Problem with comparison.
/Designs/Measuring_instruments/RMDS02D/CAD/src/connectors_holder.scad |
---|
0,0 → 1,90 |
use<Write.scad> |
$fn=100; |
x_size = 20; // horizontal outer size of the pedestal. |
y_size = 20; // |
mount_hole = 3.5; |
nut_size = 6.8; |
SMA_dia = 6.5; |
SMA_flat = 3.15; |
thickness = 10; // |
wall_thickness = 2; |
height = 55; |
mount_hole = 3.7; |
clear = 0.175; |
MLAB_grid = 10.16; |
x_holes = floor(x_size / MLAB_grid); |
y_holes = floor(y_size / MLAB_grid); |
MLAB_grid_xoffset = (x_size - (x_holes * MLAB_grid))/2; |
MLAB_grid_yoffset = (y_size - (y_holes * MLAB_grid))/2; |
//Top part |
union () { |
difference () { |
cube([x_size, y_size , thickness ]); |
// MLAB grid holes |
grid_list = [for (j = [MLAB_grid_xoffset : MLAB_grid: x_size], i = [MLAB_grid_yoffset :MLAB_grid: y_size]) [j, i] ]; |
for (j = grid_list) { |
translate (concat(j, [0])) |
cylinder (h = 3, r= nut_size/2, $fn=6); |
translate (concat(j, [3.2])) // one solid layer for slicer (the holes will be pierced on demand ) |
cylinder (h = thickness /3, r= mount_hole/2, $fn=30); |
translate (concat(j, [6.0])) |
cylinder (h = 10, r= nut_size/2, $fn=6); |
} |
}; |
difference () { |
translate ([0, -wall_thickness, 0]) // vertical brick |
cube([y_size, wall_thickness , height ]); |
// SMA connector holes |
translate ([ x_size/2, wall_thickness/2, (height - thickness)/3 + thickness - SMA_dia/2]) |
rotate([90,0,0]) { |
difference () { |
cylinder (h = 2*wall_thickness, r= SMA_dia/2, $fn=50); |
translate([ 0, SMA_flat , wall_thickness/2 + wall_thickness ]) |
cube([SMA_dia, 1 , thickness ], center=true); |
} |
} |
translate ([ x_size/2, wall_thickness/2, 2*(height - thickness)/3 + thickness + SMA_dia/2 ]) |
rotate([90,0,0]){ |
difference () { |
cylinder (h = 2*wall_thickness, r= SMA_dia/2, $fn=50); |
translate([ 0, SMA_flat , wall_thickness/2 + wall_thickness ]) |
cube([SMA_dia, 1 , thickness ], center=true); |
} |
} |
// texts |
translate ([ x_size/2, wall_thickness/2, (height - thickness)/3 + thickness - SMA_dia/2]) |
rotate([90,0,0]) { |
translate([ 0, -11, wall_thickness/2 + wall_thickness ]) |
rotate([0,0,180]) |
write("GPS",h=5,t=2,space= 1.1, font = "Letters.dxf", center=true); |
} |
translate ([ x_size/2, wall_thickness/2, 2*(height - thickness)/3 + thickness + SMA_dia/2 ]) |
rotate([90,0,0]){ |
translate([ 0, -11, wall_thickness/2 + wall_thickness]) |
rotate([0,0,180]) |
write("ANT",h=5,t=2, space= 1.1, font = "Letters.dxf",center=true); |
} |
} |
} |