| 1,52 → 1,161 |
|---|
| $fn=40; // model faces resolution. |
| include <../configuration.scad> |
| |
| |
| include <polyScrewThread_r1.scad> |
| |
| PI=3.141592; |
| |
| WINDGAUGE02A_S01(); |
| |
| //Držák ložisek, rotoru, senzoru |
| |
| module WINDGAUGE02A_S01() |
| { |
| difference() |
| { |
| union() |
| { |
| //základní válec |
| cylinder (h = S01_vyska, r=(S01_prumer_vnitrni)/2+S01_sila_materialu, $fn=100); |
| { |
| //valec se zavitem |
| union() |
| { |
| difference() |
| { |
| union() |
| { |
| translate([0,0,S01_sila_materialu]) |
| screw_thread((S01_prumer_vnitrni-S01_tolerance_zavit),S01_hloubka_zavitu,55,S01_vyska_horni_zavit,PI/2,2); |
| |
| //spodní doraz |
| cylinder (h = S01_sila_materialu, r=S01_prumer_vnitrni/2+5/2*S01_sila_materialu, $fn=100); |
| |
| |
| //krycí ovál - usnadnění povolení |
| difference() |
| { |
| cylinder (h = R01_vyska_preryti_statoru+5, r=S01_prumer_vnitrni/2+5/2*S01_sila_materialu, $fn=100); |
| |
| cylinder (h = R01_vyska_preryti_statoru+5+0.01, r=S01_prumer_vnitrni/2+3/2*S01_sila_materialu, $fn=100); |
| |
| } |
| } |
| |
| //odstranění vnitřní výplně |
| translate([0,0,S01_sila_materialu]) |
| cylinder (h = S01_vyska_horni_zavit+0.01, r=S01_prumer_vnitrni/2-S01_hloubka_zavitu/2-S01_sila_materialu, $fn=100); |
| |
| //otvor na ložisko |
| translate([0,0,S01_sila_materialu/2]) |
| cylinder (h = S01_sila_materialu+0.01, r=(lozisko_prumer_vnejsi+0.2)/2, center = true, $fn=100); |
| //otvory na hlavu šroubu ve dně |
| //otvor na hlavu šroubu 1 |
| translate([-senzor_delka/2,-senzor_sirka/2,(lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky)/2]) |
| cylinder (h = lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky+0.01, r=(prumer_hlavy_sroubu)/2, center = true, $fn=100); |
| |
| //otvor na šroub 2 |
| translate([senzor_delka/2,-senzor_sirka/2,(lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky)/2]) |
| cylinder (h = lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky+0.01, r=(prumer_hlavy_sroubu)/2, center = true, $fn=100); |
| |
| //otvor na šroub 3 |
| translate([senzor_delka/2,senzor_sirka/2,(lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky)/2]) |
| cylinder (h = lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky+0.01, r=(prumer_hlavy_sroubu)/2, center = true, $fn=100); |
| |
| //otvor na šroub 4 |
| translate([-senzor_delka/2,senzor_sirka/2,(lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky)/2]) |
| cylinder (h = lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky+0.01, r=(prumer_hlavy_sroubu)/2, center = true, $fn=100); |
| |
| } |
| |
| //horní závit |
| translate([0,0,S01_vyska-S01_vyska_horni_zavit]) |
| screw_thread(S01_prumer_vnitrni,S01_hloubka_zavitu,55,S01_vyska_horni_zavit+5,PI/2,2); |
| |
| //otvor na ložisko |
| difference() |
| { |
| translate([0,0,(R01_vyska_preryti_statoru+2*lozisko_vyska)/2+S01_sila_materialu]) |
| cylinder (h = R01_vyska_preryti_statoru+2*lozisko_vyska, r=(lozisko_prumer_vnejsi+2*S01_sila_materialu)/2, center = true, $fn=100); |
| |
| translate([0,0,(R01_vyska_preryti_statoru+2*lozisko_vyska)/2+S01_sila_materialu]) |
| cylinder (h = R01_vyska_preryti_statoru+2*lozisko_vyska+0.01, r=(lozisko_prumer_vnejsi+0.2)/2, center = true, $fn=100); |
| |
| //otvory na hlavy sroubu v uchytu loziska |
| translate([-senzor_delka/2,-senzor_sirka/2,0]) |
| { |
