| 1,112 → 1,63 |
|---|
| $fn=40; // model faces resolution. |
| include <../configuration.scad> |
| |
| use <zavity.scad> |
| |
| module WINDGAUGE02A_S01(R02_vzdalenost_mezi_uchyty_lopatek,L01_sila_zapusteni_drzaku,L01_hloubka_zapusteni,S01_vyska_zuzene_casti) |
| { |
| difference() |
| { |
| cylinder (h = S01_vyska_zuzene_casti, r=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem+2*S01_sila_materialu)/2, center = true, $fn=100); |
| |
| |
| cylinder (h = S01_vyska_zuzene_casti+0.01, r=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem)/2, center = true, $fn=100); |
| |
| |
| //translate([0,0,(stator3_vyska-stator3_vyska_prekryti)/2]) |
| |
| |
| } |
| |
| difference() |
| { |
| cylinder (h = S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko, r=(S01_prumer_zavitu+2*S01_sila_materialu)/2, center = true, $fn=10); |
| |
| metric_thread (diameter=S01_prumer_zavitu, pitch=1, length=S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko, internal=true, n_starts=6); |
| |
| |
| |
| } |
| } |
| |
| |
| |
| module stator3(stator3_vyska,prumer_rotoru1,lozisko_vyska,sila_pod_loziskem,sila_materialu,vule1,stator3_sila_steny, |
| stator3_vyska_prekryti,prumer_hlavy_sroubu,stator3_vzdalenost_od_steny,lozisko_vyska,prumer_sroubu,roztec_sroubu,uchyt_prumer_sroubu,vyska_stator4,kabel_prumer) |
| { |
| difference() |
| { |
| cylinder (h = stator3_vyska, r=(prumer_rotoru1)/2, center = true, $fn=100); |
| |
| translate([0,0,(stator3_vyska-lozisko_vyska-sila_pod_loziskem)/2]) |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=(prumer_rotoru1-2*sila_materialu-2*vule1-stator3_sila_steny)/2, center = true, $fn=100); |
| |
| cylinder (h = stator3_vyska+0.1, r=(prumer_rotoru1-2*sila_materialu-2*vule1-2*stator3_sila_steny-1)/2, center = true, $fn=100); |
| |
| |
| translate([0,0,(stator3_vyska-stator3_vyska_prekryti)/2]) |
| difference() |
| { |
| |
| cylinder (h = stator3_vyska_prekryti+0.1, r=(prumer_rotoru1+0.1)/2, center = true, $fn=100); |
| |
| cylinder (h = stator3_vyska_prekryti+0.1, r=(prumer_rotoru1-2*sila_materialu-2*vule1)/2, center = true, $fn=100); |
| |
| } |
| |
| //otvory pro uchyceni stator 3 |
| //otvor pro sroub 1 |
| translate([0,(prumer_rotoru1-2*sila_materialu-2*vule1-2*stator3_sila_steny-prumer_hlavy_sroubu-2*stator3_vzdalenost_od_steny)/2,0]) |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_sroubu/2, center = true, $fn=100); |
| |
| translate([0,(prumer_rotoru1-2*sila_materialu-2*vule1-2*stator3_sila_steny-prumer_hlavy_sroubu-2*stator3_vzdalenost_od_steny)/2,2]) |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_hlavy_sroubu/2, center = true, $fn=100); |
| |
| //otvor pro sroub 2 |
| translate([0,-(prumer_rotoru1-2*sila_materialu-2*vule1-2*stator3_sila_steny-prumer_hlavy_sroubu-2*stator3_vzdalenost_od_steny)/2,0]) |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_sroubu/2, center = true, $fn=100); |
| |
| translate([0,-(prumer_rotoru1-2*sila_materialu-2*vule1-2*stator3_sila_steny-prumer_hlavy_sroubu-2*stator3_vzdalenost_od_steny)/2,2]) |
| cylinder (h = lozisko_vyska+sila_pod_loziskem+0.1, r=prumer_hlavy_sroubu/2, center = true, $fn=100); |
| } |
| |
| |
| //dno stator3 |
| |
| translate([0,0,-(stator3_vyska-stator3_sila_steny)/2]) |
| difference() |
| { |
| cylinder (h = stator3_sila_steny, r=(prumer_rotoru1)/2, center = true, $fn=100); |
| |
| //otvory pro uchyceni stator 3 |
| //otvor pro sroub 1 |
| translate([0,(prumer_rotoru1-2*sila_materialu-2*vule1-2*stator3_sila_steny-prumer_hlavy_sroubu-2*stator3_vzdalenost_od_steny)/2,0]) |
