/Modules/ARM/ODROID-U3/CAD/src/ODROID-U3_MLAB_breakout_frame.scad
1,156 → 1,156
 
pedestal_height = 13;
mount_hole = 3.5;
clear = 0.175;
nut_size = 6.6;
 
module ramp(width, depth, height) {
angle = atan(height / depth);
difference () {
cube([width, depth, height]);
//color("red")
rotate([angle, 0, 0])
translate([-1, 0, 0])
cube([width + 2, depth * 2, height]);
}
}
 
 
 
difference () {
// translate ([-1,-16,0])
cube([50,100,pedestal_height]);
 
//mount holes for ODROID U3
translate ([4.5,4.5 + 76, 1])
rotate([0,0,90])
cylinder (h = 6 ,r= nut_size/2 + clear, $fn=6);
translate ([4.5,4.5 + 76, 2])
difference () {
cylinder (h = pedestal_height, r= mount_hole/2, $fn=10);
translate ([-mount_hole/2,-mount_hole/2, 1.2])
rotate([27,0,0]) cube([5,50,5]);
};
translate ([4.5 + 41, 4.5 + 76,1])
rotate([0,0,90])
cylinder (h = 6,r= nut_size/2 + clear, $fn=6);
translate ([4.5 + 41, 4.5 + 76, 2])
difference () {
cylinder (h = pedestal_height, r= mount_hole/2, $fn=10);
translate ([-mount_hole/2,-mount_hole/2, 1.2])
rotate([27,0,0]) cube([5,50,5]);
};
/// Two holes for other side of ODROID-U3 PCB.
translate ([4.5,4.5,0])
cylinder (h = 6, r= (nut_size+clear)/2, $fn=6);
translate ([4.5,4.5,6.2])
cylinder (h = pedestal_height, r= mount_hole/2, $fn=10);
translate ([4.5+41,4.5,0])
cylinder (h = 6, r= (nut_size+clear)/2, $fn=6);
translate ([4.5+41,4.5,6.2])
cylinder (h = pedestal_height, r= mount_hole/2, $fn=10);
 
// MLAB grid holes
 
for (j = [1 : 3], i = [0 : 0]) {
translate ([4.5 + j*10.16, 4.5 + i*10.16,0])
cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
translate ([4.5 + j*10.16, 4.5 + i*10.16, 3.2]) // one solid layer for slicer (the holes will be pierced on demand )
cylinder (h = pedestal_height /3, r= mount_hole/2, $fn=10);
translate ([4.5 + j*10.16, 4.5 + i*10.16, 6.3])
cylinder (h = 10, r= nut_size/2, $fn=6);
}
 
 
for (j = [0 : 7], i = [1 : 6]) {
translate ([4.5 + j*10.16, 4.5 + i*10.16,0])
cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
translate ([4.5 + j*10.16, 4.5 + i*10.16, 3.2]) // one solid layer for slicer (the holes will be pierced on demand )
cylinder (h = pedestal_height /3, r= mount_hole/2, $fn=10);
translate ([4.5 + j*10.16, 4.5 + i*10.16, 6.3])
cylinder (h = 10, r= nut_size/2, $fn=6);
}
 
////////////////////////////////////
translate ([4,6, pedestal_height - 4]) // ODROIDs passive components hole.
cube([42,27,5]);
translate ([13, 2 , pedestal_height - 4]) // two small resistors on botom side.
cube([3,3,5]);
translate ([22, 30 , pedestal_height - 4]) // USB over voltage protection.
cube([21,5,5]);
translate ([0, 41 , pedestal_height - 3.5]) // HOLE for ODROD's , SD card and eMMC.
cube([48,32,5]);
translate ([0, 38.5 , pedestal_height - 4.5]) // HOLE for ODROD's jack connector
cube([14,8,5]);
translate ([0, 65 , pedestal_height - 3.5]) // HOLE for ODROD's , SD card and eMMC.
cube([17,13,5]);
 
////////////////////////////////////////
//// lightening central holes
translate ([10,10, 0]) // ODROIDs passive components hole.
cube([30,19.5,pedestal_height ]);
translate ([10,41, 0]) // ODROIDs passive components hole.
cube([30,30,pedestal_height ]);
//////
// MLAB electrical adapter part
///////
difference () {
translate ([8,74.9,pedestal_height - 11]) // Central mount hole
cube([34,17.1,pedestal_height - 8.5]);
translate ([25,85.78,0])
cylinder (h = 30, r= nut_size*0.7, $fn=20);
}
 
translate ([0,84, pedestal_height - 8.5]) // Holes for MLAB's adapter 5V power connector.
cube([50,20,20]);
 
