| 1,41 → 1,25 |
|---|
| #include <18F4550.h> |
| #include <18F8310.h> |
| #device adc=8 |
| |
| #FUSES NOWDT //No Watch Dog Timer |
| #FUSES WDT128 //Watch Dog Timer uses 1:128 Postscale |
| #FUSES HS //High speed Osc (> 4mhz for PCM/PCH) (>10mhz for PCD) |
| #FUSES NOPROTECT //Code not protected from reading |
| #FUSES INTRC_IO //Internal RC Osc, no CLKOUT |
| #FUSES NOBROWNOUT //No brownout reset |
| #FUSES BORV20 //Brownout reset at 2.0V |
| #FUSES NOPUT //No Power Up Timer |
| #FUSES NOCPD //No EE protection |
| #FUSES BORV46 //Brownout reset at 4.6V |
| #FUSES PUT //Power Up Timer |
| #FUSES BW16 //16-bit external bus mode |
| #FUSES STVREN //Stack full/underflow will cause reset |
| #FUSES NODEBUG //No Debug mode for ICD |
| #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
| #FUSES NOWRT //Program memory not write protected |
| #FUSES NOWRTD //Data EEPROM not write protected |
| #FUSES IESO //Internal External Switch Over mode enabled |
| #FUSES FCMEN //Fail-safe clock monitor enabled |
| #FUSES PBADEN //PORTB pins are configured as analog input channels on RESET |
| #FUSES NOWRTC //configuration not registers write protected |
| #FUSES NOWRTB //Boot block not write protected |
| #FUSES NOIESO //Internal External Switch Over mode disabled |
| #FUSES NOFCMEN //Fail-safe clock monitor disabled |
| #FUSES NOXINST //Extended set extension and Indexed Addressing mode disabled (Legacy mode) |
| #FUSES NOWAIT //Wait selections unavailable for Table Reads or Table Writes |
| #FUSES NOPROTECT //Code not protected from reading |
| #FUSES NOEBTR //Memory not protected from table reads |
| #FUSES NOEBTRB //Boot block not protected from table reads |
| #FUSES NOCPB //No Boot Block code protection |
| #FUSES NOLPT1OSC //Timer1 configured for higher power operation |
| #FUSES MCLR //Master Clear pin enabled |
| #FUSES LPT1OSC //Timer1 configured for low-power operation |
| #FUSES NOXINST //Extended set extension and Indexed Addressing mode disabled (Legacy mode) |
| #FUSES PLL12 //Divide By 12(48MHz oscillator input) |
| #FUSES CPUDIV1 //System Clock by 1 |
| #FUSES USBDIV //USB clock source comes from PLL divide by 2 |
| #FUSES VREGEN //USB voltage regulator enabled |
| #FUSES ICPRT //ICPRT enabled |
| #FUSES MCU //Microcontroller Mode |
| |
| #use delay(clock=20000000) |
| #use rs232(baud=9600,parity=N,xmit=PIN_B7,rcv=PIN_B6,bits=8) |
| #use delay(clock=1000000) |
| #use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8) |
| |
| #define TDC_ENABLE PIN_B3 //enable pin for SPI communication with TDC |
| #use spi(DI=PIN_B1, DO=PIN_B0, CLK=PIN_B2, stream=TDC_stream, bits=32) // uses software SPI |
| |
| |
| |