| 1,67 → 1,89 |
|---|
| $fn=40; // model faces resolution. |
| include <../configuration.scad> |
| |
| include <WINDGAUGE01A_D02.scad> |
| include <polyScrewThread_r1.scad> |
| |
| PI=3.141592; |
| //Drzak na sloup - cast bez drzaku anemometru |
| module WINDGAUGE01A_D01(){ |
| |
| difference() |
| { |
| union() |
| { |
| //základní válec |
| cylinder(h=D02_vyska_uchytky,r=(D02_prumer_obruby+2*D02_sila_materialu)/2,center=true); |
| //úchytové plošky |
| translate([D02_dotahova_vzdalenost+D02_sila_materialu/2,0,0]){cube([D02_sila_materialu,D02_delka_celeho_uchytu,D02_vyska_uchytky],center=true);} |
| } |
| |
| //válec na odečet |
| cylinder(h=D02_vyska_uchytky+0.01,r=D02_prumer_obruby/2,center=true); |
| |
| //kvádr na odecet |
| translate([D02_dotahova_vzdalenost-(D02_prumer_obruby+2*D02_sila_materialu)/2,0,0]){cube([D02_prumer_obruby+2*D02_sila_materialu,D02_prumer_obruby+2*D02_sila_materialu,D02_vyska_uchytky+0.01],center=true);} |
| |
| //otvory na sroub |
| translate([D02_dotahova_vzdalenost,(D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu,D02_vyska_uchytky/4]){rotate([0,90,0]){cylinder(h=D02_sila_materialu+0.01,r=D02_prumer_uchytneho_sroubu/2);}} |
| |
| //drzak matky |
| translate([D02_dotahova_vzdalenost+D02_sila_materialu-D02_vyska_matky,(D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu,D02_vyska_uchytky/4]){rotate([0,90,0]){ cylinder (h = D02_vyska_matky+0.01, r= (D02_sirka_matky+0.2)/2, $fn=6);}} |
| |
| |
| |
| translate([D02_dotahova_vzdalenost,(D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu,-D02_vyska_uchytky/4]){rotate([0,90,0]){cylinder(h=D02_sila_materialu+0.01,r=D02_prumer_uchytneho_sroubu/2);}} |
| |
| //drzak matky |
| translate([D02_dotahova_vzdalenost+D02_sila_materialu-D02_vyska_matky,(D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu,-D02_vyska_uchytky/4]){rotate([0,90,0]){ cylinder (h = D02_vyska_matky+0.01, r= (D02_sirka_matky+0.2)/2, $fn=6);}} |
| |
| translate([D02_dotahova_vzdalenost,-((D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu),-D02_vyska_uchytky/4]){rotate([0,90,0]){cylinder(h=D02_sila_materialu+0.01,r=D02_prumer_uchytneho_sroubu/2);}} |
| |
| //drzak matky |
| translate([D02_dotahova_vzdalenost+D02_sila_materialu-D02_vyska_matky,-((D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu),-D02_vyska_uchytky/4]){rotate([0,90,0]){ cylinder (h = D02_vyska_matky+0.01, r= (D02_sirka_matky+0.2)/2, $fn=6);}} |
| |
| //Držák anemometru |
| translate([D02_dotahova_vzdalenost,-((D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu),D02_vyska_uchytky/4]){rotate([0,90,0]){cylinder(h=D02_sila_materialu+0.01,r=D02_prumer_uchytneho_sroubu/2);}} |
| |
| //drzak matky |
| translate([D02_dotahova_vzdalenost+D02_sila_materialu-D02_vyska_matky,-((D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu),D02_vyska_uchytky/4]){rotate([0,90,0]){ cylinder (h = D02_vyska_matky+0.01, r= (D02_sirka_matky+0.2)/2, $fn=6);}} |
| |
| } |
| } |
| |
| module WINDGAUGE01A_D01() |
| { |
| module WINDGAUGE01A_D01_2(){ |
| |
| difference() |
| { |
| union() |
| { |
| //výstuha |
| rotate ([0,-90,0]) |
| linear_extrude (height = S01_sila_materialu, convexity = 10) |
| polygon(points=[[D02_vyska_uchytky/2,D01_delka_tyce+S01_prumer_vnitrni/2+D01_material_pred_zavitem+D02_sila_materialu],[0, D01_delka_tyce+S01_prumer_vnitrni/2+D01_material_pred_zavitem+D02_sila_materialu],[0,S01_prumer_vnitrni+D01_material_pred_zavitem],[D01_material_pod_zavitem,S01_prumer_vnitrni+D01_material_pred_zavitem]]); |
