| 2,11 → 2,13 |
|---|
| include <../configuration.scad> |
| include <polyScrewThread_r1.scad> |
| |
| |
| difference () { |
| AWSCREEN01A_D03(D03_vyska_zavitu,D03_tolerance_zavitu,D03_material_za_zavitem,D03_polomer_zavitu,D03_polomer_stitu,D03_tloustka_materialu,D03_vyska_stitu,D03_pocet_vyztuh,screen_bevel); |
| |
| |
| cube([180,180,180]); |
| |
| } |
| |
| |
| |
| 16,15 → 18,35 |
|---|
| { |
| angle_sep = 360/D03_pocet_vyztuh; |
| |
| //spodní kruh |
| //spodní kruh - kvůli výkroji |
| difference () { |
| |
| |
| cylinder (h=3*D03_tloustka_materialu,r = D03_polomer_stitu,$fn=100); |
| translate ([0,0,-0.005]) |
| cylinder (h=2*D03_tloustka_materialu+0.01,r = D03_polomer_stitu-D03_tloustka_materialu,$fn=100); |
| |
| translate ([0,0,3*D03_tloustka_materialu]) |
| |
| translate ([0,0,-0.01/2-D03_tloustka_materialu]) |
| cylinder (h=D03_vyska_stitu-3*D03_tloustka_materialu+0.01,r1=D03_polomer_stitu ,r2=D03_polomer_zavitu -D03_tolerance_zavitu- D03_material_za_zavitem,$fn=100); |
| |
| |
| |
| |
| } |
| |
| //spodní kruh - kvůli doplnění výkroje |
| difference () { |
| |
| |
| cylinder (h=3*D03_tloustka_materialu,r = D03_polomer_stitu,$fn=100); |
| translate ([0,0,-0.005]) |
| cylinder (h=3*D03_tloustka_materialu+0.01,r = D03_polomer_stitu-D03_tloustka_materialu,$fn=100); |
| |
| } |
| |
| |
| } |
| |
| |
| //horni zavit |
| 42,15 → 64,30 |
|---|
| |
| } |
| |
| //materiál pod horním závitem |
| translate ([0,0,D03_vyska_stitu-D03_tloustka_materialu]) |
| difference () { |
| translate ([0,0,0]) |
| cylinder (h=D03_tloustka_materialu ,r=D03_polomer_zavitu -D03_tolerance_zavitu- D03_material_za_zavitem+D03_tloustka_materialu ,$fn=100); |
| |
| |
| translate ([0,0,-0.01]) |
| cylinder (h=D03_tloustka_materialu+0.02 ,r= D03_polomer_zavitu -D03_tolerance_zavitu- D03_material_za_zavitem ,$fn=100); |
| |
| } |
| |
| |
| |
| //screen |
| |
| translate ([0,0,3*D03_tloustka_materialu]) |
| difference () { |
| cylinder (h=D03_vyska_stitu-3*D03_tloustka_materialu,r1=D03_polomer_stitu ,r2=D03_polomer_zavitu-D03_tolerance_zavitu,$fn=100); |
| translate ([0,0,-0.01/2]) |
| cylinder (h=D03_vyska_stitu-3*D03_tloustka_materialu+0.01,r1=D03_polomer_stitu-D03_tloustka_materialu ,r2=D03_polomer_zavitu- D03_material_za_zavitem-D03_tolerance_zavitu,$fn=100); |
| cylinder (h=D03_vyska_stitu-3*D03_tloustka_materialu,r1=D03_polomer_stitu ,r2=D03_polomer_zavitu -D03_tolerance_zavitu- D03_material_za_zavitem,$fn=100); |
| translate ([0,0,-0.01/2-D03_tloustka_materialu]) |
| cylinder (h=D03_vyska_stitu-3*D03_tloustka_materialu+0.01,r1=D03_polomer_stitu ,r2=D03_polomer_zavitu -D03_tolerance_zavitu- D03_material_za_zavitem,$fn=100); |
| |
| translate ([0,0,D03_vyska_stitu-D03_vyska_zavitu-3*D03_tloustka_materialu]) |
| cylinder (h=D03_vyska_zavitu+0.02 ,r= D03_polomer_zavitu -D03_tolerance_zavitu- D03_material_za_zavitem ,$fn=100); |
| |
| |
| } |