| 38,20 → 38,20 |
|---|
| cylinder (h = S01_sila_materialu+0.01, r=(lozisko_prumer_vnitrni+0.2)/2+lozisko_prekryv, center = true, $fn=100); |
| |
| //otvor na šroub 1 |
| translate([-senzor_delka/2,-senzor_sirka/2,S01_vyska_komponentu_na_lozisko/2]) |
| cylinder (h = S01_vyska_komponentu_na_lozisko+0.01, r=(prumer_sroubu)/2, center = true, $fn=100); |
| translate([-senzor_delka/2,-senzor_sirka/2,(lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky)/2]) |
| cylinder (h = lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky+0.01, r=(prumer_sroubu)/2, center = true, $fn=100); |
| |
| //otvor na šroub 2 |
| translate([senzor_delka/2,-senzor_sirka/2,S01_vyska_komponentu_na_lozisko/2]) |
| cylinder (h = S01_vyska_komponentu_na_lozisko+0.01, r=(prumer_sroubu)/2, center = true, $fn=100); |
| translate([senzor_delka/2,-senzor_sirka/2,(lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky)/2]) |
| cylinder (h = lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky+0.01, r=(prumer_sroubu)/2, center = true, $fn=100); |
| |
| //otvor na šroub 3 |
| translate([senzor_delka/2,senzor_sirka/2,S01_vyska_komponentu_na_lozisko/2]) |
| cylinder (h = S01_vyska_komponentu_na_lozisko+0.01, r=(prumer_sroubu)/2, center = true, $fn=100); |
| translate([senzor_delka/2,senzor_sirka/2,(lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky)/2]) |
| cylinder (h = lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky+0.01, r=(prumer_sroubu)/2, center = true, $fn=100); |
| |
| //otvor na šroub 4 |
| translate([-senzor_delka/2,senzor_sirka/2,S01_vyska_komponentu_na_lozisko/2]) |
| cylinder (h = S01_vyska_komponentu_na_lozisko+0.01, r=(prumer_sroubu)/2, center = true, $fn=100); |
| translate([-senzor_delka/2,senzor_sirka/2,(lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky)/2]) |
| cylinder (h = lozisko_vyska+2*S01_sila_materialu+2*S01_sila_materialu+vyska_hlavy_sroubu+magnet_vyska+vyska_matky+0.01, r=(prumer_sroubu)/2, center = true, $fn=100); |
| |
| } |
| translate([0,0,lozisko_vyska/2+S01_sila_materialu]) |