Problem with comparison.
| /Modules/ARM/ODROID-U3/CAD/src/slic3r_config_multi_Black_PLA.ini |
|---|
| 0,0 → 1,131 |
| # generated by Slic3r 1.2.9 on Fri Jul 31 23:56:57 2015 |
| avoid_crossing_perimeters = 0 |
| bed_shape = -10x0,190x0,190x200,-10x200 |
| bed_temperature = 50 |
| before_layer_gcode = |
| bottom_solid_layers = 3 |
| bridge_acceleration = 0 |
| bridge_fan_speed = 100 |
| bridge_flow_ratio = 1 |
| bridge_speed = 60 |
| brim_width = 0 |
| complete_objects = 0 |
| cooling = 1 |
| default_acceleration = 0 |
| disable_fan_first_layers = 1 |
| dont_support_bridges = 1 |
| duplicate_distance = 6 |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n |
| external_fill_pattern = rectilinear |
| external_perimeter_extrusion_width = 0 |
| external_perimeter_speed = 50% |
| external_perimeters_first = 0 |
| extra_perimeters = 1 |
| extruder_clearance_height = 20 |
| extruder_clearance_radius = 20 |
| extruder_offset = 0x0 |
| extrusion_axis = E |
| extrusion_multiplier = 1 |
| extrusion_width = 0 |
| fan_always_on = 1 |
| fan_below_layer_time = 60 |
| filament_colour = #FFFFFF |
| filament_diameter = 1.75 |
| fill_angle = 45 |
| fill_density = 15% |
| fill_pattern = honeycomb |
| first_layer_acceleration = 0 |
| first_layer_bed_temperature = 60 |
| first_layer_extrusion_width = 200% |
| first_layer_height = 0.3 |
| first_layer_speed = 30 |
| first_layer_temperature = 210 |
| gap_fill_speed = 20 |
| gcode_arcs = 0 |
| gcode_comments = 0 |
| gcode_flavor = reprap |
| infill_acceleration = 0 |
| infill_every_layers = 1 |
| infill_extruder = 1 |
| infill_extrusion_width = 0 |
| infill_first = 0 |
| infill_only_where_needed = 1 |
| infill_overlap = 15% |
| infill_speed = 80 |
| interface_shells = 0 |
| layer_gcode = |
| layer_height = 0.3 |
| max_fan_speed = 100 |
| max_print_speed = 80 |
| max_volumetric_speed = 0 |
| min_fan_speed = 100 |
| min_print_speed = 10 |
| min_skirt_length = 0 |
| notes = |
| nozzle_diameter = 0.5 |
| octoprint_apikey = 330CC1C393FC4CD08C420E476D472A7E |
| octoprint_host = 192.168.1.25 |
| only_retract_when_crossing_perimeters = 1 |
| ooze_prevention = 0 |
| output_filename_format = [input_filename_base].gcode |
| overhangs = 1 |
| perimeter_acceleration = 0 |
| perimeter_extruder = 1 |
| perimeter_extrusion_width = 0 |
| perimeter_speed = 60 |
| perimeters = 1 |
| post_process = |
| pressure_advance = 0 |
| raft_layers = 0 |
| resolution = 0 |
| retract_before_travel = 2 |
| retract_layer_change = 0 |
| retract_length = 2 |
| retract_length_toolchange = 10 |
| retract_lift = 0 |
| retract_restart_extra = 0 |
| retract_restart_extra_toolchange = 0 |
| retract_speed = 40 |
| seam_position = random |
| skirt_distance = 6 |
| skirt_height = 1 |
| skirts = 3 |
| slowdown_below_layer_time = 30 |
| small_perimeter_speed = 15 |
| solid_infill_below_area = 70 |
| solid_infill_every_layers = 0 |
| solid_infill_extruder = 1 |
| solid_infill_extrusion_width = 0 |
| solid_infill_speed = 20 |
| spiral_vase = 0 |
| standby_temperature_delta = -5 |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n |
| support_material = 0 |
| support_material_angle = 0 |
| support_material_contact_distance = 0.2 |
| support_material_enforce_layers = 0 |
| support_material_extruder = 1 |
