Problem with comparison.
/Modules/ARM/ODroid-X2/CAD/src/slic3r_config.ini |
---|
0,0 → 1,128 |
# generated by Slic3r 1.2.6 on Fri Feb 6 10:55:50 2015 |
avoid_crossing_perimeters = 0 |
bed_shape = 0x0,180x0,180x180,0x180 |
bed_temperature = 90 |
before_layer_gcode = |
bottom_solid_layers = 3 |
bridge_acceleration = 1000 |
bridge_fan_speed = 0 |
bridge_flow_ratio = 1 |
bridge_speed = 10 |
brim_width = 10 |
complete_objects = 0 |
cooling = 1 |
default_acceleration = 500 |
disable_fan_first_layers = 0 |
dont_support_bridges = 1 |
duplicate_distance = 6 |
end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n |
external_fill_pattern = rectilinear |
external_perimeter_extrusion_width = 0 |
external_perimeter_speed = 90% |
external_perimeters_first = 0 |
extra_perimeters = 1 |
extruder_clearance_height = 20 |
extruder_clearance_radius = 20 |
extruder_offset = 0x0 |
extrusion_axis = E |
extrusion_multiplier = 1 |
extrusion_width = 0 |
fan_always_on = 0 |
fan_below_layer_time = 5 |
filament_diameter = 1.75 |
fill_angle = 45 |
fill_density = 25% |
fill_pattern = line |
first_layer_acceleration = 500 |
first_layer_bed_temperature = 90 |
first_layer_extrusion_width = 200% |
first_layer_height = 0.3 |
first_layer_speed = 60% |
first_layer_temperature = 225 |
gap_fill_speed = 20 |
gcode_arcs = 0 |
gcode_comments = 0 |
gcode_flavor = reprap |
infill_acceleration = 500 |
infill_every_layers = 1 |
infill_extruder = 1 |
infill_extrusion_width = 0 |
infill_first = 0 |
infill_only_where_needed = 0 |
infill_overlap = 15% |
infill_speed = 60 |
interface_shells = 0 |
layer_gcode = |
layer_height = 0.3 |
max_fan_speed = 100 |
min_fan_speed = 50 |
min_print_speed = 15 |
min_skirt_length = 0 |
notes = |
nozzle_diameter = 0.4 |
octoprint_apikey = B14197D3716442D4B0BB8F485877E31E |
octoprint_host = 192.168.1.106:5000 |
only_retract_when_crossing_perimeters = 1 |
ooze_prevention = 0 |
output_filename_format = [input_filename_base].gcode |
overhangs = 1 |
perimeter_acceleration = 500 |
perimeter_extruder = 1 |
perimeter_extrusion_width = 0 |
perimeter_speed = 45 |
perimeters = 2 |
post_process = |
pressure_advance = 0 |
raft_layers = 0 |
resolution = 0 |
retract_before_travel = 2 |
retract_layer_change = 1 |
retract_length = 1.3 |
retract_length_toolchange = 3 |
retract_lift = 0 |
retract_restart_extra = 0 |
retract_restart_extra_toolchange = 0 |
retract_speed = 60 |
seam_position = aligned |
skirt_distance = 10 |
skirt_height = 1 |
skirts = 1 |
slowdown_below_layer_time = 20 |
small_perimeter_speed = 30 |
solid_infill_below_area = 70 |
solid_infill_every_layers = 0 |
solid_infill_extruder = 1 |
solid_infill_extrusion_width = 0 |
solid_infill_speed = 55 |
spiral_vase = 0 |
standby_temperature_delta = -5 |
start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder |
support_material = 0 |
support_material_angle = 0 |
support_material_contact_distance = 0.2 |
support_material_enforce_layers = 0 |
support_material_extruder = 1 |
support_material_extrusion_width = 0 |
support_material_interface_extruder = 1 |
support_material_interface_layers = 0 |
support_material_interface_spacing = 0 |
support_material_interface_speed = 100% |
support_material_pattern = rectilinear |
support_material_spacing = 2.5 |
support_material_speed = 60 |
support_material_threshold = 0 |
temperature = 225 |
thin_walls = 1 |
threads = 4 |
toolchange_gcode = |
top_infill_extrusion_width = 0 |
top_solid_infill_speed = 50 |
top_solid_layers = 3 |
travel_speed = 130 |
use_firmware_retraction = 0 |
use_relative_e_distances = 1 |
use_volumetric_e = 0 |
vibration_limit = 0 |
wipe = 0 |
xy_size_compensation = 0 |
z_offset = 0 |