| 64,11 → 64,11 |
|---|
| //otvor na ložisko |
| difference() |
| { |
| translate([0,0,(R01_vyska_preryti_statoru+2*lozisko_vyska)/2+S01_sila_materialu]) |
| cylinder (h = R01_vyska_preryti_statoru+2*lozisko_vyska, r=(lozisko_prumer_vnejsi+2*S01_sila_materialu)/2, center = true, $fn=100); |
| translate([0,0,(R01_vyska_preryti_statoru+lozisko_vyska)/2+S01_sila_materialu]) |
| cylinder (h = R01_vyska_preryti_statoru+lozisko_vyska, r=(lozisko_prumer_vnejsi+2*S01_sila_materialu)/2, center = true, $fn=100); |
| |
| translate([0,0,(R01_vyska_preryti_statoru+2*lozisko_vyska)/2+S01_sila_materialu]) |
| cylinder (h = R01_vyska_preryti_statoru+2*lozisko_vyska+0.01, r=(lozisko_prumer_vnejsi+0.2)/2, center = true, $fn=100); |
| translate([0,0,(R01_vyska_preryti_statoru+lozisko_vyska)/2+S01_sila_materialu]) |
| cylinder (h = R01_vyska_preryti_statoru+lozisko_vyska+0.01, r=(lozisko_prumer_vnejsi+0.2)/2, center = true, $fn=100); |
| |
| //otvory na hlavy sroubu v uchytu loziska |
| translate([-senzor_delka/2,-senzor_sirka/2,0]) |
| 120,10 → 120,10 |
|---|
| } |
| |
| translate([0,0,0]) |
| cylinder (h = R01_vyska_preryti_statoru+2*lozisko_vyska+S01_sila_materialu, r=(lozisko_prumer_vnejsi+0.2)/2, $fn=100); |
| cylinder (h = R01_vyska_preryti_statoru+lozisko_vyska+S01_sila_materialu, r=(lozisko_prumer_vnejsi+0.2)/2, $fn=100); |
| |
| //doraz loziska |
| translate([0,0,(R01_vyska_preryti_statoru+2*lozisko_vyska)+S01_sila_materialu+8/2]) |
| translate([0,0,(R01_vyska_preryti_statoru+lozisko_vyska)+S01_sila_materialu+8/2]) |
| cylinder(h=8, r1=(lozisko_prumer_vnejsi+0.2)/2, r2=0, center=true); |
| |
| } |
| 138,9 → 138,9 |
|---|
| difference () |
| { |
| |
| cylinder (h = R01_vyska_preryti_statoru+2*lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky, r= sirka_matky/2+S01_sila_materialu, $fn=20); |
| cylinder (h = R01_vyska_preryti_statoru+lozisko_vyska+magnet_vyska+R03_vyska_narezeni_hridelky+2*S01_sila_materialu, r= sirka_matky/2+S01_sila_materialu, $fn=20); |
| |
| translate([0,0,R01_vyska_preryti_statoru+2*lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky-vyska_matky]) |
| translate([0,0,R01_vyska_preryti_statoru+lozisko_vyska+magnet_vyska+R03_vyska_narezeni_hridelky+2*S01_sila_materialu-vyska_matky]) |
| cylinder (h = vyska_matky+0.01, r= (sirka_matky+0.2)/2, $fn=6); |
| |
| translate([0,0,-0.01]) |