| 0,0 → 1,71 |
|---|
| include <manufactury_conf.scad> |
| include <../configuration.scad> |
| use <MLAB_logo.scad> |
| |
| sloupek (); |
| |
| |
| //Funkce pro generovani sloupku |
| module sloupek() { |
| |
| difference () { |
| translate([-(prumer_matice+2*tloustka_bocnice-2*radidus_hrany)/2,-(prumer_matice+2*tloustka_bocnice-2*radidus_hrany)/2,0]) |
| minkowski() |
| { |
| cube([prumer_matice+2*tloustka_bocnice-2*radidus_hrany,prumer_matice+2*tloustka_bocnice-2*radidus_hrany,vyska_matice+2*tloustka_bocnice]); // base plastics brick |
| cylinder(r=radidus_hrany,h=0.1); |
| } |
| |
| translate([0,0,vyska_matice+2*tloustka_bocnice+0.1-tloustka_bocnice/2+0.2]) |
| cylinder((tloustka_bocnice), d=(prumer_sroubu), center=true); |
| |
| cylinder((vyska_matice+2*tloustka_bocnice), d=(prumer_sroubu), center=true); |
| |
| |
| //otvor na matici |
| translate([0,tloustka_bocnice/2-posuv_dorazu/2,(vyska_matice+2*tloustka_bocnice)/2]) |
| |
| cube([prumer_matice, prumer_matice+posuv_dorazu+tloustka_bocnice,vyska_matice], center = true); |
| |
| } |
| |
| difference () { |
| translate([-(prumer_matice+2*tloustka_bocnice)/2,-(prumer_matice+2*tloustka_bocnice)/2,-vyska_podpery]) |
| rotate([0, 0, 45]) |
| |
| cylinder(vyska_podpery,0,sqrt(2*((prumer_matice+2*tloustka_bocnice)*(prumer_matice+2*tloustka_bocnice))),$fn=4); |
| |
| |
| |
| |
| difference () { |
| |
| |
| |
| translate([-((sqrt(2*((prumer_matice+2*tloustka_bocnice)*(prumer_matice+2*tloustka_bocnice))*2))),-((sqrt(2*((prumer_matice+2*tloustka_bocnice)*(prumer_matice+2*tloustka_bocnice))*2))),-vyska_podpery]) |
| cube([2*(sqrt(2*((prumer_matice+2*tloustka_bocnice)*(prumer_matice+2*tloustka_bocnice))*2)),2*(sqrt(2*((prumer_matice+2*tloustka_bocnice)*(prumer_matice+2*tloustka_bocnice))*2)),vyska_podpery+0.1]); |
| |
| translate([-(prumer_matice+2*tloustka_bocnice-2*radidus_hrany)/2,-(prumer_matice+2*tloustka_bocnice-2*radidus_hrany)/2,-vyska_podpery+0.05]) |
| |
| minkowski() |
| { |
| cube([prumer_matice+2*tloustka_bocnice-2*radidus_hrany,prumer_matice+2*tloustka_bocnice-2*radidus_hrany,vyska_podpery+0.01]); // base plastics brick |
| cylinder(r=radidus_hrany,h=0.1); |
| } |
| } |
| |
| |
| |
| |
| } |
| |
| |
| |
| |
| } |
| |
| |
| |
| |
| |
| |