IESO //Internal External Switch Over mode enabled |
|
|
46 |
#FUSES FCMEN //Fail-safe clock monitor enabled |
|
|
47 |
#FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
|
|
48 |
#FUSES NODEBUG //No Debug mode for ICD |
|
|
49 |
#FUSES NOWRT //Program memory not write protected |
|
|
50 |
#FUSES BORV40 //Brownout reset at 4.0V |
|
|
51 |
|
|
|
52 |
|
|
|
53 |
|
| 1754 |
kakl |
54 |
#use delay(clock=20000000) |
|
|
55 |
#use rs232(baud=9600,parity=N,xmit=PIN_B7,rcv=PIN_B6,bits=8) |
| 1744 |
kakl |
56 |
|
| 1754 |
kakl |
57 |
#define TDC_ENABLE PIN_B3 //enable pin for SPI communication with TDC |
| 1886 |
kakl |
58 |
#use spi(DI=PIN_B1, DO=PIN_B0, CLK=PIN_B2, stream=TDC_stream, bits=32,baud=9600) // uses software SPI |
| 1754 |
kakl |
59 |
|
|
|
60 |
|
|
|
61 |
|