| 1,53 → 1,53 |
|---|
| use <configuration/sloupek.scad> |
| use <configuration/plbase.scad> |
| use <configuration/bocnice.scad> |
| use <configuration/otvory.scad> |
| use <configuration/text/Write.scad> |
| use <upravena_bocnice.scad> |
| |
| include <configuration/manufactury_conf.scad> |
| include <configuration.scad> |
| include <configuration/otvory_conf.scad> |
| |
| |
| barva_sloupku = "cyan"; |
| barva_listy = "red"; |
| barva_celicka = "green"; |
| barva_plbase = "yellow"; |
| |
| //translate([0.5*10.16,-5.08,14]) |
| // cube([10.16,10.16,10.16]); |
| |
| |
| //BOCNICE SE DNEM |
| //------------------------------------------------------------- |
| upravena_bocnice(); |
| |
| |
| |
| |
| |
| //PLBASE HORNI |
| //------------------------------------------------------------- |
| |
| |
| |
| translate([plbase_tolerance_horni-0.2,+plbase_tolerance_horni-0.2,vyska_bocnice/2-tloustka_plbase/2]) |
| rotate(a=[0,0,0]) |
| { |
| |
| |
| //plbase_vrchni_kryt(pocet_der1+2,pocet_der2+2,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice,plbase_tolerance_horni); |
| |
| plbase_vrchni_kryt_pro_odecet(pocet_der1-1,pocet_der2-1,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice,-0.2,tloustka_plbase); |
| } |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| use <configuration/sloupek.scad> |
| use <configuration/plbase.scad> |
| use <configuration/bocnice.scad> |
| use <configuration/otvory.scad> |
| use <configuration/text/Write.scad> |
| use <upravena_bocnice.scad> |
| |
| include <configuration/manufactury_conf.scad> |
| include <configuration.scad> |
| include <configuration/otvory_conf.scad> |
| |
| |
| barva_sloupku = "cyan"; |
| barva_listy = "red"; |
| barva_celicka = "green"; |
| barva_plbase = "yellow"; |
| |
| //translate([0.5*10.16,-5.08,14]) |
| // cube([10.16,10.16,10.16]); |
| |
| |
| //BOCNICE SE DNEM |
| //------------------------------------------------------------- |
| upravena_bocnice(); |
| |
| |
| |
| |
| |
| //PLBASE HORNI |
| //------------------------------------------------------------- |
| |
| |
| |
| translate([plbase_tolerance_horni-0.2,+plbase_tolerance_horni-0.2,vyska_bocnice/2-tloustka_plbase/2]) |
| rotate(a=[0,0,0]) |
| { |
| |
| |
| //plbase_vrchni_kryt(pocet_der1+2,pocet_der2+2,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice,plbase_tolerance_horni); |
| |
| plbase_vrchni_kryt_pro_odecet(pocet_der1-1,pocet_der2-1,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice,-0.2,tloustka_plbase); |
| } |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |