WebSVN – MLAB – /Modules/Mechanical/WINDGAUGE01A/ Rev 4278 and /Modules/Mechanical/WINDGAUGE01A/ Rev 4279 – Path Comparison

 /Modules/Mechanical/WINDGAUGE01A/CAD/assembly.scad
 ,6 → 4,9
 use <configuration/stator1.scad>
 use <configuration/stator2.scad>
 use <configuration/stator3.scad>
+use <configuration/stator4.scad>
+use <configuration/lopatky.scad>
+use <configuration/kryt_rotoru.scad>
 include <configuration.scad>
 ,12 → 17,17
 barva_rotor3 = "green";
 barva_rotor4 = "yellow";
-posunuti_dilu=10; //posunuti dilu od sebe
+posunuti_dilu=0; //posunuti dilu od sebe
+translate([0,0,posunuti_dilu*4+(vyska_rotoru1-hloubka_prekryti)/2+vyska_uchytu+tolerance_uchytu+vyska_rotoru2])
+kryt_rotoru(prumer_rotoru1,sila_materialu,prumer_sroubu);
 color(barva_rotor1)
-translate([0,0,posunuti_dilu+(vyska_rotoru1-hloubka_prekryti)/2+vyska_uchytu+tolerance_uchytu+vyska_rotoru2/2])
+translate([0,0,posunuti_dilu*3+(vyska_rotoru1-hloubka_prekryti)/2+vyska_uchytu+tolerance_uchytu+vyska_rotoru2/2])
 rotor1(prumer_rotoru1,vyska_rotoru1,prumer_sroubu,vyska_matky,prumer_orechu,sila_materialu,sila_materialu_vule,hloubka_prekryti,hloubka_uchytu,sila_uchytu,vyska_uchytu,tolerance_uchytu);
 ,6 → 74,37
 stator3(stator3_vyska,prumer_rotoru1,lozisko_vyska,sila_pod_loziskem,sila_materialu,vule1,stator3_sila_steny,stator3_vyska_prekryti,prumer_hlavy_sroubu,stator3_vzdalenost_od_steny,lozisko_vyska,prumer_sroubu,roztec_sroubu,uchyt_prumer_sroubu);
+//stator4
+translate([0,0,-posunuti_dilu*7-(vyska_rotoru2/2+vyska_matky+vzdalenost_rot_stat+stator1_sila+stator3_vyska+vyska_stator4/2)])
+rotate(a = [180, 0, 0])
+stator4 (roztec_sroubu,uchyt_prumer_sroubu,vyska_stator4,sila_materialu,uchyt_vyska_matky,uchyt_prumer_orechu,kabel_prumer);
+//lopatky
+//lopatka 1
+rotate(a = [0, 0, 90])
+translate([sila_uchytu/2,-prumer_lopatky/2-delka_uchytu_lopatky-hloubka_uchytu-prumer_rotoru1/2+hloubka_uchytu,posunuti_dilu+vyska_rotoru2/2+vyska_uchytu/2])
+lopatka(hloubka_uchytu,sila_uchytu,vyska_uchytu,tolerance_uchytu,prumer_lopatky,sila_materialu_lopatky,delka_uchytu_lopatky,hrana_uchytu_lopatky,prumer_rotoru1,prumer_sroubu);
+//lopatka 2
+rotate(a = [0, 0, 210])
+translate([sila_uchytu/2,-prumer_lopatky/2-delka_uchytu_lopatky-hloubka_uchytu-prumer_rotoru1/2+hloubka_uchytu,posunuti_dilu+vyska_rotoru2/2+vyska_uchytu/2])
+lopatka(hloubka_uchytu,sila_uchytu,vyska_uchytu,tolerance_uchytu,prumer_lopatky,sila_materialu_lopatky,delka_uchytu_lopatky,hrana_uchytu_lopatky,prumer_rotoru1,prumer_sroubu);
+//lopatka 3
+rotate(a = [0, 0, 330])
+translate([sila_uchytu/2,-prumer_lopatky/2-delka_uchytu_lopatky-hloubka_uchytu-prumer_rotoru1/2+hloubka_uchytu,posunuti_dilu+vyska_rotoru2/2+vyska_uchytu/2])
+lopatka(hloubka_uchytu,sila_uchytu,vyska_uchytu,tolerance_uchytu,prumer_lopatky,sila_materialu_lopatky,delka_uchytu_lopatky,hrana_uchytu_lopatky,prumer_rotoru1,prumer_sroubu);
 //SLOUPKY
 //------------------------------------------------------------
 //sloupek 1

 /Modules/Mechanical/WINDGAUGE01A/CAD/configuration/kryt_rotoru.scad
 ,0 → 1,37
+$fn=40; // model faces resolution.
+//include <../configuration.scad>
+module kryt_rotoru(prumer_rotoru1,sila_materialu,prumer_sroubu)
+{
+    //kopule
+    difference()
+        {
+            sphere(d = prumer_rotoru1, $fn=100);
+            sphere(d = prumer_rotoru1-2*sila_materialu, $fn=100);
+            translate([0,0,-prumer_rotoru1/2])
+                cube(size = [prumer_rotoru1, prumer_rotoru1, prumer_rotoru1], center = true);
+             }
+    //dno krytu
+             difference()
+        {
+            //zakladni valec
+            translate([0,0,sila_materialu/2])
+                cylinder (h = sila_materialu, r=prumer_rotoru1/2, center = true, $fn=100);
+            //odstraněni casti valce
+            translate([prumer_rotoru1/2+prumer_sroubu*2,0,sila_materialu/2])
+                cube(size = [prumer_rotoru1, prumer_rotoru1, sila_materialu+1], center = true);
+  //otvor na sroub
+            translate([0,0,sila_materialu/2])
+                cylinder (h = sila_materialu+0.1, r=prumer_sroubu/2, center = true, $fn=100);
+             }
+}

 /Modules/Mechanical/WINDGAUGE01A/CAD/configuration/lopatky.scad
 ,0 → 1,84
+$fn=40; // model faces resolution.
+//include <../configuration.scad>
+module lopatka(hloubka_uchytu,sila_uchytu,vyska_uchytu,tolerance_uchytu,prumer_lopatky,sila_materialu_lopatky,delka_uchytu_lopatky,hrana_uchytu_lopatky,prumer_rotoru1,prumer_sroubu)
+    {
+        union()
+        {
+        //prechod lopatka drzak
+        difference()
+        {
+        translate([-hrana_uchytu_lopatky/2,prumer_lopatky/4,0])
+        cube([hrana_uchytu_lopatky,(prumer_lopatky/2)+5,hrana_uchytu_lopatky],center=true);
+            sphere(d = prumer_lopatky, $fn=100);
+        }
+        difference()
+        {
+      //lopatka
+      sphere(d = prumer_lopatky, $fn=100);
+        sphere(d = prumer_lopatky-2*sila_materialu_lopatky, $fn=100);
+          translate([0,-prumer_lopatky/2,-prumer_lopatky/2])
+            cube(size = prumer_lopatky);
+        }
+       //uchyt_lopatky - tycka
+        translate([-hrana_uchytu_lopatky/2,prumer_lopatky/2+delka_uchytu_lopatky/2,0])
+        cube([hrana_uchytu_lopatky,delka_uchytu_lopatky,hrana_uchytu_lopatky],center=true);
+        //uchyt lopatky cast v rotoru
+        translate([-sila_uchytu/2,prumer_lopatky/2+delka_uchytu_lopatky+hloubka_uchytu/2,0])
+         difference()
+         {
+             cube([sila_uchytu,hloubka_uchytu,vyska_uchytu],center=true);
+             //otvor pro sroub
+           translate([0,0,0])
+           cylinder(h=vyska_uchytu+1, r=prumer_sroubu, center=true, $fn=100);
+         //zaobleni
+        translate([0,+prumer_rotoru1/2-hloubka_uchytu/2,0])
+        difference()
+         {
+       cylinder(h=vyska_uchytu+1, r=prumer_rotoru1/2+2, center=true, $fn=100);
+       cylinder(h=vyska_uchytu+2, r=prumer_rotoru1/2, center=true, $fn=100);
+         }
+         }
+         //vyrovnávací úsek mezi úchytem v rotoru a úchytem loplatky (tyčkou)
+translate([0,prumer_lopatky/2+delka_uchytu_lopatky+5/2,0])
+       difference()
+         {
+             translate([-hrana_uchytu_lopatky/2,0,0])
+             cube([hrana_uchytu_lopatky,10,hrana_uchytu_lopatky],center=true);
+        translate([-sila_uchytu,+prumer_rotoru1/2-5/2,0])
+       cylinder(h=vyska_uchytu+1, r=prumer_rotoru1/2, center=true, $fn=100);
+         }
+                }
+                  }

