| 0,0 → 1,135 |
|---|
| use <text/Write.scad> |
| use <MLAB_logo.scad> |
| use <sloupek.scad> |
| use <plbase.scad> |
| include <manufactury_conf.scad> |
| include <../configuration.scad> |
| |
| bocnice(pocet_der1,pocet_der2,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice); |
| |
| //Bočnice |
| //------------------------------------------------------------ |
| |
| |
| module bocnice(pocet_der1,pocet_der2,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice){ |
| |
| difference () { |
| union() |
| { |
| translate([-((pocet_der2)*vzdalenost_der+2*vzdalenost_od_okraje)/2,-vzdalenost_od_okraje,vyska_bocnice/2]) |
| rotate(a=[180,0,90]) |
| translate([radidus_hrany,radidus_hrany,0]) |
| translate([-tloustka_bocnice,-tloustka_bocnice,0]) |
| |
| //obvod |
| difference () { |
| |
| minkowski() |
| { |
| cube([(pocet_der1)*vzdalenost_der+2*vzdalenost_od_okraje-2*radidus_hrany+2*tloustka_bocnice,(pocet_der2)*vzdalenost_der+2*vzdalenost_od_okraje-2*radidus_hrany+2*tloustka_bocnice,vyska_bocnice+tloustka_plbase]); // base plastics brick |
| cylinder(r=radidus_hrany,h=0.01); |
| } |
| |
| translate([tloustka_bocnice-radidus_hrany,tloustka_bocnice-radidus_hrany,-0.1]) |
| |
| cube([(pocet_der1)*vzdalenost_der+2*vzdalenost_od_okraje,(pocet_der2)*vzdalenost_der+2*vzdalenost_od_okraje,vyska_bocnice+tloustka_plbase+0.2]); |
| |
| |
| |
| } |
| |
| |
| |
| //SLOUPKY |
| //------------------------------------------------------------ |
| //sloupek 1 |
| |
| translate([(-(pocet_der2)*vzdalenost_der)/2-vzdalenost_od_okraje+prumer_matice/2,-vzdalenost_od_okraje+prumer_matice/2,vyska_bocnice/2-(vyska_matice+2*tloustka_bocnice+0.1)-tloustka_plbase]) |
| sloupek (); |
| |
| //sloupek 2 |
| |
| translate([((pocet_der2)*vzdalenost_der)/2+vzdalenost_od_okraje-prumer_matice/2,-vzdalenost_od_okraje+prumer_matice/2,vyska_bocnice/2-(vyska_matice+2*tloustka_bocnice+0.1)-tloustka_plbase]) |
| rotate(a=[0,0,90]) |
| sloupek (); |
| |
| //sloupek 3 |
| |
| translate([((pocet_der2)*vzdalenost_der)/2+vzdalenost_od_okraje-prumer_matice/2, (pocet_der1)*vzdalenost_der+vzdalenost_od_okraje-prumer_matice/2,vyska_bocnice/2-(vyska_matice+2*tloustka_bocnice+0.1)-tloustka_plbase]) |
| rotate(a=[0,0,180]) |
| sloupek (); |
| |
| //sloupek 4 |
| |
| translate([-((pocet_der2)*vzdalenost_der)/2-vzdalenost_od_okraje+prumer_matice/2, (pocet_der1)*vzdalenost_der+vzdalenost_od_okraje-prumer_matice/2,vyska_bocnice/2-(vyska_matice+2*tloustka_bocnice+0.1)-tloustka_plbase]) |
| rotate(a=[0,0,270]) |
| sloupek (); |
| |
| //uchyt 1 |
| translate([(-(pocet_der2)*vzdalenost_der)/2-vzdalenost_od_okraje-Uchyt_radius/2-Uchyt_x+0.5,-vzdalenost_od_okraje+vzdalenost_der/2,-vyska_bocnice/2-tloustka_plbase]) |
| uchyt(); |
| |
| //uchyt 2 |
| translate([((pocet_der2)*vzdalenost_der)/2+vzdalenost_od_okraje+tloustka_bocnice+Uchyt_radius-0.5,-vzdalenost_od_okraje+vzdalenost_der/2,-vyska_bocnice/2-tloustka_plbase]) |
| uchyt(); |
| |
| //uchyt 3 |
| translate([(-(pocet_der2)*vzdalenost_der)/2-vzdalenost_od_okraje-Uchyt_radius/2-Uchyt_x+0.5,(pocet_der1)*vzdalenost_der+vzdalenost_od_okraje-Uchyt_y+Uchyt_radius-vzdalenost_der/2,-vyska_bocnice/2-tloustka_plbase]) |
| uchyt(); |
| |
| //uchyt 4 |
| translate([((pocet_der2)*vzdalenost_der)/2+vzdalenost_od_okraje+tloustka_bocnice+Uchyt_radius-0.5,(pocet_der1)*vzdalenost_der+vzdalenost_od_okraje-Uchyt_y+Uchyt_radius-vzdalenost_der/2,-vyska_bocnice/2-tloustka_plbase]) |
| uchyt(); |
| |
| } |
| |
| //---------------------------------------------------- |
| //LOGO MLAB |
| /* |
| translate([(5-(pocet_der2)*vzdalenost_der)/2,0,0]) |
| translate ([0, -vzdalenost_od_okraje-tloustka_bocnice*1/2,0]) // |
| rotate([0, 90, 270]) |
| scale(v = [logo_sirka, logo_vyska, 0.3]) |
| MLAB_logo_short(); |
| */ |
| |
| |
| |
| //plbase odecet na kryt |
| translate([0,0,vyska_bocnice/2-tloustka_plbase/2+0.05]) |
| rotate(a=[0,0,0]) |
| { |
| plbase_vrchni_kryt_pro_odecet(pocet_der1,pocet_der2,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice,0,tloustka_plbase+0.1); |
| } |
| |
| |
| } |
| } |
| |
| |
| |
| |
| //uchyt(); |
| |
| module uchyt(){ |
| difference () { |
| minkowski() |
| { |
| cube([Uchyt_x-2*Uchyt_radius,Uchyt_y-2*Uchyt_radius,Uchyt_vyska_mat+M3_vyska_hlavy]); // base plastics brick |
| cylinder(r=Uchyt_radius,h=0.1); |
| } |
| |
| //otvor na hlavu |
| translate([(Uchyt_x)/2-Uchyt_radius,(Uchyt_y)/2-Uchyt_radius,Uchyt_vyska_mat+M3_vyska_hlavy/2]) |
| cylinder(h=M3_vyska_hlavy+0.6, r=M3_prumer_hlavy/2, center=true); |
| |
| ////otvor na sroub |
| translate([(Uchyt_x)/2-Uchyt_radius,(Uchyt_y)/2-Uchyt_radius,(Uchyt_vyska_mat+M3_vyska_hlavy)/2]) |
| cylinder(h=Uchyt_vyska_mat+M3_vyska_hlavy+0.6, r=M3_prumer/2, center=true); |
| |
| |
| } |
| } |
| |
| |
| |