5,8 → 5,8 |
|
PI=3.141592; |
|
WINDGAUGE02A_S01(); |
|
|
module WINDGAUGE02A_S01() |
{ |
difference() |
44,9 → 44,79 |
} |
} |
|
difference() |
{ |
WINDGAUGE02A_S01(); |
|
cube(300); // cut to show internal relief |
|
} |
|
|
|
|
|
/* |
module WINDGAUGE02A_S01(R02_vzdalenost_mezi_uchyty_lopatek,L01_sila_zapusteni_drzaku,L01_hloubka_zapusteni,S01_vyska_zuzene_casti,S01_vyska_na_elektroniku,S01_vyska_zavitu_na_nasroubovani_drzaku,S01_vyska_prechodu,vule_mezi_statorem_rotorem,S01_vyska_zavitu_na_nasroubovani_drzaku,S01_sila_materialu) |
{ |
|
//zuzena cas komponentu |
|
translate([0,0,(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+S01_vyska_zuzene_casti)/2+S01_vyska_prechodu]) |
|
difference() |
{ |
cylinder (h = S01_vyska_zuzene_casti, r=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem+2*S01_sila_materialu)/2, center = true, $fn=100); |
|
translate([0,0,-S01_vyska_zuzene_casti/2+S01_vyska_zuzene_casti-R02_sila_mateiralu_pod_lopatkami-S01_vyska_komponentu_na_lozisko]) |
|
screw_thread((R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem),S01_hloubka_zavitu,55,S01_vyska_zuzene_casti+0.01,PI/2,2); |
|
translate([0,0,-(S01_vyska_zuzene_casti/2)+(S01_vyska_zuzene_casti-R02_sila_mateiralu_pod_lopatkami-S01_vyska_komponentu_na_lozisko)/2]) |
cylinder (h = S01_vyska_zuzene_casti-R02_sila_mateiralu_pod_lopatkami-S01_vyska_komponentu_na_lozisko+0.01, r=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem)/2, center = true, $fn=100); |
|
|
//translate([0,0,(stator3_vyska-stator3_vyska_prekryti)/2]) |
|
|
} |
|
difference() |
{ |
|
translate([0,0,(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+S01_vyska_prechodu)/2]) |
|
cylinder(h=S01_vyska_prechodu,r1=(S01_prumer_zavitu+2*S01_sila_materialu)/2, r2=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem+2*S01_sila_materialu)/2, center=true); |
|
|
translate([0,0,(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+S01_vyska_prechodu)/2]) |
|
cylinder(h=S01_vyska_prechodu,r1=(S01_prumer_zavitu)/2, r2=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem)/2, center=true); |
|
|
|
} |
|
|
//spodni cast se zavitem |
|
difference() |
{ |
cylinder (h = S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko, r=(S01_prumer_zavitu+2*S01_sila_materialu)/2, center = true, $fn=100); |
|
translate([0,0,-(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko)/2]) |
// metric_thread (diameter=S01_prumer_zavitu, pitch=1, length=S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+0.01, internal=true, n_starts=6); |
|
screw_thread(S01_prumer_zavitu,4,55,S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+0.01,PI/2,2); |
|
} |
|
} |
*/ |
|
|
|
|
|
|
|