translate ([42,84,pedestal_height - 11]) // Holes for MLAB's adapter 5V power connector.
cube([34,8,pedestal_height - 8.5]);
 
translate ([8,92,pedestal_height - 11]) // Holes for MLAB's adapter IO connectors.
cube([34,8,pedestal_height - 8.5]);
 
translate ([0,74.9, pedestal_height - 8.5]) // Hole for MLAB PCB
cube([50,25.1,2]);
translate ([7.5,77,pedestal_height - 8.5]) // Hole For connectors above the adapter PCB
cube([35.5,17.1,10]);
 
translate ([0,74.9, pedestal_height - 6.5])
ramp(50, 50, 25);
/////// Elecrical adapter PCB mount holes
 
translate ([25,85.78,0])
cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
translate ([25,85.78,3.2])
cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10);
 
translate ([4.68,85.78 + 10.16,0])
cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
translate ([4.68,85.78 + 10.16,3.2])
cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10);
 
translate ([45.32,85.78 + 10.16,0])
cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
translate ([45.32,85.78 + 10.16,3.2])
cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10);
 
}
 
/// Support material
/*
color("Blue",0.5)
//translate ([0,74.9, pedestal_height - 8.5]) // Hole for MLAB PCB
cube([50,70,30]);
 
pedestal_height = 13;
mount_hole = 3.5;
clear = 0.175;
nut_size = 6.6;
 
module ramp(width, depth, height) {
angle = atan(height / depth);
difference () {
cube([width, depth, height]);
//color("red")
rotate([angle, 0, 0])
translate([-1, 0, 0])
cube([width + 2, depth * 2, height]);
}
}
 
 
 
difference () {
// translate ([-1,-16,0])
cube([50,100,pedestal_height]);
 
//mount holes for ODROID U3
translate ([4.5,4.5 + 76, 1])
rotate([0,0,90])
cylinder (h = 6 ,r= nut_size/2 + clear, $fn=6);
translate ([4.5,4.5 + 76, 2])
difference () {
cylinder (h = pedestal_height, r= mount_hole/2, $fn=10);
translate ([-mount_hole/2,-mount_hole/2, 1.2])
rotate([27,0,0]) cube([5,50,5]);
};
translate ([4.5 + 41, 4.5 + 76,1])
rotate([0,0,90])
cylinder (h = 6,r= nut_size/2 + clear, $fn=6);
translate ([4.5 + 41, 4.5 + 76, 2])
difference () {
cylinder (h = pedestal_height, r= mount_hole/2, $fn=10);
translate ([-mount_hole/2,-mount_hole/2, 1.2])
rotate([27,0,0]) cube([5,50,5]);
};
/// Two holes for other side of ODROID-U3 PCB.
translate ([4.5,4.5,0])
cylinder (h = 6, r= (nut_size+clear)/2, $fn=6);
translate ([4.5,4.5,6.2])
cylinder (h = pedestal_height, r= 3.6/2, $fn=10);
translate ([4.5+41,4.5,0])
cylinder (h = 6, r= (nut_size+clear)/2, $fn=6);
translate ([4.5+41,4.5,6.2])
cylinder (h = pedestal_height, r= 3.6/2, $fn=10);
 
// MLAB grid holes
 
for (j = [1 : 3], i = [0 : 0]) {
translate ([4.5 + j*10.16, 4.5 + i*10.16,0])
cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
translate ([4.5 + j*10.16, 4.5 + i*10.16, 3.2]) // one solid layer for slicer (the holes will be pierced on demand )
cylinder (h = pedestal_height /3, r= mount_hole/2, $fn=10);
translate ([4.5 + j*10.16, 4.5 + i*10.16, 6.3])
cylinder (h = 10, r= nut_size/2, $fn=6);
}
 
 
for (j = [0 : 7], i = [1 : 6]) {
translate ([4.5 + j*10.16, 4.5 + i*10.16,0])
cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
translate ([4.5 + j*10.16, 4.5 + i*10.16, 3.2]) // one solid layer for slicer (the holes will be pierced on demand )
cylinder (h = pedestal_height /3, r= mount_hole/2, $fn=10);
translate ([4.5 + j*10.16, 4.5 + i*10.16, 6.3])
cylinder (h = 10, r= nut_size/2, $fn=6);
}
 
////////////////////////////////////
translate ([4,6, pedestal_height - 4]) // ODROIDs passive components hole.
cube([42,27,5]);
translate ([13, 2 , pedestal_height - 4]) // two small resistors on botom side.
cube([3,3,5]);
translate ([22, 30 , pedestal_height - 4]) // USB over voltage protection.
cube([21,5,5]);
translate ([0, 41 , pedestal_height - 3.5]) // HOLE for ODROD's , SD card and eMMC.
cube([48,32,5]);
translate ([0, 38.5 , pedestal_height - 4.5]) // HOLE for ODROD's jack connector
cube([15,9,5]);
translate ([0, 65 , pedestal_height - 3.5]) // HOLE for ODROD's , SD card and eMMC.
cube([17,13,5]);
 
