| 7,43 → 7,39 |
|---|
| |
| //dutinka pro upevneni rotoru |
| module rotor3 (sila_pod_loziskem,delka_hridele,lozisko_prumer_vnitrni,lozisko_prekryv) |
| { |
| difference() |
| { |
| { |
| difference() |
| { |
| |
| |
| //dotahovací kroužek |
| translate([0,0,0]) |
| cylinder (h = sila_pod_loziskem+delka_hridele+2, r=(lozisko_prumer_vnitrni+2*lozisko_prekryv)/2, center = true, $fn=100); |
| //dotahovací kroužek |
| translate([0,0,0]) |
| cylinder (h = sila_pod_loziskem+delka_hridele+2, r=(lozisko_prumer_vnitrni+2*lozisko_prekryv)/2, center = true, $fn=100); |
| |
| cylinder (h = sila_pod_loziskem+delka_hridele+2+0.1, r=((lozisko_prumer_vnitrni+0.2)/2), center = true, $fn=100); |
| |
| |
| } |
| } |
| cylinder (h = sila_pod_loziskem+delka_hridele+2+0.1, r=((lozisko_prumer_vnitrni+0.2)/2), center = true, $fn=100); |
| |
| } |
| } |
| |
| |
| module rotor4 (vyska_pod_magnetem,magnet_zapusteni,magnet_prumer,vyska_hlavy_sroubu,prumer_hlavy_sroubu,prumer_sroubu) |
| { |
| difference() |
| { |
| |
| |
| //segment pro sroub a magnet |
| translate([0,0,0]) |
| cylinder (h = vyska_pod_magnetem+magnet_zapusteni, r=(magnet_prumer+2)/2, center = true, $fn=100); |
| { |
| difference() |
| { |
| //segment pro sroub a magnet |
| translate([0,0,0]) |
| cylinder (h = vyska_pod_magnetem+magnet_zapusteni, r=(magnet_prumer+2)/2, center = true, $fn=100); |
| |
| //otvor pro magnet |
| translate([0,0,vyska_pod_magnetem/2+0.1]) |
| cylinder (h = magnet_zapusteni, r=((magnet_prumer+0.2)/2), center = true, $fn=100); |
| //otvor pro magnet |
| translate([0,0,vyska_pod_magnetem/2+0.1]) |
| cylinder (h = magnet_zapusteni, r=((magnet_prumer+0.2)/2), center = true, $fn=100); |
| |
| //zapusteni uchytného sroubu |
| translate([0,0,(vyska_pod_magnetem-vyska_hlavy_sroubu-1)/2+0.1]) |
| cylinder (h = vyska_hlavy_sroubu+1, r=((prumer_hlavy_sroubu+0.2)/2), center = true, $fn=100); |
| //zapusteni uchytného sroubu |
| translate([0,0,(vyska_pod_magnetem-vyska_hlavy_sroubu-1)/2+0.1]) |
| cylinder (h = vyska_hlavy_sroubu+1, r=((prumer_hlavy_sroubu+0.2)/2), center = true, $fn=100); |
| |
| //otvor pro sroub |
| cylinder (h = vyska_pod_magnetem+magnet_zapusteni+0.1, r=(prumer_sroubu)/2, center = true, $fn=100); |
| } |
| } |
| //otvor pro sroub |
| cylinder (h = vyska_pod_magnetem+magnet_zapusteni+0.1, r=(prumer_sroubu)/2, center = true, $fn=100); |
| } |
| } |
| |
| |