/Modules/Mechanical/WINDGAUGE02A/CAD/SRC/WINDGAUGE02A_S01.scad/WINDGAUGE02A_S01.scad
5,8 → 5,8
 
PI=3.141592;
 
WINDGAUGE02A_S01();
 
 
module WINDGAUGE02A_S01()
{
difference()
44,79 → 44,9
}
}
 
difference()
{
WINDGAUGE02A_S01();
 
cube(300); // cut to show internal relief
 
}
 
 
 
 
 
/*
module WINDGAUGE02A_S01(R02_vzdalenost_mezi_uchyty_lopatek,L01_sila_zapusteni_drzaku,L01_hloubka_zapusteni,S01_vyska_zuzene_casti,S01_vyska_na_elektroniku,S01_vyska_zavitu_na_nasroubovani_drzaku,S01_vyska_prechodu,vule_mezi_statorem_rotorem,S01_vyska_zavitu_na_nasroubovani_drzaku,S01_sila_materialu)
{
//zuzena cas komponentu
translate([0,0,(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+S01_vyska_zuzene_casti)/2+S01_vyska_prechodu])
difference()
{
cylinder (h = S01_vyska_zuzene_casti, r=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem+2*S01_sila_materialu)/2, center = true, $fn=100);
translate([0,0,-S01_vyska_zuzene_casti/2+S01_vyska_zuzene_casti-R02_sila_mateiralu_pod_lopatkami-S01_vyska_komponentu_na_lozisko])
screw_thread((R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem),S01_hloubka_zavitu,55,S01_vyska_zuzene_casti+0.01,PI/2,2);
translate([0,0,-(S01_vyska_zuzene_casti/2)+(S01_vyska_zuzene_casti-R02_sila_mateiralu_pod_lopatkami-S01_vyska_komponentu_na_lozisko)/2])
cylinder (h = S01_vyska_zuzene_casti-R02_sila_mateiralu_pod_lopatkami-S01_vyska_komponentu_na_lozisko+0.01, r=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem)/2, center = true, $fn=100);
 
//translate([0,0,(stator3_vyska-stator3_vyska_prekryti)/2])
}
 
difference()
{
translate([0,0,(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+S01_vyska_prechodu)/2])
cylinder(h=S01_vyska_prechodu,r1=(S01_prumer_zavitu+2*S01_sila_materialu)/2, r2=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem+2*S01_sila_materialu)/2, center=true);
translate([0,0,(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+S01_vyska_prechodu)/2])
cylinder(h=S01_vyska_prechodu,r1=(S01_prumer_zavitu)/2, r2=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem)/2, center=true);
}
 
 
//spodni cast se zavitem
 
difference()
{
cylinder (h = S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko, r=(S01_prumer_zavitu+2*S01_sila_materialu)/2, center = true, $fn=100);
translate([0,0,-(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko)/2])
// metric_thread (diameter=S01_prumer_zavitu, pitch=1, length=S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+0.01, internal=true, n_starts=6);
screw_thread(S01_prumer_zavitu,4,55,S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+0.01,PI/2,2);
}
 
}
*/