| 1,130 → 1,40 |
|---|
| $fn=40; // model faces resolution. |
| $fn=100; // model faces resolution. |
| include <../configuration.scad> |
| include <polyScrewThread_r1.scad> |
| PI=3.141592; |
| |
| WINDGAUGE01A_R01(); |
| |
| //Model lopatky |
| module WINDGAUGE01A_R01() |
| { |
| difference() |
| { |
| union() |
| { |
| //koule vrchní - kryt |
| translate([0,0,R01_vyska_preryti_statoru]) |
| sphere(d = (S01_prumer_vnitrni/2+5*S01_sila_materialu)*2, $fn=100); |
| |
| //spodní válec |
| cylinder (h = R01_vyska_preryti_statoru, r=S01_prumer_vnitrni/2+5*S01_sila_materialu, $fn=100); |
| |
| //lopatka 1 |
| translate([L01_hrana_drzaku_a/2,-(S01_prumer_vnitrni/2+2*S01_sila_materialu+L01_delka_uchytu+L01_prumer_lopatky/2),0]) |
| lopatka(); |
| |
| //lopatka 2 |
| rotate([0, 0, 120]) |
| translate([L01_hrana_drzaku_a/2,-(S01_prumer_vnitrni/2+2*S01_sila_materialu+L01_delka_uchytu+L01_prumer_lopatky/2),0]) |
| lopatka(); |
| |
| //lopatka 3 |
| rotate([0, 0, 240]) |
| translate([L01_hrana_drzaku_a/2,-(S01_prumer_vnitrni/2+2*S01_sila_materialu+L01_delka_uchytu+L01_prumer_lopatky/2),0]) |
| lopatka(); |
| } |
| |
| //Odečet spodního válce |
| translate([0,0,-(S01_prumer_vnitrni/2+2*S01_sila_materialu)]) |
| cylinder (h = R01_vyska_preryti_statoru+(S01_prumer_vnitrni/2+2*S01_sila_materialu), r=S01_prumer_vnitrni/2+4*S01_sila_materialu, $fn=100); |
| |
| //odecet koule |
| translate([0,0,R01_vyska_preryti_statoru]) |
| sphere(d = (S01_prumer_vnitrni/2+4*S01_sila_materialu)*2, $fn=100); |
| } |
| translate([0,0,R01_zavit_vyska+1]) |
| difference() |
| { |
| //kužel |
| |
| cylinder(h=10, r1=R03_prumer_zavitu/2+S01_sila_materialu, r2=5, center=false, $fn=100); |
| |
| cylinder(h=10-2*S01_sila_materialu, r1=R03_prumer_zavitu/2, r2=5-S01_sila_materialu, center=false,$fn=100); |
| |
| difference() |
| { |
| union() |
| { |
| //závit na ukotvení rotoru |
| //zakladni material |
| cylinder (h = (S01_prumer_vnitrni/2+2*S01_sila_materialu)+R01_vyska_preryti_statoru, r=(lozisko_prumer_vnejsi/2-1), $fn=100); |
| |
| vyztuhy(); |
| } |
| |
| //vnitrni zavit |
| translate([0,0,-5]) |
| screw_thread((11),3,55,R01_vyska_preryti_statoru+10,PI/2,2); |
| |
| //za závitem aby to slo tisknout |
| translate([0,0,R01_vyska_preryti_statoru+5]) |
| cylinder(h=(5), r1=(11)/2, r2=0, center=false, $fn=100); |
| |
| } |
| } |
| |
| module vyztuhy() |
| { |
| difference() |
| { |
| translate([0,0,R01_vyska_preryti_statoru]) |
| cylinder(h=(S01_prumer_vnitrni/2+4*S01_sila_materialu), r1=(lozisko_prumer_vnejsi/2-1), r2=(lozisko_prumer_vnejsi/2-1)+(S01_prumer_vnitrni/2+4*S01_sila_materialu)-R01_vyska_preryti_statoru, center=false, $fn=100); |
| |
| //vykousnutí 1 |
| translate([S01_sila_materialu/2,S01_sila_materialu/2,R01_vyska_preryti_statoru-0.005]) |
