| 3,118 → 3,27 |
|---|
| |
| include <polyScrewThread_r1.scad> |
| |
| //Držák na konektor RJ11 |
| |
| PI=3.141592; |
| module WINDGAUGE02A_S03() |
| { |
| difference() |
| difference() |
| { |
| //valec se zavitem |
| union() { |
| |
| |
| difference() |
| { |
| |
| |
| cylinder (h = S01_sila_materialu, r=(S01_prumer_vnitrni)/2-3, $fn=100); |
| |
| translate([0,0,0]) |
| cylinder (h = S01_sila_drzaku_RJ11, r=(S01_prumer_vnitrni)/2-S01_hloubka_zavitu/2+0.5, $fn=100); |
| |
| //otvor na pruchod hridelky |
| translate([0,0,S01_sila_materialu/2]) |
| cylinder (h = S01_sila_materialu+0.01, r=(lozisko_prumer_vnitrni+0.2)/2+lozisko_prekryv, center = true, $fn=100); |
| |
| //otvor na šroub 1 |
| translate([-senzor_delka/2,-senzor_sirka/2,0]) |
| cylinder (h = S01_sila_materialu+0.01, r=(prumer_sroubu)/2, $fn=100); |
| |
| //otvor na šroub 2 |
| translate([senzor_delka/2,-senzor_sirka/2,0]) |
| cylinder (h = S01_sila_materialu+0.01, r=(prumer_sroubu)/2, $fn=100); |
| |
| //otvor na šroub 3 |
| translate([senzor_delka/2,senzor_sirka/2,0]) |
| cylinder (h = S01_sila_materialu+0.01, r=(prumer_sroubu)/2, $fn=100); |
| translate([0,0,S01_sila_drzaku_RJ11/2]) |
| cube([S01_hrana_A_RJ11,S01_hrana_B_RJ11,S01_sila_drzaku_RJ11+0.01],center=true); |
| |
| //otvor na šroub 4 |
| translate([-senzor_delka/2,senzor_sirka/2,0]) |
| cylinder (h = S01_sila_materialu+0.01, r=(prumer_sroubu)/2, $fn=100); |
| |
| } |
| translate([0,0,lozisko_vyska/2+S01_sila_materialu]) |
| difference() |
| { |
| |
| cylinder (h = lozisko_vyska, r=(lozisko_prumer_vnejsi+2*S01_sila_materialu)/2, center = true, $fn=100); |
| cylinder (h = lozisko_vyska+0.01, r=(lozisko_prumer_vnejsi+0.2)/2, center = true, $fn=100); |
| |
| |
| } |
| //otvor až ke kraji |
| translate([0,((S01_prumer_vnitrni)/2-S01_hloubka_zavitu/2+0.5)/2,S01_sila_drzaku_RJ11/2]) cube([S01_hrana_A_RJ11,(S01_prumer_vnitrni)/2-S01_hloubka_zavitu/2+0.5,S01_sila_drzaku_RJ11+0.01],center=true); |
| } |
| |
| } |
| |
| |
| |
| } |
| //otvor na šroub 1 |
| translate([-senzor_delka/2,-senzor_sirka/2,S01_sila_materialu]) |
| cylinder (h = lozisko_vyska+0.01, r=(prumer_hlavy_sroubu)/2, $fn=100); |
| |
| //otvor na šroub 2 |
| translate([senzor_delka/2,-senzor_sirka/2,S01_sila_materialu]) |
| cylinder (h = lozisko_vyska+0.01, r=(prumer_hlavy_sroubu)/2, $fn=100); |
| |
| //otvor na šroub 3 |
| translate([senzor_delka/2,senzor_sirka/2,S01_sila_materialu]) |
| cylinder (h = lozisko_vyska+0.01, r=(prumer_hlavy_sroubu)/2, $fn=100); |
| |
| //otvor na šroub 4 |
| translate([-senzor_delka/2,senzor_sirka/2,S01_sila_materialu]) |
| cylinder (h = lozisko_vyska+0.01, r=(prumer_hlavy_sroubu)/2, $fn=100); |
| } |
| |
| } |
| |
| |
| |
| |
| WINDGAUGE02A_S03(); |
| |
| |
| /* |
| module WINDGAUGE02A_S03(S01_sila_materialu,S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,lozisko_vyska,lozisko_prumer_vnejsi,lozisko_prumer_vnitrni,lozisko_prekryv,vyska_matky,prumer_orechu,prumer_sroubu,vyska_hlavy_sroubu,prumer_hlavy_sroubu,S01_tolerance_zavit,R02_vzdalenost_mezi_uchyty_lopatek,L01_sila_zapusteni_drzaku,L01_hloubka_zapusteni,vule_mezi_statorem_rotorem,S01_sila_materialu,S01_hloubka_zavitu) |
| { |
| union() |
| { |
| //valec se zavitem |
| difference() |
| { |
| |
| screw_thread((R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem)-S01_tolerance_zavit,S01_hloubka_zavitu,55,S01_vyska_komponentu_na_lozisko,PI/2,2); |
| |
| translate([0,0,S01_sila_materialu+S01_vyska_komponentu_na_lozisko/2]) |
| cylinder (h = S01_vyska_komponentu_na_lozisko+0.01, r=((R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem)-S01_tolerance_zavit/2)/2-S01_hloubka_zavitu/2-S01_sila_materialu, center = true, $fn=100); |
| |
| //otvor na pruchod hridelky |
| translate([0,0,S01_sila_materialu/2]) |
| cylinder (h = S01_sila_materialu+0.01, r=(lozisko_prumer_vnitrni+2*lozisko_prekryv+0.2)/2, center = true, $fn=100); |
| } |
| |
| //otvory na ložisko |
| translate([0,0,lozisko_vyska/2+S01_sila_materialu]) |
| difference() |
| { |
| cylinder (h = lozisko_vyska, r=(lozisko_prumer_vnejsi+2*S01_sila_materialu)/2, center = true, $fn=100); |
| cylinder (h = lozisko_vyska+0.01, r=(lozisko_prumer_vnejsi+0.2)/2, center = true, $fn=100); |
| |
| |
| } |
| |
| } |
| } |
| |
| |
| |
| |
| |
| WINDGAUGE02A_S03(S01_sila_materialu,S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,lozisko_vyska,lozisko_prumer_vnejsi,lozisko_prumer_vnitrni,lozisko_prekryv,vyska_matky,prumer_orechu,prumer_sroubu,vyska_hlavy_sroubu,prumer_hlavy_sroubu,S01_tolerance_zavit,R02_vzdalenost_mezi_uchyty_lopatek,L01_sila_zapusteni_drzaku,L01_hloubka_zapusteni,vule_mezi_statorem_rotorem,S01_sila_materialu,S01_hloubka_zavitu); |
| |
| */ |