| 0,0 → 1,254 |
|---|
| # This configuration file demonstrates panelizing multiple, different jobs. |
| # We panelize the HEXAPOD job and several copies of the Proj1 job. |
| |
| ############################################################################## |
| # In the [DEFAULT] section you can create global names to save typing the same |
| # directory name, for example, over and over. |
| ############################################################################## |
| [DEFAULT] |
| |
| # Change projdir to wherever your project files are, for example: |
| # |
| # projdir = /home/stuff/projects/test |
| # |
| # or relative pathname from where you are running GerbMerge |
| # |
| # projdir = testdata |
| # |
| # or if all files are in the current directory (as in this example): |
| # |
| # projdir = . |
| projdir = . |
| |
| # For convenience, this is the base name of the merged output files. |
| MergeOut = SET11A |
| |
| ############################################################################# |
| # The [Options] section defines settings that control how the input files are |
| # read and how the output files are generated. |
| ############################################################################# |
| [Options] |
| |
| ################################################################ |
| # |
| # Settings that are very important |
| # |
| ################################################################ |
| |
| # Option indicating name of file that maps Excellon tool codes to drill sizes. |
| # This is not necessary if the Excellon files have embedded tool sizes, or if a |
| # tool list is specified as part of the job description. The ToolList option |
| # here is the "last resort" for mapping tool codes to tool sizes. Most recent |
| # PCB programs embed drill size information right in the Excellon file, so this |
| # option should not be necessary and can be commented out. |
| #ToolList=proj1.drl |
| |
| MeasurementUnits = mm |
| KicadFilesInMetricUnits = 1 |
| |
| # Optional indication of the number of decimal places in input Excellon drill |
| # files. The default is 4 which works for recent versions of Eagle (since |
| # version 4.11r12), as well as Orcad and PCB. Older versions of Eagle use 3 |
| # decimal places. |
| ExcellonDecimals = 3 |
| |
| ################################################################ |
| # |
| # Settings that are somewhat important |
| # |
| ################################################################ |
| |
| # Which layers to draw cut lines on. Omit this option or set to 'None' for no |
| # cut lines. Cut lines are borders around each job that serve as guides for |
| # cutting the panel into individual jobs. Option 'CutLineWidth' sets the |
| # thickness of these cut lines. |
| # |
| # NOTE: Layer names are ALL LOWERCASE, even if you define them with uppercase |
| # letters below. |
| CutLineLayers = *topsilkscreen,*bottomsilkscreen |
| |
| # Which layers to draw crop marks on. Omit this option or set to 'None' for no |
| # crop marks. Crop marks are small L-shaped marks at the 4 corners of the final |
| # panel. These practically define the extents of the panel and are required by |
| # some board manufacturers. Crop marks are also required if you want to leave |
| # extra space around the final panel for tooling or handling. Option |
| # 'CropMarkWidth' sets the thickness of these crop marks. |
| # |
| # NOTE: Layer names are ALL LOWERCASE, even if you define them with uppercase |
| # letters below. |
| CropMarkLayers = *topsilkscreen,*bottomsilkscreen |
| |
| # Set this option to the name of a file in which to write a Gerber fabrication |
| # drawing. Some board manufacturers require a fabrication drawing with panel |
| # dimensions and drill hit marks and drill legend. There's no harm in creating |
| # this file...you can ignore it if you don't need it. |
| #FabricationDrawingFile = %(mergeout)s.fab |
| |
| # If FabricationDrawingFile is specified, you can provide an optional file name |
| # of a file containing arbitrary text to add to the fabrication drawing. This |
| # text can indicate manufacturing information, contact information, etc. |
