| 73,29 → 73,29 |
|---|
| //otvory na hlavy sroubu v uchytu loziska |
| translate([-senzor_delka/2,-senzor_sirka/2,0]) |
| { |
| cylinder (h = vyska_hlavy_sroubu, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu]) |
| cylinder (h = vyska_hlavy_sroubu+10, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu+10]) |
| cylinder(h=2+0.02, r1=(prumer_hlavy_sroubu)/2, r2=(prumer_sroubu+0.2)/2); |
| } |
| |
| translate([-senzor_delka/2,senzor_sirka/2,0]) |
| { |
| cylinder (h = vyska_hlavy_sroubu, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu]) |
| cylinder (h = vyska_hlavy_sroubu+10, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu+10]) |
| cylinder(h=2+0.02, r1=(prumer_hlavy_sroubu)/2, r2=(prumer_sroubu+0.2)/2); |
| } |
| |
| translate([senzor_delka/2,-senzor_sirka/2,0]) |
| { |
| cylinder (h = vyska_hlavy_sroubu, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu]) |
| cylinder (h = vyska_hlavy_sroubu+10, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu+10]) |
| cylinder(h=2+0.02, r1=(prumer_hlavy_sroubu)/2, r2=(prumer_sroubu+0.2)/2); |
| } |
| |
| translate([senzor_delka/2,senzor_sirka/2,0]) |
| { |
| cylinder (h = vyska_hlavy_sroubu, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu]) |
| cylinder (h = vyska_hlavy_sroubu+10, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| translate([0,0,vyska_hlavy_sroubu+10]) |
| cylinder(h=2+0.02, r1=(prumer_hlavy_sroubu)/2, r2=(prumer_sroubu+0.2)/2); |
| } |
| } |
| 147,9 → 147,9 |
|---|
| cylinder (h = R01_vyska_preryti_statoru+2*lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky+0.01, r= (prumer_sroubu+0.2)/2, $fn=40); |
| |
| translate([0,0,-0.01]) |
| cylinder (h = vyska_hlavy_sroubu-S01_sila_materialu, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| cylinder (h = vyska_hlavy_sroubu+10-S01_sila_materialu, r= (prumer_hlavy_sroubu)/2, $fn=40); |
| |
| translate([0,0,vyska_hlavy_sroubu-S01_sila_materialu-0.02]) |
| translate([0,0,vyska_hlavy_sroubu+10-S01_sila_materialu-0.02]) |
| cylinder(h=2+0.02, r1=(prumer_hlavy_sroubu)/2, r2=(prumer_sroubu+0.2)/2); |
| |
| } |