| 5,6 → 5,7 |
|---|
| vyska_rotoru2=5; |
| prumer_sroubu=3.2; |
| prumer_hlavy_sroubu=6; |
| vyska_hlavy_sroubu=4; |
| vyska_matky=3; |
| sirka_matky=6; |
| prumer_orechu=10; |
| 26,7 → 27,7 |
|---|
| |
| //stator3 |
| stator3_sila_steny=2; |
| stator3_vzdalenost_od_steny=2; //definuje vzdalenost hlavy sroubu od steny statrou 4 |
| stator3_vzdalenost_od_steny=1; //definuje vzdalenost hlavy sroubu od steny statrou 4 |
| |
| vule1=2; //vůle mezi statorem a rotorem ze strany |
| |
| 83,17 → 84,30 |
|---|
| |
| //otvory pro uchyceni senzoru |
| //otvor pro sroub 1 |
| rotate(a=[0,0,0]) |
| |
| translate([(vzdalenost_der_x/2),-vzdalenost_der_y/2,0]) |
| |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_sroubu/2, center = true, $fn=100); |
| |
| //otvor pro sroub 1 |
| translate([(vzdalenost_der_x/2),-vzdalenost_der_y/2,(lozisko_vyska+sila_pod_loziskem-vyska_hlavy_sroubu)/2]) |
| |
| cylinder (h = vyska_hlavy_sroubu+0.1, r=prumer_hlavy_sroubu/2, center = true, $fn=100); |
| |
| |
| |
| //otvor pro sroub 2 |
| rotate(a=[0,0,0]) |
| translate([(-vzdalenost_der_x/2),-vzdalenost_der_y/2,0]) |
| |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_sroubu/2, center = true, $fn=100); |
| |
| translate([(-vzdalenost_der_x/2),-vzdalenost_der_y/2,(lozisko_vyska+sila_pod_loziskem-vyska_hlavy_sroubu)/2]) |
| |
| cylinder (h = vyska_hlavy_sroubu+0.1, r=prumer_hlavy_sroubu/2, center = true, $fn=100); |
| |
| |
| |
| |
| //otvor pro sroub 1 |
| rotate(a=[0,0,0]) |
| translate([(vzdalenost_der_x/2),vzdalenost_der_y/2,0]) |
| 100,6 → 114,11 |
|---|
| |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_sroubu/2, center = true, $fn=100); |
| |
| translate([(vzdalenost_der_x/2),vzdalenost_der_y/2,(lozisko_vyska+sila_pod_loziskem-vyska_hlavy_sroubu)/2]) |
| |
| cylinder (h = vyska_hlavy_sroubu+0.1, r=prumer_hlavy_sroubu/2, center = true, $fn=100); |
| |
| |
| //otvor pro sroub 1 |
| rotate(a=[0,0,0]) |
| translate([(-vzdalenost_der_x/2),vzdalenost_der_y/2,0]) |
| 106,7 → 125,9 |
|---|
| |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_sroubu/2, center = true, $fn=100); |
| |
| translate([(-vzdalenost_der_x/2),vzdalenost_der_y/2,(lozisko_vyska+sila_pod_loziskem-vyska_hlavy_sroubu)/2]) |
| |
| cylinder (h = vyska_hlavy_sroubu+0.1, r=prumer_hlavy_sroubu/2, center = true, $fn=100); |
| |
| |
| |
| 116,9 → 137,19 |
|---|
| //otvory pro uchyceni stator 3 |
| //otvor pro sroub 1 |
| translate([0,(prumer_rotoru1-2*sila_materialu-2*vule1-2*stator3_sila_steny-prumer_hlavy_sroubu-2*stator3_vzdalenost_od_steny)/2,0]) |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=3, center = true, $fn=100); |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_sroubu/2, center = true, $fn=100); |
| |
| translate([0,(prumer_rotoru1-2*sila_materialu-2*vule1-2*stator3_sila_steny-prumer_hlavy_sroubu-2*stator3_vzdalenost_od_steny)/2,2]) |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_hlavy_sroubu/2, center = true, $fn=100); |
| |
| //otvor pro sroub 2 |
| translate([0,-(prumer_rotoru1-2*sila_materialu-2*vule1-2*stator3_sila_steny-prumer_hlavy_sroubu-2*stator3_vzdalenost_od_steny)/2,0]) |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_sroubu/2, center = true, $fn=100); |
| |
| translate([0,-(prumer_rotoru1-2*sila_materialu-2*vule1-2*stator3_sila_steny-prumer_hlavy_sroubu-2*stator3_vzdalenost_od_steny)/2,2]) |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_hlavy_sroubu/2, center = true, $fn=100); |
| |
| |
| } |
| |
| |