| 1,64 → 1,40 |
|---|
| $fn=40; // model faces resolution. |
| $fn=100; // model faces resolution. |
| include <../configuration.scad> |
| |
| include <polyScrewThread_r1.scad> |
| PI=3.141592; |
| |
| WINDGAUGE02A_R02(); |
| |
| module WINDGAUGE02A_R02() |
| { |
| |
| |
| |
| |
| difference() |
| //setihrana matice |
| difference() |
| { |
| |
| union() |
| union() |
| { |
| cylinder (h = R02_sila_mateiralu_pod_lopatkami+L01_hloubka_zapusteni_drzaku, r=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni)/2, center = true, $fn=100); |
| |
| //valec pod zavitem |
| translate([0,0,(L01_hloubka_zapusteni_drzaku+R02_sila_mateiralu_pod_lopatkami)/2]) |
| cylinder (h = L01_hloubka_zapusteni_drzaku+L01_hrana_drzaku_b-1, r=(prumer_osicky+3*S01_sila_materialu)/2, $fn=100); |
| |
| //zavit |
| translate([0,0,L01_hloubka_zapusteni_drzaku+L01_hrana_drzaku_b+(L01_hloubka_zapusteni_drzaku+R02_sila_mateiralu_pod_lopatkami)/2-3]) |
| screw_thread(prumer_osicky+3*S01_sila_materialu,S01_hloubka_zavitu,55,2*R02_vyska_matky+3,PI/2,2); |
| //závit |
| screw_thread((11-S01_tolerance_zavit),3,55,R01_vyska_preryti_statoru,PI/2,2); |
| |
| |
| } |
| //otvor pro lopatku 1 |
| rotate(a=[0,0,0]) |
| //spodní podložka |
| translate([0,0,-R01_mezera_mezi_statorem_rotorem/2]) |
| cylinder (h = R01_mezera_mezi_statorem_rotorem, r=(lozisko_prumer_vnitrni+2*lozisko_prekryv+2)/2, center = true, $fn=100); |
| } |
| |
| |
| translate([(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni)/2-L01_hloubka_zapusteni-L01_sila_zapusteni_drzaku/2,0,((R02_sila_mateiralu_pod_lopatkami+L01_hloubka_zapusteni_drzaku)/2)-L01_hloubka_zapusteni_drzaku/2]) |
| cube([L01_sila_zapusteni_drzaku+L01_tolerance_drzaku,L01_hrana_drzaku_a+L01_tolerance_drzaku,L01_hloubka_zapusteni_drzaku],true); |
| |
| |
| |
| //otvor pro lopatku 2 |
| rotate(a=[0,0,120]) |
| |
| translate([(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni)/2-L01_hloubka_zapusteni-L01_sila_zapusteni_drzaku/2,0,((R02_sila_mateiralu_pod_lopatkami+L01_hloubka_zapusteni_drzaku)/2)-L01_hloubka_zapusteni_drzaku/2]) |
| cube([L01_sila_zapusteni_drzaku+L01_tolerance_drzaku,L01_hrana_drzaku_a+L01_tolerance_drzaku,L01_hloubka_zapusteni_drzaku],true); |
| |
| //otvor |
| translate([0,0,-R01_mezera_mezi_statorem_rotorem-0.05]) |
| cylinder (h = R01_vyska_preryti_statoru+R01_mezera_mezi_statorem_rotorem+0.1, r=prumer_osicky/2, $fn=100); |
| |
| |
| |
| |
| } |
| |
| |
| //otvor pro lopatku 3 |
| rotate(a=[0,0,240]) |
| |
| translate([(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni)/2-L01_hloubka_zapusteni-L01_sila_zapusteni_drzaku/2,0,((R02_sila_mateiralu_pod_lopatkami+L01_hloubka_zapusteni_drzaku)/2)-L01_hloubka_zapusteni_drzaku/2]) |
| cube([L01_sila_zapusteni_drzaku+L01_tolerance_drzaku,L01_hrana_drzaku_a+L01_tolerance_drzaku,L01_hloubka_zapusteni_drzaku],true); |
| //otvor na hřídelku |
| |
| cylinder (h = R02_sila_mateiralu_pod_lopatkami+L01_hloubka_zapusteni_drzaku+0.1+60, r=prumer_osicky/2, center = true, $fn=100); |
| /* |
| //otvor pro pomocnou trubicku |
| translate([0,0,-(((R02_sila_mateiralu_pod_lopatkami+L01_hloubka_zapusteni_drzaku)/2)-zapusteni_pomocne_trubicky/2)]) |
| cylinder (h = zapusteni_pomocne_trubicky, r=prumer_pomocne_trubicky/2, center = true, $fn=100); |
| */ |
| } |
| |
| } |
| |
| WINDGAUGE02A_R02(); |
| |
| |