| 0,0 → 1,47 |
|---|
| $fn = 100; |
| |
| |
| module LCD_frontPanel(){ |
| WIDTH = 7; // pocet der na zakl desku. Min je 8 |
| FOOT_X_SHIFT = 0; // posun v ose X, tzn. vysunutí ven, nebo dovnitř. 0 je v rovine s kratsi hranou zakl. desky ASBASE1115 |
| DISPLAY_Z_SHIFT = 2; // mezera, která vznikne mezi "nohou" a spodní hranou PCB |
| FOOT_THICK = 7; // síla spodní "nohy" (toho, v cem jsou srouby) |
| BHEAD_HEIGHT = 2.5; // vyska hlavicky sroubu |
| BHEAD_DIAMETER = 6; // vyska hlavicky sroubu |
| BOLT_DIAMETER = 3.2; // vyska hlavicky sroubu |
| NUT_HEIGHT = 2.1; // vyska matky |
| NUT_DIAMETER = 6; // vyska matky |
| CLEAR = 0.1; |
| |
| difference(){ |
| union(){ |
| translate([0, 4 +FOOT_X_SHIFT, 0+DISPLAY_Z_SHIFT/2])cube([80,8,36+DISPLAY_Z_SHIFT], center=true); |
| translate([0, 4 +FOOT_X_SHIFT/2, (-36-FOOT_THICK)/2])cube([80,8+FOOT_X_SHIFT,FOOT_THICK], center=true); |
| translate([+75/2, 0, +31/2+DISPLAY_Z_SHIFT]) rotate([90,0,0]) cylinder(FOOT_THICK, 2.3/2, 2.3/2); |
| translate([+75/2, 0, -31/2+DISPLAY_Z_SHIFT]) rotate([90,0,0]) cylinder(FOOT_THICK, 2.3/2, 2.3/2); |
| translate([-75/2, 0, +31/2+DISPLAY_Z_SHIFT]) rotate([90,0,0]) cylinder(FOOT_THICK, 2.3/2, 2.3/2); |
| translate([-75/2, 0, -31/2+DISPLAY_Z_SHIFT]) rotate([90,0,0]) cylinder(FOOT_THICK, 2.3/2, 2.3/2); |
| hull(){ |
| translate([-40+10.16/2, -0.8, (-36)/2-FOOT_THICK]) cylinder(FOOT_THICK, 10.16/2, 10.16/2); |
| translate([+40-10.16/2, -0.8, (-36)/2-FOOT_THICK]) cylinder(FOOT_THICK, 10.16/2, 10.16/2); |
| } |
| /*#hull(){ |
| translate([-5.08 + (-WIDTH/2+1)*10.16, -0.8, (-36)/2-FOOT_THICK]) cylinder(FOOT_THICK, 10.16/2, 10.16/2); |
| translate([-5.08 + (-WIDTH/2+5)*10.16, -0.8, (-36)/2-FOOT_THICK]) cylinder(FOOT_THICK, 10.16/2, 10.16/2); |
| }*/ |
| } |
| union(){ |
| translate([0, 4 + FOOT_X_SHIFT, +DISPLAY_Z_SHIFT]) cube([72,8,25.3], center=true); |
| translate([-5, FOOT_X_SHIFT, 36/2-4+DISPLAY_Z_SHIFT]) cube([41,4,4]); |
| for (x=[1:WIDTH]){ |
| translate([-5.08 + (-WIDTH/2+x)*10.16, -0.8, (-36)/2-FOOT_THICK]) cylinder(12, BOLT_DIAMETER/2, BOLT_DIAMETER/2); |
| translate([-5.08 + (-WIDTH/2+x)*10.16, -0.8, (-36)/2-BHEAD_HEIGHT]) cylinder(3+10, BHEAD_DIAMETER/2, BHEAD_DIAMETER/2); |
| translate([-5.08 + (-WIDTH/2+x)*10.16, -0.8, (-36)/2-FOOT_THICK]) cylinder(NUT_HEIGHT, NUT_DIAMETER/2, NUT_DIAMETER/2, $fn=6); |
| |
| } |
| } |
| } |
| } |
| |
| |
| LCD_frontPanel(); |