////////////////////////////////////////
//// lightening central holes
translate ([10,10, 0]) // ODROIDs passive components hole.
cube([30,19.5,pedestal_height ]);
translate ([10,41, 0]) // ODROIDs passive components hole.
cube([30,30,pedestal_height ]);
//////
// MLAB electrical adapter part
///////
difference () {
translate ([8,74.9,pedestal_height - 11]) // Central mount hole
cube([34,17.1,pedestal_height - 8.5]);
translate ([25,85.78,0])
cylinder (h = 30, r= nut_size*0.7, $fn=20);
}
 
translate ([0,84, pedestal_height - 8.5]) // Holes for MLAB's adapter 5V power connector.
cube([50,20,20]);
 
translate ([42,84,pedestal_height - 11]) // Holes for MLAB's adapter 5V power connector.
cube([34,8,pedestal_height - 8.5]);
 
translate ([8,92,pedestal_height - 11]) // Holes for MLAB's adapter IO connectors.
cube([34,8,pedestal_height - 8.5]);
 
translate ([0,74.9, pedestal_height - 8.5]) // Hole for MLAB PCB
cube([50,25.1,2]);
translate ([7.5,77,pedestal_height - 8.5]) // Hole For connectors above the adapter PCB
cube([35.5,17.1,10]);
 
translate ([0,74.9, pedestal_height - 6.5])
ramp(50, 50, 25);
/////// Elecrical adapter PCB mount holes
 
translate ([25,85.78,0])
cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
translate ([25,85.78,3.2])
cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10);
 
translate ([4.68,85.78 + 10.16,0])
cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
translate ([4.68,85.78 + 10.16,3.2])
cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10);
 
translate ([45.32,85.78 + 10.16,0])
cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
translate ([45.32,85.78 + 10.16,3.2])
cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10);
 
}
 
/// Support material
/*
color("Blue",0.5)
//translate ([0,74.9, pedestal_height - 8.5]) // Hole for MLAB PCB
cube([50,70,30]);
*/
/Modules/ARM/ODROID-U3/CAD/src/slic3r_config.ini
1,1038 → 1,8
# generated by Slic3r 1.2.7-dev on Fri Mar 20 12:28:23 2015
 
[filament:ABS_1.75]
bed_temperature = 90
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 1.01
fan_always_on = 0
fan_below_layer_time = 1
filament_diameter = 1.75
first_layer_bed_temperature = 90
first_layer_temperature = 225
max_fan_speed = 0
min_fan_speed = 0
min_print_speed = 15
slowdown_below_layer_time = 20
temperature = 225
 
[filament:ABS_1.75 3D factories]
bed_temperature = 90
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 5
filament_diameter = 1.75
first_layer_bed_temperature = 90
first_layer_temperature = 225
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 15
slowdown_below_layer_time = 20
temperature = 225
 
[filament:ABS_1.75 red 3D factories]
bed_temperature = 90
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 5
filament_diameter = 1.73
first_layer_bed_temperature = 80
first_layer_temperature = 230
max_fan_speed = 60
min_fan_speed = 0
min_print_speed = 15
slowdown_below_layer_time = 20
temperature = 225
 
[filament:PLA_1.75]
# generated by Slic3r 1.2.9 on Fri Jul 31 16:30:17 2015
avoid_crossing_perimeters = 0
bed_shape = 0x0,200x0,200x200,0x200
bed_temperature = 0
bridge_fan_speed = 40
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 1
filament_diameter = 1.75
first_layer_bed_temperature = 0
first_layer_temperature = 185
max_fan_speed = 50
min_fan_speed = 40
min_print_speed = 15
slowdown_below_layer_time = 20
temperature = 185
 
[filament:PLA_1.75 3D factories]
bed_temperature = 50
bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 0.9524
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 60
first_layer_temperature = 185
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 185
 
[filament:Simple Mode]
bed_temperature = 110
extrusion_multiplier = 1
filament_diameter = 1.75
first_layer_bed_temperature = 115
first_layer_temperature = 235
temperature = 230
 
[filament:slic3r_config]
bed_temperature = 90
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 0.95
fan_always_on = 0
fan_below_layer_time = 5
filament_diameter = 1.75
first_layer_bed_temperature = 80
first_layer_temperature = 230
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 15
slowdown_below_layer_time = 20
temperature = 230
 
[presets]
filament = slic3r_config.ini
print = 0.2 layer.ini
printer = slic3r_config.ini
 