| #FabricationDrawingText = %(projdir)s/fabdwg.txt |
| |
| # Option to generate leading zeros in the output Excellon drill file, i.e., to |
| # NOT use leading-zero suppression. Some Gerber viewers cannot properly guess |
| # the Excellon file format when there are no leading zeros. Set this option to |
| # 1 if your Gerber viewer is putting the drill holes in far off places that do |
| # not line up with component pads. |
| ExcellonLeadingZeros = 0 |
| |
| # Optional additional Gerber layer on which to draw a rectangle defining the |
| # extents of the entire panelized job. This will create a Gerber file (with |
| # name specified by this option) that simply contains a rectangle defining the |
| # outline of the final panel. This outline file is useful for circuit board |
| # milling to indicate a path for the router tool. There's no harm in creating |
| # this file...you can ignore it if you don't need it. |
| OutlineLayerFile = %(mergeout)s-Outline.gbr |
| |
| # Optional additional Gerber layer on which to draw horizontal and vertical |
| # lines describing where to score (i.e., V-groove) the panel so that jobs |
| # can easily snap apart. These scoring lines will be drawn half-way between |
| # job borders. |
| ScoringFile = %(mergeout)s-Score.gbr |
| |
| # Set the maximum dimensions of the final panel, if known. You can set the |
| # dimensions of the maximum panel size supported by your board manufacturer, |
| # and GerbMerge will print an error message if your layout exceeds these |
| # dimensions. Alternatively, when using automatic placement, the panel sizes |
| # listed here constrain the random placements such that only placements that |
| # fit within the given panel dimensions will be considered. The dimensions are |
| # specified in inches. |
| PanelWidth = 150 |
| PanelHeight = 150 |
| |
| # Set the amount of extra space to leave around the edges of the panel to |
| # simplify tooling and handling. These margins are specified in inches, and |
| # default to 0" if not specified. These spacings will only be visible to the |
| # board manufacturer if you enable crop marks (see CropMarkLayers above) or use |
| # an OutlineLayer. |
| LeftMargin = 0 |
| RightMargin = 0 |
| TopMargin = 0 |
| BottomMargin = 0 |
| |
| ################################################################ |
| # |
| # Settings that are probably not important |
| # |
| ################################################################ |
| |
| # Set the inter-job spacing (inches) in both the X-dimension (width) and |
| # Y-dimension (height). Normally these would be the same unless you're trying |
| # really hard to make your jobs fit into a panel of exact size and you need to |
| # tweak these spacings to make it work. 0.125" is probably generous, about half |
| # that is practical for using a band saw, but you probably want to leave it at |
| # 0.125" if you have copper features close to the board edges and/or are using |
| # less precise tools, like a hacksaw, for separating the boards. |
| XSpacing = 2.54 |
| YSpacing = 2.54 |
| |
| # Width of cut lines, in inches. The default value is 0.01". These are drawn on |
| # the layers specified by CutLineLayers. |
| CutLineWidth = 0.01 |
| |
| # Width of crop marks, in inches. The default value is 0.01". These are drawn on |
| # the layers specified by CropMarkLayers. |
| CropMarkWidth = 0.01 |
| |
| # This option is intended to reduce the probability of forgetting to include a |
| # layer in a job description when panelizing two or more different jobs. |
| # Unless this option is set to 1, an error will be raised if some jobs do not |
| # have the same layer names as the others, i.e., are missing layers. For |
| # example, if one job has a top-side soldermask layer and another doesn't, that |
| # could be a mistake. Setting this option to 1 prevents this situation from |
| # raising an error. |
| AllowMissingLayers = 0 |
| |
| # This option is intended to reduce the number of drills in the output by |
| # eliminating drill sizes that are too close to make a difference. For example, |
| # it probably does not make sense to have two separate 0.031" and 0.0315" |