| cylinder (h = stator3_sila_steny+0.1, r=prumer_sroubu/2, center = true, $fn=100); |
| |
| |
| |
| //otvor pro sroub 2 |
| translate([0,-(prumer_rotoru1-2*sila_materialu-2*vule1-2*stator3_sila_steny-prumer_hlavy_sroubu-2*stator3_vzdalenost_od_steny)/2,0]) |
| cylinder (h = stator3_sila_steny+0.1, r=prumer_sroubu/2, center = true, $fn=100); |
| |
| //srouby pro uchycení anemometru |
| translate([roztec_sroubu/2,roztec_sroubu/2,0]) |
| cylinder (h = stator3_sila_steny+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100); |
| |
| translate([-roztec_sroubu/2,roztec_sroubu/2,0]) |
| cylinder (h = stator3_sila_steny+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100); |
| |
| translate([roztec_sroubu/2,-roztec_sroubu/2,0]) |
| cylinder (h = stator3_sila_steny+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100); |
| |
| translate([-roztec_sroubu/2,-roztec_sroubu/2,0]) |
| cylinder (h = stator3_sila_steny+0.1, r=uchyt_prumer_sroubu/2, center = true, $fn=100); |
| |
| //dira na kabel |
| cylinder (h = vyska_stator4+0.1, r=(kabel_prumer/2+0.1), center = true, $fn=100); |
| } |
| } |
| |
| WINDGAUGE02A_S01(R02_vzdalenost_mezi_uchyty_lopatek,L01_sila_zapusteni_drzaku,L01_hloubka_zapusteni,S01_vyska_zuzene_casti); |
| |
| |
| $fn=40; // model faces resolution. |
| include <../configuration.scad> |
| |
| use <zavity.scad> |
| |
| module WINDGAUGE02A_S01(R02_vzdalenost_mezi_uchyty_lopatek,L01_sila_zapusteni_drzaku,L01_hloubka_zapusteni,S01_vyska_zuzene_casti,S01_vyska_na_elektroniku,S01_vyska_zavitu_na_nasroubovani_drzaku,S01_vyska_prechodu,vule_mezi_statorem_rotorem,S01_vyska_zavitu_na_nasroubovani_drzaku) |
| { |
| |
| //zuzena cas komponentu |
| |
| translate([0,0,(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+S01_vyska_zuzene_casti)/2+S01_vyska_prechodu]) |
| |
| difference() |
| { |
| cylinder (h = S01_vyska_zuzene_casti, r=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem+2*S01_sila_materialu)/2, center = true, $fn=100); |
| |
| |
| cylinder (h = S01_vyska_zuzene_casti+0.01, r=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem)/2, center = true, $fn=100); |
| |
| |
| //translate([0,0,(stator3_vyska-stator3_vyska_prekryti)/2]) |
| |
| |
| } |
| |
| difference() |
| { |
| |
| translate([0,0,(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+S01_vyska_prechodu)/2]) |
| |
| cylinder(h=S01_vyska_prechodu,r1=(S01_prumer_zavitu+2*S01_sila_materialu)/2, r2=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem+2*S01_sila_materialu)/2, center=true); |
| |
| |
| translate([0,0,(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+S01_vyska_prechodu)/2]) |
| |
| cylinder(h=S01_vyska_prechodu,r1=(S01_prumer_zavitu)/2, r2=(R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem)/2, center=true); |
| |
| |
| |
| } |
| |
| |
| //spodni cast se zavitem |
| |
| difference() |
| { |
| cylinder (h = S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko, r=(S01_prumer_zavitu+2*S01_sila_materialu)/2, center = true, $fn=100); |
| |
| translate([0,0,-(S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko)/2]) |
| metric_thread (diameter=S01_prumer_zavitu, pitch=1, length=S01_vyska_na_elektroniku+S01_vyska_zavitu_na_nasroubovani_drzaku+2*S01_vyska_komponentu_na_lozisko+0.01, internal=true, n_starts=6); |
| |
| |
| |
| } |
| } |
| |
| |
| |
| |
| |
| //WINDGAUGE02A_S01(R02_vzdalenost_mezi_uchyty_lopatek,L01_sila_zapusteni_drzaku,L01_hloubka_zapusteni,S01_vyska_zuzene_casti,S01_vyska_na_elektroniku,S01_vyska_zavitu_na_nasroubovani_drzaku,S01_vyska_prechodu,vule_mezi_statorem_rotorem,S01_vyska_zavitu_na_nasroubovani_drzaku); |
| |
| |