| 0,0 → 1,259 |
|---|
| [profile] |
| layer_height = 0.3 |
| wall_thickness = 0.8 |
| retraction_enable = True |
| solid_layer_thickness = 0.6 |
| fill_density = 25 |
| nozzle_size = 0.4 |
| print_speed = 50 |
| print_temperature = 212 |
| print_temperature2 = 0 |
| print_temperature3 = 0 |
| print_temperature4 = 0 |
| print_temperature5 = 0 |
| print_bed_temperature = 55 |
| support = None |
| platform_adhesion = None |
| support_dual_extrusion = Both |
| wipe_tower = False |
| wipe_tower_volume = 15 |
| ooze_shield = False |
| filament_diameter = 1,75 |
| filament_diameter2 = 0 |
| filament_diameter3 = 0 |
| filament_diameter4 = 0 |
| filament_diameter5 = 0 |
| filament_flow = 100.0 |
| retraction_speed = 40.0 |
| retraction_amount = 4.5 |
| retraction_dual_amount = 16.5 |
| retraction_min_travel = 1.5 |
| retraction_combing = All |
| retraction_minimal_extrusion = 0.02 |
| retraction_hop = 0.0 |
| bottom_thickness = 0.3 |
| layer0_width_factor = 200 |
| object_sink = 0.0 |
| overlap_dual = 0.15 |
| travel_speed = 100 |
| bottom_layer_speed = 20 |
| infill_speed = 0.0 |
| solidarea_speed = 0.0 |
| inset0_speed = 0.0 |
| insetx_speed = 0.0 |
| cool_min_layer_time = 10 |
| fan_enabled = True |
| skirt_line_count = 1 |
| skirt_gap = 3.0 |
| skirt_minimal_length = 150.0 |
| fan_full_height = 5.0 |
| fan_speed = 100 |
| fan_speed_max = 100 |
| cool_min_feedrate = 10 |
| cool_head_lift = False |
| solid_top = True |
| solid_bottom = True |
| fill_overlap = 15 |
| perimeter_before_infill = True |
| support_type = Lines |
| support_angle = 60 |
| support_fill_rate = 15 |
| support_xy_distance = 0.7 |
| support_z_distance = 0.15 |
| spiralize = False |
| simple_mode = False |
| brim_line_count = 20 |
| raft_margin = 5.0 |
| raft_line_spacing = 3.0 |
| raft_base_thickness = 0.3 |
| raft_base_linewidth = 1.0 |
| raft_interface_thickness = 0.27 |
| raft_interface_linewidth = 0.4 |
| raft_airgap_all = 0.0 |
| raft_airgap = 0.22 |
| raft_surface_layers = 4 |
| raft_surface_thickness = 0.27 |
| raft_surface_linewidth = 0.4 |
| fix_horrible_union_all_type_a = True |
| fix_horrible_union_all_type_b = False |
| fix_horrible_use_open_bits = False |
| fix_horrible_extensive_stitching = False |
| plugin_config = (lp1 |
| . |
| object_center_x = -1 |
| object_center_y = -1 |
| |
| [alterations] |
| start.gcode = ;Sliced at: {day} {date} {time} |
| ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} |
| ;Print time: {print_time} |
| ;Filament used: {filament_amount}m {filament_weight}g |
| ;Filament cost: {filament_cost} |
| ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line |
| ;M109 S{print_temperature} ;Uncomment to add your own temperature line |
| G21 ;metric values |
| G90 ;absolute positioning |
| M82 ;set extruder to absolute mode |
| M107 ;start with the fan off |
| G28 X0 Y0 ;move X/Y to min endstops |
| G28 Z0 ;move Z to min endstops |
| G1 Z15.0 F{travel_speed} ;move the platform down 15mm |
| G92 E0 ;zero the extruded length |
| G1 F200 E3 ;extrude 3mm of feed stock |
| G92 E0 ;zero the extruded length again |
| G1 F{travel_speed} |
| ;Put printing message on LCD screen |
| M117 Printing... |
| end.gcode = ;End GCode |
| M104 S0 ;extruder heater off |
| M140 S0 ;heated bed heater off (if you have it) |
| G91 ;relative positioning |
| G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure |
| G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more |
| G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way |
| M84 ;steppers off |
| G90 ;absolute positioning |
| ;{profile_string} |
| start2.gcode = ;Sliced at: {day} {date} {time} |
| ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} |
| ;Print time: {print_time} |
| ;Filament used: {filament_amount}m {filament_weight}g |
| ;Filament cost: {filament_cost} |
| ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line |
| ;M104 S{print_temperature} ;Uncomment to add your own temperature line |
| ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line |
| ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line |
| G21 ;metric values |
| G90 ;absolute positioning |
| M107 ;start with the fan off |
| G28 X0 Y0 ;move X/Y to min endstops |
| G28 Z0 ;move Z to min endstops |
| G1 Z15.0 F{travel_speed} ;move the platform down 15mm |
| T1 ;Switch to the 2nd extruder |
| G92 E0 ;zero the extruded length |
| G1 F200 E10 ;extrude 10mm of feed stock |
| G92 E0 ;zero the extruded length again |
| G1 F200 E-{retraction_dual_amount} |
| T0 ;Switch to the first extruder |
| G92 E0 ;zero the extruded length |
| G1 F200 E10 ;extrude 10mm of feed stock |
| G92 E0 ;zero the extruded length again |
| G1 F{travel_speed} |
| ;Put printing message on LCD screen |
| M117 Printing... |