| |
| //zavit |
| translate([0,0,D01_material_pod_zavitem]) |
| screw_thread(S01_prumer_vnitrni-S01_tolerance_zavit,4,55,S01_vyska_spodniho_zavitu,PI/2,2); |
| union() |
| { |
| //základní válec |
| cylinder(h=D02_vyska_uchytky,r=(D02_prumer_obruby+2*D02_sila_materialu)/2,center=true); |
| //úchytové plošky |
| translate([D02_dotahova_vzdalenost+D02_sila_materialu/2,0,0]){cube([D02_sila_materialu,D02_delka_celeho_uchytu,D02_vyska_uchytky],center=true);} |
| } |
| |
| //válec na odečet |
| cylinder(h=D02_vyska_uchytky+0.01,r=D02_prumer_obruby/2,center=true); |
| |
| //kvádr na odecet |
| translate([D02_dotahova_vzdalenost-(D02_prumer_obruby+2*D02_sila_materialu)/2,0,0]){cube([D02_prumer_obruby+2*D02_sila_materialu,D02_prumer_obruby+2*D02_sila_materialu,D02_vyska_uchytky+0.01],center=true);} |
| |
| //otvory na sroub |
| translate([D02_dotahova_vzdalenost,(D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu,D02_vyska_uchytky/4]){rotate([0,90,0]){cylinder(h=D02_sila_materialu+0.01,r=D02_prumer_uchytneho_sroubu/2);}} |
| |
| |
| |
| |
| |
| translate([D02_dotahova_vzdalenost,(D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu,-D02_vyska_uchytky/4]){rotate([0,90,0]){cylinder(h=D02_sila_materialu+0.01,r=D02_prumer_uchytneho_sroubu/2);}} |
| |
| |
| |
| translate([D02_dotahova_vzdalenost,-((D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu),-D02_vyska_uchytky/4]){rotate([0,90,0]){cylinder(h=D02_sila_materialu+0.01,r=D02_prumer_uchytneho_sroubu/2);}} |
| |
| |
| |
| //spodní valec |
| translate([0,0,D01_material_pod_zavitem/2]) |
| cylinder (h = D01_material_pod_zavitem, r=(S01_prumer_vnitrni-S01_tolerance_zavit+D01_material_pred_zavitem*2)/2, center = true, $fn=100); |
| |
| //uchyt na tyc |
| translate([0,D01_delka_tyce/2+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) |
| cube([D01_sirka_tyce,D01_delka_tyce,D01_material_pod_zavitem],center=true); |
| |
| //uchyt na tyc ovalna cast |
| translate([0,(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) |
| cube([D01_sirka_tyce,D01_material_za_zavitem+D01_material_pred_zavitem,D01_material_pod_zavitem],center=true); |
| |
| //material kolem uchytu na sloupek |
| translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+(D02_sila_materialu+D02_prumer_obruby/2)/2-D02_dotahova_vzdalenost,D01_material_pod_zavitem/2]) |
| |
| difference() |
| { |
| cube([D01_sirka_tyce,D02_sila_materialu+D02_prumer_obruby/2,D01_material_pod_zavitem],center=true); |
| |
| translate([0,D02_prumer_obruby/2-D02_dotahova_vzdalenost-D02_sila_materialu,0]) |
| cylinder(h=D02_vyska_uchytky+0.01,r=D02_prumer_obruby/2,center=true); |
| } |
| |
| //uchyt na sloupek |
| translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+D02_sila_materialu+(D02_prumer_obruby)/2,D02_vyska_uchytky/2]) |
| rotate(a=[0,0,270]) |
| WINDGAUGE01A_D02(); |
| |
| } |
| |
| //otvor |
| translate([0,0,(D01_material_pod_zavitem+S01_vyska_spodniho_zavitu)/2]) |
| cylinder (h = D01_material_pod_zavitem+S01_vyska_spodniho_zavitu+0.02, r=((S01_prumer_vnitrni-S01_tolerance_zavit)-2*D01_material_za_zavitem)/2, center = true, $fn=100); |
| |
| translate([D02_dotahova_vzdalenost,-((D02_delka_celeho_uchytu/2-D02_prumer_obruby/2-D02_sila_materialu)/2+D02_prumer_obruby/2+D02_sila_materialu),D02_vyska_uchytky/4]){rotate([0,90,0]){cylinder(h=D02_sila_materialu+0.01,r=D02_prumer_uchytneho_sroubu/2);}} |
| |
| |
| |
| } |
| } |
| |
| WINDGAUGE01A_D01(); |
| |
| |
| |
| |