| 5,8 → 5,9 |
|---|
| |
| //Drzak rotoru se závitem |
| |
| |
| |
| |
| |
| WINDGAUGE01A_R02(); |
| |
| module WINDGAUGE01A_R02() |
| 19,32 → 20,11 |
|---|
| |
| //kužel na závit |
| cylinder(h=R02_zavit_vyska, r1=S01_prumer_vnitrni/2+5*S01_sila_materialu, r2=R03_prumer_zavitu/2+S01_sila_materialu, center=false,$fn=100); |
| |
| //křídlo |
| translate([0,R02_vyska_kridla+R03_prumer_zavitu/2+S01_sila_materialu,0]) |
| rotate([0, 90, 0]) |
| difference() |
| { |
| //zakladní materiál |
| translate([0,0,0]) |
| cylinder (h = S01_sila_materialu, r=R02_vyska_kridla, $fn=100); |
| |
| translate([-R02_vyska_kridla,0,-0.01]) |
| cube([R02_vyska_kridla,R02_vyska_kridla,S01_sila_materialu+0.02],center=false); |
| |
| translate([0,-R02_vyska_kridla,-0.01]) |
| cube([R02_vyska_kridla,R02_vyska_kridla,S01_sila_materialu+0.02],center=false); |
| |
| translate([0,0,-0.01]) |
| cube([R02_vyska_kridla,R02_vyska_kridla,S01_sila_materialu+0.02],center=false); |
| |
| translate([-R02_vyska_kridla,-R03_prumer_zavitu/2-S01_sila_materialu+3,-0.01]) |
| cube([R02_vyska_kridla,R02_vyska_kridla,S01_sila_materialu+0.02],center=false); |
| |
| } |
| |
| |
| //kvádr pod tyčí |
| translate([-R02_hrana_drzaku/2,-(R02_delka_vyrovnnavaci_tyce+R03_prumer_zavitu/2+S01_sila_materialu),0]) |
| translate([-R02_hrana_drzaku/2,-(R02_delka_vyrovnnavaci_tyce+R03_prumer_zavitu/2+S01_sila_materialu),0]) |
| cube([R02_hrana_drzaku,R02_delka_vyrovnnavaci_tyce+R03_prumer_zavitu/2+S01_sila_materialu,R02_sila_materialu_pod_tyci],center=false); |
| |
| //prední tyč |
| 68,16 → 48,25 |
|---|
| translate([0,R02_delka_kridla+(S01_prumer_vnitrni/2+5*S01_sila_materialu)-R02_hrana_drzaku/2,0]) |
| cylinder (h = S01_sila_materialu, r=R02_hrana_drzaku/2, $fn=100); |
| |
| //ližiny pro křídlo |
| |
| |
| } |
| |
| translate([-(R02_sila_materialu_kridla+R02_sila_materialu_kridla_tolerance)/2,0,0]) |
| rotate ([0,-90,0]) |
| linear_extrude (height = S01_sila_materialu, convexity = 10) |
| polygon(points=[[0,R03_prumer_zavitu/2],[R02_zavit_vyska, R03_prumer_zavitu/2],[R02_zavit_vyska,R02_delka_kridla+(S01_prumer_vnitrni/2+5*S01_sila_materialu)-R02_hrana_drzaku/2],[0,R02_delka_kridla+(S01_prumer_vnitrni/2+5*S01_sila_materialu)-R02_hrana_drzaku/2]]); |
| |
| |
| |
| |
| translate([S01_sila_materialu+(R02_sila_materialu_kridla+R02_sila_materialu_kridla_tolerance)/2,0,0]) |
| rotate ([0,-90,0]) |
| linear_extrude (height = S01_sila_materialu, convexity = 10) |
| polygon(points=[[0,R03_prumer_zavitu/2],[R02_zavit_vyska, R03_prumer_zavitu/2],[R02_zavit_vyska,R02_delka_kridla+(S01_prumer_vnitrni/2+5*S01_sila_materialu)-R02_hrana_drzaku/2],[0,R02_delka_kridla+(S01_prumer_vnitrni/2+5*S01_sila_materialu)-R02_hrana_drzaku/2]]); |
| } |
| |
| //odečet závitu |
| translate([0,0,-10]) |
| screw_thread((R03_prumer_zavitu),S01_hloubka_zavitu,55,R04_zavit_vyska+R02_zavit_vyska+R01_zavit_vyska,PI/2,2); |
| screw_thread((R03_prumer_zavitu),S01_hloubka_zavitu,55,R04_zavit_vyska+R02_zavit_vyska+R01_zavit_vyska+10,PI/2,2); |
| |
| //otvor na hlavu šroubu |
| |