| support_material_extrusion_width = 0 |
| support_material_interface_extruder = 1 |
| support_material_interface_layers = 3 |
| support_material_interface_spacing = 0 |
| support_material_interface_speed = 100% |
| support_material_pattern = pillars |
| support_material_spacing = 2.5 |
| support_material_speed = 60 |
| support_material_threshold = 0 |
| temperature = 210 |
| thin_walls = 1 |
| threads = 2 |
| toolchange_gcode = |
| top_infill_extrusion_width = 0 |
| top_solid_infill_speed = 15 |
| top_solid_layers = 3 |
| travel_speed = 130 |
| use_firmware_retraction = 0 |
| use_relative_e_distances = 0 |
| use_volumetric_e = 0 |
| vibration_limit = 0 |
| wipe = 0 |
| xy_size_compensation = 0 |
| z_offset = 0 |
| /Modules/ARM/ODROID-U3/CAD/src/ODROID-U3_MLAB_breakout_frame.scad |
|---|
| 0,0 → 1,156 |
| pedestal_height = 13; |
| mount_hole = 3.5; |
| clear = 0.175; |
| nut_size = 6.6; |
| module ramp(width, depth, height) { |
| angle = atan(height / depth); |
| difference () { |
| cube([width, depth, height]); |
| //color("red") |
| rotate([angle, 0, 0]) |
| translate([-1, 0, 0]) |
| cube([width + 2, depth * 2, height]); |
| } |
| } |
| difference () { |
| // translate ([-1,-16,0]) |
| cube([50,100,pedestal_height]); |
| //mount holes for ODROID U3 |
| translate ([4.5,4.5 + 76, 1]) |
| rotate([0,0,90]) |
| cylinder (h = 6 ,r= nut_size/2 + clear, $fn=6); |
| translate ([4.5,4.5 + 76, 2]) |
| difference () { |
| cylinder (h = pedestal_height, r= mount_hole/2, $fn=10); |
| translate ([-mount_hole/2,-mount_hole/2, 1.2]) |
| rotate([27,0,0]) cube([5,50,5]); |
| }; |
| translate ([4.5 + 41, 4.5 + 76,1]) |
| rotate([0,0,90]) |
| cylinder (h = 6,r= nut_size/2 + clear, $fn=6); |
| translate ([4.5 + 41, 4.5 + 76, 2]) |
| difference () { |
| cylinder (h = pedestal_height, r= mount_hole/2, $fn=10); |
| translate ([-mount_hole/2,-mount_hole/2, 1.2]) |
| rotate([27,0,0]) cube([5,50,5]); |
| }; |
| /// Two holes for other side of ODROID-U3 PCB. |
| translate ([4.5,4.5,0]) |
| cylinder (h = 6, r= (nut_size+clear)/2, $fn=6); |
| translate ([4.5,4.5,6.2]) |
| cylinder (h = pedestal_height, r= 3.6/2, $fn=10); |
| translate ([4.5+41,4.5,0]) |
| cylinder (h = 6, r= (nut_size+clear)/2, $fn=6); |
| translate ([4.5+41,4.5,6.2]) |
| cylinder (h = pedestal_height, r= 3.6/2, $fn=10); |
| // MLAB grid holes |
| for (j = [1 : 3], i = [0 : 0]) { |
| translate ([4.5 + j*10.16, 4.5 + i*10.16,0]) |
| cylinder (h = 3, r= (nut_size+clear)/2, $fn=6); |
| translate ([4.5 + j*10.16, 4.5 + i*10.16, 3.2]) // one solid layer for slicer (the holes will be pierced on demand ) |
| cylinder (h = pedestal_height /3, r= mount_hole/2, $fn=10); |
| translate ([4.5 + j*10.16, 4.5 + i*10.16, 6.3]) |
| cylinder (h = 10, r= nut_size/2, $fn=6); |
| } |
| for (j = [0 : 7], i = [1 : 6]) { |
| translate ([4.5 + j*10.16, 4.5 + i*10.16,0]) |
| cylinder (h = 3, r= (nut_size+clear)/2, $fn=6); |
| translate ([4.5 + j*10.16, 4.5 + i*10.16, 3.2]) // one solid layer for slicer (the holes will be pierced on demand ) |
| cylinder (h = pedestal_height /3, r= mount_hole/2, $fn=10); |
| translate ([4.5 + j*10.16, 4.5 + i*10.16, 6.3]) |
| cylinder (h = 10, r= nut_size/2, $fn=6); |
| } |
| //////////////////////////////////// |
