| 8,7 → 8,7 |
|---|
| |
| |
| |
| module AWSCREEN01A_D05(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu) |
| module AWSCREEN01A_D05(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu,D03_tolerance_zavitu) |
| { |
| |
| difference() |
| 15,15 → 15,31 |
|---|
| { |
| |
| union() |
| { |
| { |
| //výstuha |
| //translate ([0,0,-D03_tloustka_materialu/2]) |
| rotate ([0,-90,0]) |
| linear_extrude (height = D03_tloustka_materialu, convexity = 10) |
| polygon(points=[[D02_vyska_uchytky/2,D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+D02_sila_materialu],[0, D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+D02_sila_materialu],[0,D03_polomer_stitu+D01_material_pred_zavitem],[D01_material_pod_zavitem,D03_polomer_stitu+D01_material_pred_zavitem]]); |
| |
| |
| //zavit |
| translate([0,0,D01_material_pod_zavitem]) |
| screw_thread(S01_prumer_zavitu-0.5,4,55,S01_vyska_komponentu_na_lozisko,PI/2,2); |
| screw_thread(S01_prumer_zavitu-2*D03_tolerance_zavitu,4,55,S01_vyska_komponentu_na_lozisko,PI/2,2); |
| |
| |
| difference() |
| { |
| //spodní valec |
| translate([0,0,D01_material_pod_zavitem/2]) |
| cylinder (h = D01_material_pod_zavitem, r=(S01_prumer_zavitu+D01_material_pred_zavitem*2)/2, center = true, $fn=100); |
| |
| translate([0,0,-4]) |
| screw_thread(S01_prumer_zavitu-D01_material_za_zavitem,4,55,D01_material_pod_zavitem+8,PI/2,2); |
| |
| |
| } |
| |
| //uchyt na tyc |
| translate([0,D01_delka_tyce/2+S01_prumer_zavitu/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) |
| cube([D01_sirka_tyce,D01_delka_tyce,D01_material_pod_zavitem],center=true); |
| 53,13 → 69,15 |
|---|
| } |
| |
| //otvor |
| translate([0,0,(D01_material_pod_zavitem+S01_vyska_komponentu_na_lozisko)/2]) |
| cylinder (h = D01_material_pod_zavitem+S01_vyska_komponentu_na_lozisko+0.02, r=(S01_prumer_zavitu-2*D01_material_za_zavitem)/2, center = true, $fn=100); |
| translate([0,0,D01_material_pod_zavitem+S01_vyska_komponentu_na_lozisko/2]) |
| cylinder (h = S01_vyska_komponentu_na_lozisko+0.02, r=(S01_prumer_zavitu-2*D03_tolerance_zavitu-D01_material_za_zavitem)/2, center = true, $fn=100); |
| |
| |
| |
| } |
| } |
| |
| AWSCREEN01A_D05(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu); |
| AWSCREEN01A_D05(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu,D03_tolerance_zavitu); |
| |
| |
| |