| cube([(lozisko_prumer_vnejsi/2-1)+(S01_prumer_vnitrni/2+4*S01_sila_materialu),(lozisko_prumer_vnejsi/2-1)+(S01_prumer_vnitrni/2+4*S01_sila_materialu),(S01_prumer_vnitrni/2+4*S01_sila_materialu)+0.01],center=false); |
| difference() |
| { |
| |
| |
| //válec na závit |
| cylinder (h = R01_zavit_vyska+1, r=R03_prumer_zavitu/2+S01_sila_materialu, $fn=100); |
| |
| //odečet závitu |
| translate([0,0,-10]) |
| screw_thread((R03_prumer_zavitu),S01_hloubka_zavitu,55,R01_zavit_vyska+12,PI/2,2); |
| |
| |
| //vykousnutí 2 |
| rotate([0, 0, 90]) |
| translate([S01_sila_materialu/2,S01_sila_materialu/2,R01_vyska_preryti_statoru-0.005]) |
| cube([(lozisko_prumer_vnejsi/2-1)+(S01_prumer_vnitrni/2+4*S01_sila_materialu),(lozisko_prumer_vnejsi/2-1)+(S01_prumer_vnitrni/2+4*S01_sila_materialu),(S01_prumer_vnitrni/2+4*S01_sila_materialu)+0.01],center=false); |
| |
| //vykousnutí 3 |
| rotate([0, 0, 180]) |
| translate([S01_sila_materialu/2,S01_sila_materialu/2,R01_vyska_preryti_statoru-0.005]) |
| cube([(lozisko_prumer_vnejsi/2-1)+(S01_prumer_vnitrni/2+4*S01_sila_materialu),(lozisko_prumer_vnejsi/2-1)+(S01_prumer_vnitrni/2+4*S01_sila_materialu),(S01_prumer_vnitrni/2+4*S01_sila_materialu)+0.01],center=false); |
| |
| //vykousnutí 4 |
| rotate([0, 0, 270]) |
| translate([S01_sila_materialu/2,S01_sila_materialu/2,R01_vyska_preryti_statoru-0.005]) |
| cube([(lozisko_prumer_vnejsi/2-1)+(S01_prumer_vnitrni/2+4*S01_sila_materialu),(lozisko_prumer_vnejsi/2-1)+(S01_prumer_vnitrni/2+4*S01_sila_materialu),(S01_prumer_vnitrni/2+4*S01_sila_materialu)+0.01],center=false); |
| difference() |
| { |
| translate([0,0,R01_vyska_preryti_statoru]) |
| sphere(d = (S01_prumer_vnitrni/2+12*S01_sila_materialu)*2, $fn=100); |
| |
| translate([0,0,R01_vyska_preryti_statoru]) |
| sphere(d = (S01_prumer_vnitrni/2+3*S01_sila_materialu)*2, $fn=100); |
| |
| } |
| } |
| } |
| } |
| |
| module lopatka() |
| { |
| difference() |
| { |
| union() |
| { |
| translate([0,0,L01_prumer_lopatky/2]) |
| sphere(d = L01_prumer_lopatky, $fn=100); |
| |
| translate([-L01_hrana_drzaku_a,0,0]) |
| cube([L01_hrana_drzaku_a,L01_delka_uchytu+L01_prumer_lopatky/2+10,L01_hrana_drzaku_b],center=false); |
| |
| //podpěra |
| translate([0,0,0]) |
| cylinder(h=(L01_prumer_lopatky/2), r1=L01_prumer_lopatky/3.5, r2=L01_prumer_lopatky/2, center=false, $fn=100); |
| |
| } |
| |
| |
| translate([0,0,L01_prumer_lopatky/2]) |
| sphere(d = L01_prumer_lopatky-L01_sila_materialu_lopatky*2, $fn=100); |
| |
| translate([0,-L01_prumer_lopatky,0]) |
| cube([L01_prumer_lopatky+0.01,2*(L01_delka_uchytu+L01_prumer_lopatky/2+10),L01_prumer_lopatky],center=false); |
| |
| } |
| //válec pro držení PCB |
| cylinder (h = R01_zavit_vyska+10, r=2, $fn=100); |
| |
| } |