| translate ([4,6, pedestal_height - 4]) // ODROIDs passive components hole. |
| cube([42,27,5]); |
| translate ([13, 2 , pedestal_height - 4]) // two small resistors on botom side. |
| cube([3,3,5]); |
| translate ([22, 30 , pedestal_height - 4]) // USB over voltage protection. |
| cube([21,5,5]); |
| translate ([0, 41 , pedestal_height - 3.5]) // HOLE for ODROD's , SD card and eMMC. |
| cube([48,32,5]); |
| translate ([0, 38.5 , pedestal_height - 4.5]) // HOLE for ODROD's jack connector |
| cube([15,9,5]); |
| translate ([0, 65 , pedestal_height - 3.5]) // HOLE for ODROD's , SD card and eMMC. |
| cube([17,13,5]); |
| //////////////////////////////////////// |
| //// lightening central holes |
| translate ([10,10, 0]) // ODROIDs passive components hole. |
| cube([30,19.5,pedestal_height ]); |
| translate ([10,41, 0]) // ODROIDs passive components hole. |
| cube([30,30,pedestal_height ]); |
| ////// |
| // MLAB electrical adapter part |
| /////// |
| difference () { |
| translate ([8,74.9,pedestal_height - 11]) // Central mount hole |
| cube([34,17.1,pedestal_height - 8.5]); |
| translate ([25,85.78,0]) |
| cylinder (h = 30, r= nut_size*0.7, $fn=20); |
| } |
| translate ([0,84, pedestal_height - 8.5]) // Holes for MLAB's adapter 5V power connector. |
| cube([50,20,20]); |
| translate ([42,84,pedestal_height - 11]) // Holes for MLAB's adapter 5V power connector. |
| cube([34,8,pedestal_height - 8.5]); |
| translate ([8,92,pedestal_height - 11]) // Holes for MLAB's adapter IO connectors. |
| cube([34,8,pedestal_height - 8.5]); |
| translate ([0,74.9, pedestal_height - 8.5]) // Hole for MLAB PCB |
| cube([50,25.1,2]); |
| translate ([7.5,77,pedestal_height - 8.5]) // Hole For connectors above the adapter PCB |
| cube([35.5,17.1,10]); |
| translate ([0,74.9, pedestal_height - 6.5]) |
| ramp(50, 50, 25); |
| /////// Elecrical adapter PCB mount holes |
| translate ([25,85.78,0]) |
| cylinder (h = 3, r= (nut_size+clear)/2, $fn=6); |
| translate ([25,85.78,3.2]) |
| cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10); |
| translate ([4.68,85.78 + 10.16,0]) |
| cylinder (h = 3, r= (nut_size+clear)/2, $fn=6); |
| translate ([4.68,85.78 + 10.16,3.2]) |
| cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10); |
| translate ([45.32,85.78 + 10.16,0]) |
| cylinder (h = 3, r= (nut_size+clear)/2, $fn=6); |
| translate ([45.32,85.78 + 10.16,3.2]) |
| cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10); |
| } |
| /// Support material |
| /* |
| color("Blue",0.5) |
| //translate ([0,74.9, pedestal_height - 8.5]) // Hole for MLAB PCB |
| cube([50,70,30]); |
| */ |
| /Modules/ARM/ODROID-U3/CAD/src/slic3r_config.ini |
|---|
| 0,0 → 1,131 |
| # generated by Slic3r 1.2.9 on Fri Jul 31 16:30:17 2015 |
| avoid_crossing_perimeters = 0 |
| bed_shape = 0x0,200x0,200x200,0x200 |
| bed_temperature = 0 |
| before_layer_gcode = |
| bottom_solid_layers = 3 |
| bridge_acceleration = 0 |
| bridge_fan_speed = 100 |
| bridge_flow_ratio = 1 |
| bridge_speed = 60 |
| brim_width = 0 |
| complete_objects = 0 |
| cooling = 1 |
| default_acceleration = 0 |
| disable_fan_first_layers = 3 |
| dont_support_bridges = 1 |
| duplicate_distance = 6 |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n |
