| /Modules/Mechanical/Boxes/BASEBOX02A/CAD/print_data/BASEBOX01A_plate3.scad |
|---|
| File deleted |
| /Modules/Mechanical/Boxes/BASEBOX02A/CAD/print_data/BASEBOX01A_plate4.scad |
|---|
| File deleted |
| \ No newline at end of file |
| /Modules/Mechanical/Boxes/BASEBOX02A/CAD/print_data/BASEBOX01A_PLBASE_top.scad |
|---|
| File deleted |
| \ No newline at end of file |
| /Modules/Mechanical/Boxes/BASEBOX02A/CAD/print_data/BASEBOX01A_upright.scad |
|---|
| File deleted |
| /Modules/Mechanical/Boxes/BASEBOX02A/CAD/print_data/BASEBOX01A_PLBASE_bottom.scad |
|---|
| File deleted |
| /Modules/Mechanical/Boxes/BASEBOX02A/CAD/print_data/BASEBOX01A_plate1.scad |
|---|
| File deleted |
| \ No newline at end of file |
| /Modules/Mechanical/Boxes/BASEBOX02A/CAD/print_data/BASEBOX01A_plate2.scad |
|---|
| File deleted |
| \ No newline at end of file |
| /Modules/Mechanical/Boxes/BASEBOX02A/CAD/print_data/BASEBOX02A.scad |
|---|
| 0,0 → 1,24 |
| use <../configuration/plbase.scad> |
| use <../configuration/sloupek.scad> |
| use <../configuration/bocnice.scad> |
| include <../configuration/manufactury_conf.scad> |
| include <../configuration.scad> |
| //BOCNICE |
| //------------------------------------------------------------- |
| translate([0,0,(vyska_bocnice/2)+tloustka_plbase]) |
| bocnice(pocet_der1+2,pocet_der2+2,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice); |
| //PLBASE SPODNI |
| //------------------------------------------------------------- |
| translate([-((pocet_der2+2)*vzdalenost_der+2*vzdalenost_od_okraje)/2-tloustka_bocnice,-vzdalenost_od_okraje-tloustka_bocnice,tloustka_plbase]) |
| rotate(a=[180,0,90]) |
| plbase(pocet_der1+3,pocet_der2+3,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,tloustka_plbase,prekryti_der,tloustka_bocnice); |
| /Modules/Mechanical/Boxes/BASEBOX02A/CAD/print_data/BASEBOX02A_PLBASE_top.scad |
|---|
| 0,0 → 1,15 |
| use <../configuration/plbase.scad> |
| include <../configuration/manufactury_conf.scad> |
| include <../configuration.scad> |
| translate([-((pocet_der2+2)*vzdalenost_der+2*vzdalenost_od_okraje)/2-tloustka_bocnice,-((pocet_der1+2)*vzdalenost_der+2*vzdalenost_od_okraje)/2-tloustka_bocnice,0]) |
| rotate(a=[0,0,0]) |
| { |
| plbase_bez_der_napis(pocet_der2+3,pocet_der1+3,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,tloustka_plbase,prekryti_der,box_jmeno,tloustka_bocnice); |
| } |