| cylinder (h = vyska_hlavy_sroubu, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu]) |
| cylinder(h=2+0.02, r1=(prumer_hlavy_sroubu)/2, r2=(prumer_sroubu+0.2)/2); |
| } |
| |
| //otvor na drzak rj11 |
| translate([0,0,S01_vyska_spodniho_zavitu+S01_sila_drzaku_RJ11-0.3]) |
| cylinder( 2*S01_sila_drzaku_RJ11, d1=(S01_prumer_vnitrni)-1-1.5*S01_hloubka_zavitu,d2=(S01_prumer_vnitrni) ); |
| |
| translate([0,0,S01_vyska_spodniho_zavitu]) |
| cylinder (h = S01_sila_drzaku_RJ11-0.3, r=(S01_prumer_vnitrni)/2-S01_hloubka_zavitu/2+0.5, $fn=100); |
| |
| translate([-senzor_delka/2,senzor_sirka/2,0]) |
| { |
| cylinder (h = vyska_hlavy_sroubu, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu]) |
| cylinder(h=2+0.02, r1=(prumer_hlavy_sroubu)/2, r2=(prumer_sroubu+0.2)/2); |
| } |
| |
| translate([senzor_delka/2,-senzor_sirka/2,0]) |
| { |
| cylinder (h = vyska_hlavy_sroubu, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu]) |
| cylinder(h=2+0.02, r1=(prumer_hlavy_sroubu)/2, r2=(prumer_sroubu+0.2)/2); |
| } |
| |
| translate([senzor_delka/2,senzor_sirka/2,0]) |
| { |
| cylinder (h = vyska_hlavy_sroubu, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu]) |
| cylinder(h=2+0.02, r1=(prumer_hlavy_sroubu)/2, r2=(prumer_sroubu+0.2)/2); |
| } |
| } |
| |
| //spodní závit |
| translate([0,0,-5]) |
| screw_thread((S01_prumer_vnitrni),S01_hloubka_zavitu,55,S01_vyska_spodniho_zavitu+5+0.01,PI/2,2); |
| difference() |
| { |
| union() |
| { |
| //uchyty na modul |
| //sloupek 1 |
| translate([-senzor_delka/2,-senzor_sirka/2,0]) |
| SLOUPEK(); |
| |
| //otvor skrz |
| translate([0,0,S01_vyska_spodniho_zavitu+3*S01_sila_drzaku_RJ11-0.3]) |
| cylinder (h = S01_vyska-S01_vyska_horni_zavit-(S01_vyska_spodniho_zavitu+3*S01_sila_drzaku_RJ11-0.3), r=(S01_prumer_vnitrni)/2, $fn=100); |
| translate([senzor_delka/2,-senzor_sirka/2,0]) |
| SLOUPEK(); |
| |
| } |
| } |
| translate([senzor_delka/2,senzor_sirka/2,0]) |
| SLOUPEK(); |
| |
| translate([-senzor_delka/2,senzor_sirka/2,0]) |
| SLOUPEK(); |
| } |
| |
| translate([0,0,0]) |
| cylinder (h = R01_vyska_preryti_statoru+2*lozisko_vyska+S01_sila_materialu, r=(lozisko_prumer_vnejsi+0.2)/2, $fn=100); |
| |
| //doraz loziska |
| translate([0,0,(R01_vyska_preryti_statoru+2*lozisko_vyska)+S01_sila_materialu+8/2]) |
| cylinder(h=8, r1=(lozisko_prumer_vnejsi+0.2)/2, r2=0, center=true); |
| |
| } |
| } |
| } |
| |
| |
| //sloupek na senzor |
| module SLOUPEK() |
| { |
| translate([0,0,S01_sila_materialu]) |
| difference () |
| { |
| |
| cylinder (h = R01_vyska_preryti_statoru+2*lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky, r= sirka_matky/2+S01_sila_materialu, $fn=20); |
| |
| translate([0,0,R01_vyska_preryti_statoru+2*lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky-vyska_matky]) |
| cylinder (h = vyska_matky+0.01, r= (sirka_matky+0.2)/2, $fn=6); |
| |
| translate([0,0,-0.01]) |
| cylinder (h = R01_vyska_preryti_statoru+2*lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky+0.01, r= (prumer_sroubu+0.2)/2, $fn=40); |
| |
| translate([0,0,-0.01]) |
| cylinder (h = vyska_hlavy_sroubu-S01_sila_materialu, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| |
| translate([0,0,vyska_hlavy_sroubu-S01_sila_materialu-0.02]) |
| cylinder(h=2+0.02, r1=(prumer_hlavy_sroubu)/2, r2=(prumer_sroubu+0.2)/2); |
| |
| } |
| } |
| |
| |
| |
| WINDGAUGE02A_S01(); |
| |
| |
| |