| end2.gcode = ;End GCode |
| M104 T0 S0 ;extruder heater off |
| M104 T1 S0 ;extruder heater off |
| M140 S0 ;heated bed heater off (if you have it) |
| G91 ;relative positioning |
| G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure |
| G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more |
| G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way |
| M84 ;steppers off |
| G90 ;absolute positioning |
| ;{profile_string} |
| start3.gcode = ;Sliced at: {day} {date} {time} |
| ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} |
| ;Print time: {print_time} |
| ;Filament used: {filament_amount}m {filament_weight}g |
| ;Filament cost: {filament_cost} |
| ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line |
| ;M104 S{print_temperature} ;Uncomment to add your own temperature line |
| ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line |
| ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line |
| G21 ;metric values |
| G90 ;absolute positioning |
| M107 ;start with the fan off |
| G28 X0 Y0 ;move X/Y to min endstops |
| G28 Z0 ;move Z to min endstops |
| G1 Z15.0 F{travel_speed} ;move the platform down 15mm |
| T2 ;Switch to the 3rd extruder |
| G92 E0 ;zero the extruded length |
| G1 F200 E10 ;extrude 10mm of feed stock |
| G92 E0 ;zero the extruded length again |
| G1 F200 E-{retraction_dual_amount} |
| T1 ;Switch to the 2nd extruder |
| G92 E0 ;zero the extruded length |
| G1 F200 E10 ;extrude 10mm of feed stock |
| G92 E0 ;zero the extruded length again |
| G1 F200 E-{retraction_dual_amount} |
| T0 ;Switch to the first extruder |
| G92 E0 ;zero the extruded length |
| G1 F200 E10 ;extrude 10mm of feed stock |
| G92 E0 ;zero the extruded length again |
| G1 F{travel_speed} |
| ;Put printing message on LCD screen |
| M117 Printing... |
| end3.gcode = ;End GCode |
| M104 T0 S0 ;extruder heater off |
| M104 T1 S0 ;extruder heater off |
| M104 T2 S0 ;extruder heater off |
| M140 S0 ;heated bed heater off (if you have it) |
| G91 ;relative positioning |
| G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure |
| G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more |
| G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way |
| M84 ;steppers off |
| G90 ;absolute positioning |
| ;{profile_string} |
| start4.gcode = ;Sliced at: {day} {date} {time} |
| ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} |
| ;Print time: {print_time} |
| ;Filament used: {filament_amount}m {filament_weight}g |
| ;Filament cost: {filament_cost} |
| ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line |
| ;M104 S{print_temperature} ;Uncomment to add your own temperature line |
| ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line |
| ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line |
| ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line |
| G21 ;metric values |
| G90 ;absolute positioning |
| M107 ;start with the fan off |
| G28 X0 Y0 ;move X/Y to min endstops |
| G28 Z0 ;move Z to min endstops |
| G1 Z15.0 F{travel_speed} ;move the platform down 15mm |
| T3 ;Switch to the 4th extruder |
| G92 E0 ;zero the extruded length |
| G1 F200 E10 ;extrude 10mm of feed stock |
| G92 E0 ;zero the extruded length again |
| G1 F200 E-{retraction_dual_amount} |
| T2 ;Switch to the 3rd extruder |
| G92 E0 ;zero the extruded length |
| G1 F200 E10 ;extrude 10mm of feed stock |
| G92 E0 ;zero the extruded length again |
| G1 F200 E-{retraction_dual_amount} |
| T1 ;Switch to the 2nd extruder |
| G92 E0 ;zero the extruded length |
| G1 F200 E10 ;extrude 10mm of feed stock |
| G92 E0 ;zero the extruded length again |
| G1 F200 E-{retraction_dual_amount} |
| T0 ;Switch to the first extruder |
| G92 E0 ;zero the extruded length |
| G1 F200 E10 ;extrude 10mm of feed stock |
| G92 E0 ;zero the extruded length again |
| G1 F{travel_speed} |
| ;Put printing message on LCD screen |
| M117 Printing... |
| end4.gcode = ;End GCode |
| M104 T0 S0 ;extruder heater off |
| M104 T1 S0 ;extruder heater off |
| M104 T2 S0 ;extruder heater off |
| M104 T3 S0 ;extruder heater off |
| M140 S0 ;heated bed heater off (if you have it) |
| G91 ;relative positioning |
| G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure |
| G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more |
| G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way |
| M84 ;steppers off |
| G90 ;absolute positioning |
| ;{profile_string} |
| support_start.gcode = |
| support_end.gcode = |
| cool_start.gcode = |
| cool_end.gcode = |
| replace.csv = |
| preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. |
| ;This code is added before the T(n) |
| postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. |
| ;This code is added after the T(n) |
| |