| external_fill_pattern = rectilinear |
| external_perimeter_extrusion_width = 0 |
| external_perimeter_speed = 50% |
| external_perimeters_first = 0 |
| extra_perimeters = 1 |
| extruder_clearance_height = 20 |
| extruder_clearance_radius = 20 |
| extruder_offset = 0x0 |
| extrusion_axis = E |
| extrusion_multiplier = 1 |
| extrusion_width = 0 |
| fan_always_on = 0 |
| fan_below_layer_time = 60 |
| filament_colour = #FFFFFF |
| filament_diameter = 3 |
| fill_angle = 45 |
| fill_density = 20% |
| fill_pattern = honeycomb |
| first_layer_acceleration = 0 |
| first_layer_bed_temperature = 0 |
| first_layer_extrusion_width = 200% |
| first_layer_height = 0.35 |
| first_layer_speed = 30 |
| first_layer_temperature = 210 |
| gap_fill_speed = 20 |
| gcode_arcs = 0 |
| gcode_comments = 0 |
| gcode_flavor = reprap |
| infill_acceleration = 0 |
| infill_every_layers = 1 |
| infill_extruder = 1 |
| infill_extrusion_width = 0 |
| infill_first = 0 |
| infill_only_where_needed = 0 |
| infill_overlap = 15% |
| infill_speed = 80 |
| interface_shells = 0 |
| layer_gcode = |
| layer_height = 0.3 |
| max_fan_speed = 100 |
| max_print_speed = 80 |
| max_volumetric_speed = 0 |
| min_fan_speed = 35 |
| min_print_speed = 10 |
| min_skirt_length = 0 |
| notes = |
| nozzle_diameter = 0.5 |
| octoprint_apikey = |
| octoprint_host = |
| only_retract_when_crossing_perimeters = 1 |
| ooze_prevention = 0 |
| output_filename_format = [input_filename_base].gcode |
| overhangs = 1 |
| perimeter_acceleration = 0 |
| perimeter_extruder = 1 |
| perimeter_extrusion_width = 0 |
| perimeter_speed = 60 |
| perimeters = 3 |
| post_process = |
| pressure_advance = 0 |
| raft_layers = 0 |
| resolution = 0 |
| retract_before_travel = 2 |
| retract_layer_change = 0 |
| retract_length = 2 |
| retract_length_toolchange = 10 |
| retract_lift = 0 |
| retract_restart_extra = 0 |
| retract_restart_extra_toolchange = 0 |
| retract_speed = 40 |
| seam_position = aligned |
| skirt_distance = 6 |
| skirt_height = 1 |
| skirts = 1 |
| slowdown_below_layer_time = 5 |
| small_perimeter_speed = 15 |
| solid_infill_below_area = 70 |
| solid_infill_every_layers = 0 |
| solid_infill_extruder = 1 |
| solid_infill_extrusion_width = 0 |
| solid_infill_speed = 20 |
| spiral_vase = 0 |
| standby_temperature_delta = -5 |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n |
| support_material = 0 |
| support_material_angle = 0 |
| support_material_contact_distance = 0.2 |
| support_material_enforce_layers = 0 |
| support_material_extruder = 1 |
| support_material_extrusion_width = 0 |
| support_material_interface_extruder = 1 |
| support_material_interface_layers = 3 |
| support_material_interface_spacing = 0 |
| support_material_interface_speed = 100% |
| support_material_pattern = pillars |
| support_material_spacing = 2.5 |
| support_material_speed = 60 |
| support_material_threshold = 0 |
| temperature = 210 |
| thin_walls = 1 |
| threads = 2 |
| toolchange_gcode = |
| top_infill_extrusion_width = 0 |
| top_solid_infill_speed = 15 |
| top_solid_layers = 3 |
| travel_speed = 130 |
| use_firmware_retraction = 0 |
| use_relative_e_distances = 0 |
| use_volumetric_e = 0 |
| vibration_limit = 0 |
| wipe = 0 |
| xy_size_compensation = 0 |
| z_offset = 0 |