| 29,6 → 29,8 |
|---|
| void TIMER1_isr(void) |
| { |
| output_toggle(PIN_E0); |
| set_timer1(0); |
| |
| // anemo = ((timer0_overflow_count * 0xFF) + get_timer0())/(32768.0/0xFFFF); |
| // timer0_overflow_count=0; |
| // set_timer0(0); |
| 54,13 → 56,9 |
|---|
| |
| if (REV[strlen(REV)-1]=='$') REV[strlen(REV)-1]=0; |
| printf("\r\n\r\n# AWS01A %s (C) 2013 www.mlab.cz \r\n",VER); // Welcome message |
| restart_wdt(); //---WDT |
| printf("#%s\r\n",&REV[4]); |
| printf("# ver seq temp[mK] hum_temp[mK] hum[%%] "); |
| restart_wdt(); //---WDT |
| printf("bar_temp[mK] pressure[hPa] Anemo[pls/s]check\r\n\r\n"); |
| |
| restart_wdt(); //---WDT |
| } |
| |
| void main() |
| 67,46 → 65,36 |
|---|
| { |
| unsigned int16 seq=0; |
| |
| setup_oscillator(OSC_8MHZ); // pri prouziti bootloaderu neni treba nastavovat |
| setup_wdt(WDT_2304MS); |
| restart_wdt(); //---WDT |
| setup_adc_ports(NO_ANALOGS|VSS_VDD); |
| setup_adc(ADC_CLOCK_DIV_2); |
| //!!! setup_timer_0(RTCC_EXT_L_TO_H|RTCC_DIV_1); |
| // setup_timer_1(T1_INTERNAL|T1_DIV_BY_1|T1_CLK_OUT); |
| setup_timer_0(RTCC_EXT_L_TO_H|RTCC_DIV_1); |
| // setup_timer_1(T1_EXTERNAL|T1_DIV_BY_1);//|T1_CLK_OUT); |
| setup_timer_1(T1_INTERNAL|T1_DIV_BY_8); |
| setup_timer_2(T2_DISABLED,0,1); |
| setup_ccp1(CCP_OFF); |
| setup_comparator(NC_NC_NC_NC); // This device COMP currently not supported by the PICWizard |
| // setup_oscillator(OSC_8MHZ); // pri prouziti bootloaderu neni treba nastavovat |
| // setup_wdt(WDT_2304MS); |
| setup_spi(SPI_MASTER | SPI_MODE_0 | SPI_CLK_DIV_64); |
| output_high(CSN_SPI); |
| |
| // delay_ms(100); |
| |
| welcome(); // welcome print and device indentification |
| output_low(PIN_E1); |
| // delay_ms(100); |
| restart_wdt(); //---WDT |
| |
| // sht_init(); |
| // MPL_init(); // get correction coefficients from the sensor |
| |
| output_low(PIN_E1); |
| |
| enable_interrupts(INT_TIMER1); // interrupts used for anemometer readings |
| //enable_interrupts(INT_TIMER0); |
| // disable_interrupts(INT_RDA); |
| enable_interrupts(GLOBAL); |
| output_high(PIN_E1); |
| |
| restart_wdt(); //---WDT |
| |
| sht_init(); |
| MPL_init(); // get correction coefficients from the sensor |
| |
| output_high(PIN_E1); |
| // delay_ms(200); |
| restart_wdt(); //---WDT |
| while (TRUE) |
| { |
| // output_toggle(PIN_E0); |
| delay_ms(200); |
| restart_wdt(); //---WDT |
| |
| } |
| |
| while (TRUE) |
| { |
| char output[8]; // Output buffer |