| 0,0 → 1,66 |
|---|
| $fn=40; // model faces resolution. |
| include <../configuration.scad> |
| |
| include <AWSCREEN01A_D06.scad> |
| include <polyScrewThread_r1.scad> |
| |
| PI=3.141592; |
| |
| |
| |
| module AWSCREEN01A_D05(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu) |
| { |
| |
| difference() |
| { |
| |
| union() |
| { |
| //zavit |
| translate([0,0,D01_material_pod_zavitem]) |
| screw_thread(S01_prumer_zavitu-0.5,4,55,S01_vyska_komponentu_na_lozisko,PI/2,2); |
| |
| //spodní valec |
| translate([0,0,D01_material_pod_zavitem/2]) |
| cylinder (h = D01_material_pod_zavitem, r=(S01_prumer_zavitu+D01_material_pred_zavitem*2)/2, center = true, $fn=100); |
| |
| //uchyt na tyc |
| translate([0,D01_delka_tyce/2+S01_prumer_zavitu/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) |
| cube([D01_sirka_tyce,D01_delka_tyce,D01_material_pod_zavitem],center=true); |
| //uchyt na tyc ovalna cast |
| translate([0,S01_prumer_zavitu/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) |
| cube([D01_sirka_tyce,D01_material_za_zavitem+D01_material_pred_zavitem,D01_material_pod_zavitem],center=true); |
| |
| |
| //material kolem uchytu na sloupek |
| translate([0,D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+(D02_sila_materialu+D02_prumer_obruby/2)/2-D02_dotahova_vzdalenost,D01_material_pod_zavitem/2]) |
| difference() |
| { |
| cube([D01_sirka_tyce,D02_sila_materialu+D02_prumer_obruby/2,D01_material_pod_zavitem],center=true); |
| translate([0,D02_prumer_obruby/2-D02_dotahova_vzdalenost-D02_sila_materialu,0]) |
| cylinder(h=D02_vyska_uchytky+0.01,r=D02_prumer_obruby/2,center=true); |
| |
| } |
| |
| |
| |
| //uchyt na sloupek |
| |
| translate([0,D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+D02_sila_materialu+(D02_prumer_obruby)/2,D02_vyska_uchytky/2]) |
| rotate(a=[0,0,270]) |
| AWSCREEN01A_D06(D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu); |
| |
| } |
| |
| //otvor |
| translate([0,0,(D01_material_pod_zavitem+S01_vyska_komponentu_na_lozisko)/2]) |
| cylinder (h = D01_material_pod_zavitem+S01_vyska_komponentu_na_lozisko+0.02, r=(S01_prumer_zavitu-2*D01_material_za_zavitem)/2, center = true, $fn=100); |
| |
| } |
| } |
| |
| AWSCREEN01A_D05(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu); |
| |
| |
| |
| |