| 0,0 → 1,63 |
|---|
| $fn=40; // model faces resolution. |
| include <../configuration2.scad> |
| |
| include <ISLHOLDER01A_D04.scad> |
| |
| |
| PI=3.141592; |
| |
| //Držák anemometru |
| |
| module ISLHOLDER01A_D03() |
| { |
| difference() |
| { |
| union() |
| { |
| //výstuha |
| translate([S01_sila_materialu/2,0,0]) |
| rotate ([0,-90,0]) |
| linear_extrude (height = S01_sila_materialu, convexity = 10) |
| polygon(points=[[D02_vyska_uchytky/2,D01_delka_tyce+S01_prumer_vnitrni/2+D01_material_pred_zavitem+D02_sila_materialu-1],[0, D01_delka_tyce+S01_prumer_vnitrni/2+D01_material_pred_zavitem+D02_sila_materialu-1],[0,S01_prumer_vnitrni/2+D01_material_pred_zavitem],[D02_vyska_uchytky/3,S01_prumer_vnitrni/2+D01_material_pred_zavitem]]); |
| |
| rotate ([90,0,0]) |
| translate([0,15,D01_material_pod_zavitem/2-S01_prumer_vnitrni/2-D01_material_pred_zavitem]) |
| difference() { |
| cube([D01_sirka_tyce,30,D01_material_pod_zavitem],center=true); |
| translate([0,8,0]) |
| cylinder(h=D01_material_pod_zavitem+0.01,r=D02_prumer_uchytneho_sroubu/2,center=true); |
| } |
| |
| //uchyt na tyc |
| translate([0,D01_delka_tyce/2+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) |
| cube([D01_sirka_tyce,D01_delka_tyce,D01_material_pod_zavitem],center=true); |
| |
| //uchyt na tyc ovalna cast |
| translate([0,(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) |
| cube([D01_sirka_tyce,D01_material_za_zavitem+D01_material_pred_zavitem,D01_material_pod_zavitem],center=true); |
| |
| //material kolem uchytu na sloupek |
| translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+(D02_sila_materialu+D02_prumer_obruby/2)/2-D02_dotahova_vzdalenost,D01_material_pod_zavitem/2]) |
| |
| difference() |
| { |
| cube([D01_sirka_tyce,D02_sila_materialu+D02_prumer_obruby/2,D01_material_pod_zavitem],center=true); |
| |
| translate([0,D02_prumer_obruby/2-D02_dotahova_vzdalenost-D02_sila_materialu,0]) |
| cylinder(h=D02_vyska_uchytky+0.01,r=D02_prumer_obruby/2,center=true); |
| } |
| |
| //uchyt na sloupek |
| translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+D02_sila_materialu+(D02_prumer_obruby)/2,D02_vyska_uchytky/2]) |
| rotate(a=[0,0,270]) |
| ISLHOLDER01A_D04_2(); |
| |
| } |
| |
| |
| |
| } |
| } |
| |
| ISLHOLDER01A_D03(); |
| |