| # drills. The DrillClusterTolerance value specifies how much tolerance is |
| # allowed in drill sizes, in units of inches. Multiple drill tools that span |
| # twice this tolerance will be clustered into a single drill tool. For example, |
| # a set of 0.031", 0.0315", 0.032", and 0.034" drills will all be replaced by a |
| # single drill tool of diameter (0.031"+0.034")/2 = 0.0325". It is guaranteed |
| # that all original drill sizes will be no farther than DrillClusterTolerance |
| # from the drill tool size generated by clustering. |
| # |
| # Setting DrillClusterTolerance to 0 disables clustering. |
| DrillClusterTolerance = 0.002 |
| |
| # Use this option to automatically thicken features on particular layers. This |
| # is intended for thickening silkscreen to some minimum width. The value of |
| # this option must be a comma-separated list of layer names followed by minimum |
| # feature sizes (in inches) for that layer. Comment this out to disable thickening. |
| MinimumFeatureSize = *topsilkscreen,0.008,*bottomsilkscreen,0.008 |
| |
| ############################################################################## |
| # This section sets the name of merged output files. Each assignment below |
| # specifies a layer name and the file name that is to be written for that |
| # merged layer. Except for the BoardOutline and Drills layer names, all other |
| # layer names must begin with an asterisk '*'. The special layer name Placement |
| # is used to specify the placement file that can be used with the |
| # '--place-file' command-line option in a future invocation of GerbMerge. The |
| # special layer name ToolList is used to specify the file name that represents |
| # the tool list for the panelized job. |
| # |
| # By default, if this section is omitted or no layername=filename assignment is |
| # made, the following files are generated: |
| # |
| # BoardOutline = merged.boardoutline.ger |
| # Drills = merged.drills.xln |
| # Placement = merged.placement.xml |
| # ToolList = merged.toollist.drl |
| # *layername = merged.layername.ger |
| # (for example: 'merged.toplayer.ger', 'merged.silkscreen.ger') |
| # |
| # Any assignment that does not begin with '*' or is not one of the reserved |
| # names BoardOutline, Drills, ToolList, or Placement is a generic string |
| # assignment that can be used for string substitutions, to save typing. |
| ############################################################################## |
| [MergeOutputFiles] |
| Prefix = %(mergeout)s |
| |
| # KHK my interpretation for KiCAD on a Linux system (case sensitive) |
| *TopLayer=%(prefix)s-F.Cu.gbr |
| *BottomLayer=%(prefix)s-B.Cu.gbr |
| *TopSilkscreen=%(prefix)s-F.SilkS.gbr |
| *TopSoldermask=%(prefix)s-F.Mask.gbr |
| *BottomSilkscreen=%(prefix)s-B.SilkS.gbr |
| *BottomSoldermask=%(prefix)s-B.Mask.gbr |
| *NPTHDrills=%(prefix)s-NPTH.drl |
| Drills=%(prefix)s.drl |
| BoardOutline=%(prefix)s-Edge.Cuts.gbr |
| ToolList = toollist.%(prefix)s.drl |
| Placement = placement.%(prefix)s.txt |
| |
| ############################################################################## |
| # The remainder of the file specifies the jobs to be panelized. Each job is |
| # specified in its own section. To each job you can assign a job name, which |
| # will be the name of the section in square brackets (e.g., [Proj1]). This job |
| # name is used in the layout file (if used) to refer to the job. |
| # |
| # Job names are case-sensitive, but do not create job names that are the same |
| # except for the case of the characters, as this may cause problems during |
| # layout. Job names may only contain the following characters: |
| # |
| # a-z A-Z 0-9 _ |
| # |
| # In addition, job names must begin with a letter (a-z or A-Z). |
| ############################################################################## |
| [HBSTEP02A] |
| |
| Prefix=%(projdir)s/HBSTEP02A/HBSTEP02A |
| |
| *TopLayer=%(prefix)s-F.Cu.gbr |
| *BottomLayer=%(prefix)s-B.Cu.gbr |
| *TopSilkscreen=%(prefix)s-F.SilkS.gbr |
| *TopSoldermask=%(prefix)s-F.Mask.gbr |
| *BottomSoldermask=%(prefix)s-B.Mask.gbr |
| Drills=%(prefix)s.drl |
| BoardOutline=%(prefix)s-Edge.Cuts.gbr |
| Repeat = 4 |
| |
| |
| |