[print:0.2 layer]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 15
brim_width = 10
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 15%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.2
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 1
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 4
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0
 
[print:0.3 layer]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 10
brim_width = 0
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 25%
fill_pattern = line
first_layer_acceleration = 500
first_layer_extrusion_width = 180%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 10
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0
 
[print:0.3 layer brim]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 3000
bridge_flow_ratio = 1
bridge_speed = 10
brim_width = 10
complete_objects = 0
default_acceleration = 4000
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 25%
fill_pattern = line
first_layer_acceleration = 0
first_layer_extrusion_width = 180%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 15
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0
 
[print:ABS 1.75]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1.9
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 40%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.2
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
 
[print:ABS_rocket]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 500
bridge_flow_ratio = 1.9
bridge_speed = 60
brim_width = 15
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.5
fill_angle = 45
fill_density = 40%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0
 
[print:ABS_vase]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 500
bridge_flow_ratio = 1.9
bridge_speed = 60
brim_width = 5
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 0%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 120%
first_layer_height = 0.3
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 1
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 1
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 0
travel_speed = 130
xy_size_compensation = 0
 
[print:Bridge]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 3000
bridge_flow_ratio = 1
bridge_speed = 10
brim_width = 5
complete_objects = 0
default_acceleration = 4000
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 25%
fill_pattern = line
first_layer_acceleration = 0
first_layer_extrusion_width = 125%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process =
raft_layers = 0
resolution = 0
seam_position = random
skirt_distance = 10
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 100
 
[print:Simple Mode]
bottom_solid_layers = 3
brim_width = 0
complete_objects = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
fill_density = 40%
fill_pattern = honeycomb
infill_speed = 60
layer_height = 0.2
perimeter_speed = 30
perimeters = 3
raft_layers = 0
support_material = 0
support_material_spacing = 2.5
top_solid_layers = 3
travel_speed = 130
 
[print:Standard]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 20
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 25%
fill_pattern = line
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 4
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
 
[print:Weather_screen]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 3000
bridge_flow_ratio = 1
bridge_speed = 10
brim_width = 5
complete_objects = 0
default_acceleration = 4000
dont_support_bridges = 1
external_fill_pattern = concentric
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 90%
fill_pattern = concentric
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 5
skirt_height = 1
skirts = 0
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
 
[print:slic3r_config]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 10
brim_width = 10
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 15%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 10
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0
 
[printer:RebeliX]
bed_shape = 0x0,180x0,180x180,0x180
before_layer_gcode =
end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.4
octoprint_apikey = B14197D3716442D4B0BB8F485877E31E
octoprint_host = 192.168.1.106:5000
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1.3
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 60
start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
z_offset = 0
 
[printer:Simple Mode]
bed_shape = 0x0,180x0,180x180,0x180
end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
gcode_flavor = reprap
nozzle_diameter = 0.3
retract_length = 1
retract_lift = 0
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
z_offset = 0
 
[printer:slic3r_config]
bed_shape = 0x0,180x0,180x180,0x180
before_layer_gcode =
end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.4
octoprint_apikey = B14197D3716442D4B0BB8F485877E31E
octoprint_host = 192.168.1.106:5000
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1.3
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 60
start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
z_offset = 0
 
[settings]
autocenter = 1
mode = expert
 
[simple]
avoid_crossing_perimeters = 1
bed_shape = 0x0,180x0,180x180,0x180
bed_temperature = 110
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
1042,12 → 12,13
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
disable_fan_first_layers = 3
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
external_fill_pattern = rectilinear
external_perimeter_speed = 70%
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
1058,36 → 29,42
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
filament_colour = #FFFFFF
filament_diameter = 3
fill_angle = 45
fill_density = 40%
fill_density = 20%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 115
first_layer_bed_temperature = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 30%
first_layer_temperature = 235
first_layer_height = 0.35
first_layer_speed = 30
first_layer_temperature = 210
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 10
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
infill_overlap = 15%
infill_speed = 80
interface_shells = 0
layer_gcode =
layer_height = 0.2
layer_height = 0.3
max_fan_speed = 100
max_print_speed = 80
max_volumetric_speed = 0
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes =
nozzle_diameter = 0.3
nozzle_diameter = 0.5
octoprint_apikey =
octoprint_host =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
1095,34 → 72,37
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeter_speed = 60
perimeters = 3
post_process =
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_layer_change = 0
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
retract_speed = 40
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 30
slowdown_below_layer_time = 5
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 60
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
1134,16 → 114,18
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
temperature = 230
temperature = 210
thin_walls = 1
threads = 2
toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_infill_speed = 15
top_solid_layers = 3
travel_speed = 130
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0