 /Modules/Mechanical/WINDGAUGE01A/CAD/configuration/stator4.scad
 ,0 → 1,50
+$fn=40; // model faces resolution.
+//include <../configuration.scad>
+//stator4 (roztec_sroubu,uchyt_prumer_sroubu,vyska_stator4,sila_materialu,uchyt_vyska_matky,uchyt_prumer_orechu,kabel_prumer);
+module stator4 (roztec_sroubu,uchyt_prumer_sroubu,vyska_stator4,sila_materialu,uchyt_vyska_matky,uchyt_prumer_orechu,kabel_prumer)
+{
+difference()
+{
+    //translate([90,0,0])
+    cube(size = [roztec_sroubu+uchyt_prumer_orechu+2*sila_materialu,roztec_sroubu+uchyt_prumer_orechu+2*sila_materialu, vyska_stator4], center = true);
+//díry pro uchycení anemometru
+     translate([roztec_sroubu/2,roztec_sroubu/2,0])
+ cylinder (h = vyska_stator4+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100);
+      translate([-roztec_sroubu/2,roztec_sroubu/2,0])
+ cylinder (h = vyska_stator4+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100);
+    translate([roztec_sroubu/2,-roztec_sroubu/2,0])
+ cylinder (h = vyska_stator4+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100);
+     translate([-roztec_sroubu/2,-roztec_sroubu/2,0])
+ cylinder (h = vyska_stator4+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100);
+    //dira na kabel
+ cylinder (h = vyska_stator4+0.1, r=(kabel_prumer/2+0.1), center = true, $fn=100);
+    //díry pro matky
+    translate([roztec_sroubu/2,roztec_sroubu/2,vyska_stator4/2-uchyt_vyska_matky/2])
+ cylinder (h = uchyt_vyska_matky+0.1, r=uchyt_prumer_orechu/2, center = true, $fn=100);
+      translate([-roztec_sroubu/2,roztec_sroubu/2,vyska_stator4/2-uchyt_vyska_matky/2])
+ cylinder (h = uchyt_vyska_matky+0.1, r=uchyt_prumer_orechu/2, center = true, $fn=100);
+    translate([roztec_sroubu/2,-roztec_sroubu/2,vyska_stator4/2-uchyt_vyska_matky/2])
+ cylinder (h = uchyt_vyska_matky+0.1, r=uchyt_prumer_orechu/2, center = true, $fn=100);
+     translate([-roztec_sroubu/2,-roztec_sroubu/2,vyska_stator4/2-uchyt_vyska_matky/2])
+ cylinder (h = uchyt_vyska_matky+0.1, r=uchyt_prumer_orechu/2, center = true, $fn=100);
+ }
+  }

 /Modules/Mechanical/WINDGAUGE01A/CAD/configuration.scad
 ,6 → 53,10
 sila_uchytu=12;
 vyska_uchytu=10;
 tolerance_uchytu=0.1;
+delka_uchytu_lopatky=20;
+hrana_uchytu_lopatky=4;
+prumer_lopatky=40;
+sila_materialu_lopatky=2;
 //parametry uchytu senzoru
 roztec_der=10.16;
 ,4 → 94,12
 //uchyt pro anemometr
 uchyt_prumer_sroubu=3.2;
-roztec_sroubu=10.16;
+roztec_sroubu=20;
+//stator 4
+vyska_stator4=5;
+uchyt_vyska_matky=3;
+uchyt_prumer_orechu=10;
+//parametr kabelu
+kabel_prumer=10;

 /Modules/Mechanical/WINDGAUGE01A/CAD/stator4.scad
 ,0 → 1,50
+$fn=40; // model faces resolution.
+//include <../configuration.scad>
+//stator4 (roztec_sroubu,uchyt_prumer_sroubu,vyska_stator4,sila_materialu,uchyt_vyska_matky,uchyt_prumer_orechu);
+module stator4 (roztec_sroubu,uchyt_prumer_sroubu,vyska_stator4,sila_materialu,uchyt_vyska_matky,uchyt_prumer_orechu,kabel_prumer)
+{
+difference()
+{
+    //translate([90,0,0])
+    cube(size = [roztec_sroubu+uchyt_prumer_orechu+2*sila_materialu,roztec_sroubu+uchyt_prumer_orechu+2*sila_materialu, vyska_stator4], center = true);
+//díry pro uchycení anemometru
+     translate([roztec_sroubu/2,roztec_sroubu/2,0])
+ cylinder (h = vyska_stator4+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100);
+      translate([-roztec_sroubu/2,roztec_sroubu/2,0])
+ cylinder (h = vyska_stator4+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100);
+    translate([roztec_sroubu/2,-roztec_sroubu/2,0])
+ cylinder (h = vyska_stator4+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100);
+     translate([-roztec_sroubu/2,-roztec_sroubu/2,0])
+ cylinder (h = vyska_stator4+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100);
+    //dira na kabel
+ cylinder (h = vyska_stator4+0.1, r=(kabel_prumer/2+0.1), center = true, $fn=100);
+    //díry pro matky
+    translate([roztec_sroubu/2,roztec_sroubu/2,vyska_stator4/2-uchyt_vyska_matky/2])
+ cylinder (h = uchyt_vyska_matky+0.1, r=uchyt_prumer_orechu/2, center = true, $fn=100);
+      translate([-roztec_sroubu/2,roztec_sroubu/2,vyska_stator4/2-uchyt_vyska_matky/2])
+ cylinder (h = uchyt_vyska_matky+0.1, r=uchyt_prumer_orechu/2, center = true, $fn=100);
+    translate([roztec_sroubu/2,-roztec_sroubu/2,vyska_stator4/2-uchyt_vyska_matky/2])
+ cylinder (h = uchyt_vyska_matky+0.1, r=uchyt_prumer_orechu/2, center = true, $fn=100);
+     translate([-roztec_sroubu/2,-roztec_sroubu/2,vyska_stator4/2-uchyt_vyska_matky/2])
+ cylinder (h = uchyt_vyska_matky+0.1, r=uchyt_prumer_orechu/2, center = true, $fn=100);
+ }
+  }

Subversion Repositories – MLAB

/Modules/Mechanical/WINDGAUGE01A/ @ 4278 → /Modules/Mechanical/WINDGAUGE01A/ @ 4279

Compare Path:	Rev
With Path:	Rev