| 8,7 → 8,7 |
|---|
| |
| |
| |
| module WINDGAUGE02A_D01(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu,S01_tolerance_zavit) |
| module WINDGAUGE02A_D01() |
| { |
| |
| difference() |
| 18,22 → 18,22 |
|---|
| { |
| //zavit |
| translate([0,0,D01_material_pod_zavitem]) |
| screw_thread(S01_prumer_zavitu-S01_tolerance_zavit,4,55,S01_vyska_komponentu_na_lozisko,PI/2,2); |
| screw_thread(S01_prumer_vnitrni-S01_tolerance_zavit,4,55,S01_vyska_spodniho_zavitu,PI/2,2); |
| |
| //spodní valec |
| translate([0,0,D01_material_pod_zavitem/2]) |
| cylinder (h = D01_material_pod_zavitem, r=(S01_prumer_zavitu+D01_material_pred_zavitem*2)/2, center = true, $fn=100); |
| cylinder (h = D01_material_pod_zavitem, r=(S01_prumer_vnitrni-S01_tolerance_zavit+D01_material_pred_zavitem*2)/2, center = true, $fn=100); |
| |
| //uchyt na tyc |
| translate([0,D01_delka_tyce/2+S01_prumer_zavitu/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) |
| translate([0,D01_delka_tyce/2+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) |
| cube([D01_sirka_tyce,D01_delka_tyce,D01_material_pod_zavitem],center=true); |
| //uchyt na tyc ovalna cast |
| translate([0,S01_prumer_zavitu/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) |
| translate([0,(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) |
| cube([D01_sirka_tyce,D01_material_za_zavitem+D01_material_pred_zavitem,D01_material_pod_zavitem],center=true); |
| |
| |
| //material kolem uchytu na sloupek |
| translate([0,D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+(D02_sila_materialu+D02_prumer_obruby/2)/2-D02_dotahova_vzdalenost,D01_material_pod_zavitem/2]) |
| translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+(D02_sila_materialu+D02_prumer_obruby/2)/2-D02_dotahova_vzdalenost,D01_material_pod_zavitem/2]) |
| difference() |
| { |
| cube([D01_sirka_tyce,D02_sila_materialu+D02_prumer_obruby/2,D01_material_pod_zavitem],center=true); |
| 46,20 → 46,20 |
|---|
| |
| //uchyt na sloupek |
| |
| translate([0,D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+D02_sila_materialu+(D02_prumer_obruby)/2,D02_vyska_uchytky/2]) |
| translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+D02_sila_materialu+(D02_prumer_obruby)/2,D02_vyska_uchytky/2]) |
| rotate(a=[0,0,270]) |
| WINDGAUGE02A_D02(D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu); |
| WINDGAUGE02A_D02(); |
| |
| } |
| |
| //otvor |
| translate([0,0,(D01_material_pod_zavitem+S01_vyska_komponentu_na_lozisko)/2]) |
| cylinder (h = D01_material_pod_zavitem+S01_vyska_komponentu_na_lozisko+0.02, r=(S01_prumer_zavitu-2*D01_material_za_zavitem)/2, center = true, $fn=100); |
| translate([0,0,(D01_material_pod_zavitem+S01_vyska_spodniho_zavitu)/2]) |
| cylinder (h = D01_material_pod_zavitem+S01_vyska_spodniho_zavitu+0.02, r=((S01_prumer_vnitrni-S01_tolerance_zavit)-2*D01_material_za_zavitem)/2, center = true, $fn=100); |
| |
| } |
| } |
| |
| WINDGAUGE02A_D01(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu,S01_tolerance_zavit); |
| WINDGAUGE02A_D01(); |
| |
| |
| |