| 0,0 → 1,171 |
|---|
| CCS PCH C Compiler, Version 4.106, 47914 27-12-10 13:42 |
| |
| Filename: C:\Users\kakl\Documents\MLAB\Modules\PIC\PIC18F8xTQ8001A\SW\PIC18F8310\blik.lst |
| |
| ROM used: 188 bytes (2%) |
| Largest free fragment is 8004 |
| RAM used: 5 (1%) at main() level |
| 6 (1%) worst case |
| Stack: 1 locations |
| |
| * |
| 0000: GOTO 002C |
| .................... #include "C:\Users\kakl\Documents\MLAB\Modules\PIC\PIC18F8xTQ8001A\SW\PIC18F8310\blik.h" |
| .................... #include <18F8310.h> |
| .................... //////// Standard Header file for the PIC18F8310 device //////////////// |
| .................... #device PIC18F8310 |
| .................... #list |
| .................... |
| .................... #device adc=8 |
| .................... |
| .................... #FUSES NOWDT //No Watch Dog Timer |
| .................... #FUSES WDT128 //Watch Dog Timer uses 1:128 Postscale |
| .................... #FUSES INTRC_IO //Internal RC Osc, no CLKOUT |
| .................... #FUSES NOBROWNOUT //No brownout reset |
| .................... #FUSES BORV21 //Brownout reset at 2.1V |
| .................... #FUSES NOPUT //No Power Up Timer |
| .................... #FUSES BW16 //16-bit external bus mode |
| .................... #FUSES STVREN //Stack full/underflow will cause reset |
| .................... #FUSES NODEBUG //No Debug mode for ICD |
| .................... #FUSES IESO //Internal External Switch Over mode enabled |
| .................... #FUSES NOFCMEN //Fail-safe clock monitor disabled |
| .................... #FUSES NOXINST //Extended set extension and Indexed Addressing mode disabled (Legacy mode) |
| .................... #FUSES NOWAIT //Wait selections unavailable for Table Reads or Table Writes |
| .................... #FUSES NOPROTECT //Code not protected from reading |
| .................... #FUSES NOEBTR //Memory not protected from table reads |
| .................... #FUSES LPT1OSC //Timer1 configured for low-power operation |
| .................... #FUSES MCLR //Master Clear pin enabled |
| .................... #FUSES MCU //Microcontroller Mode |
| .................... |
| .................... #use delay(clock=4000000) |
| 0004: CLRF FEA |
| 0006: MOVLW 06 |
| 0008: MOVWF FE9 |
| 000A: MOVF FEF,W |
| 000C: BZ 002A |
| 000E: MOVLW 01 |
| 0010: MOVWF 01 |
| 0012: CLRF 00 |
| 0014: DECFSZ 00,F |
| 0016: BRA 0014 |
| 0018: DECFSZ 01,F |
| 001A: BRA 0012 |
| 001C: MOVLW 4A |
| 001E: MOVWF 00 |
| 0020: DECFSZ 00,F |
| 0022: BRA 0020 |
| 0024: BRA 0026 |
| 0026: DECFSZ FEF,F |
| 0028: BRA 000E |
| 002A: RETLW 00 |
| .................... |
| .................... |
| .................... |
| .................... |
| .................... #define LED PIN_J6 //CHANGE PIN_XX TO YOUR LED PIN NUMBER, EX: PIN_A5 |
| .................... |
| .................... void main() |
| .................... { |
| 002C: CLRF FF8 |
| 002E: BCF FD0.7 |
| 0030: CLRF FEA |
| 0032: CLRF FE9 |
| 0034: MOVLW 60 |
| 0036: MOVWF FD3 |
| 0038: MOVF FD3,W |
| 003A: MOVF FC1,W |
| 003C: ANDLW C0 |
| 003E: IORLW 0F |
| 0040: MOVWF FC1 |
| 0042: MOVLW 07 |
| 0044: MOVWF FB4 |
| .................... |
| .................... setup_adc_ports(NO_ANALOGS|VSS_VDD); |
| 0046: MOVF FC1,W |
| 0048: ANDLW C0 |
| 004A: IORLW 0F |
| 004C: MOVWF FC1 |
| .................... setup_adc(ADC_CLOCK_DIV_2); |
| 004E: BCF FC0.0 |
| 0050: BCF FC0.1 |
| 0052: BCF FC0.2 |
| 0054: BCF FC0.7 |
| 0056: BSF FC2.0 |
| .................... setup_psp(PSP_DISABLED); |
| 0058: BCF FB0.4 |
| .................... setup_spi(SPI_SS_DISABLED); |
| 005A: BCF FC6.5 |
| 005C: BCF F94.5 |
| 005E: BSF F94.4 |
| 0060: BCF F94.3 |
| 0062: MOVLW 01 |
| 0064: MOVWF FC6 |
| 0066: MOVLW 00 |
| 0068: MOVWF FC7 |
| .................... setup_wdt(WDT_OFF); |
| 006A: BCF FD1.0 |
| .................... setup_timer_0(RTCC_INTERNAL); |
| 006C: MOVLW 80 |
| 006E: MOVWF FD5 |
| .................... setup_timer_1(T1_DISABLED); |
| 0070: CLRF FCD |
| .................... setup_timer_2(T2_DISABLED,0,1); |
| 0072: MOVLW 00 |
| 0074: MOVWF FCA |
| 0076: MOVLW 00 |
| 0078: MOVWF FCB |
| .................... setup_ccp1(CCP_OFF); |
| 007A: BSF F94.2 |
| 007C: CLRF FBD |
| .................... setup_comparator(NC_NC_NC_NC); |
| 007E: MOVLW 07 |
| 0080: MOVWF FB4 |
| 0082: MOVF F97,W |
| 0084: MOVWF F97 |
| 0086: MOVLW 03 |
| 0088: MOVWF 00 |
| 008A: DECFSZ 00,F |
| 008C: BRA 008A |
| 008E: MOVF FB4,W |
| 0090: BCF FA1.6 |
| .................... setup_vref(FALSE); |
| 0092: CLRF FB5 |
| .................... |
| .................... //Example blinking LED program |
| .................... while(true){ |
| .................... output_low(LED); |
| 0094: BCF F9A.6 |
| 0096: BCF F91.6 |
| .................... delay_ms(1000); |
| 0098: MOVLW 04 |
| 009A: MOVWF 05 |
| 009C: MOVLW FA |
| 009E: MOVWF 06 |
| 00A0: RCALL 0004 |
| 00A2: DECFSZ 05,F |
| 00A4: BRA 009C |
| .................... output_high(LED); |
| 00A6: BCF F9A.6 |
| 00A8: BSF F91.6 |
| .................... delay_ms(1000); |
| 00AA: MOVLW 04 |
| 00AC: MOVWF 05 |
| 00AE: MOVLW FA |
| 00B0: MOVWF 06 |
| 00B2: RCALL 0004 |
| 00B4: DECFSZ 05,F |
| 00B6: BRA 00AE |
| .................... } |
| 00B8: BRA 0094 |
| .................... |
| .................... } |
| 00BA: SLEEP |
| |
| Configuration Fuses: |
| Word 1: 8800 INTRC_IO IESO NOFCMEN |
| Word 2: 0E19 NOBROWNOUT WDT128 NOWDT BORV21 NOPUT |
| Word 3: 85C3 BW16 CCP2C1 NOWAIT LPT1OSC MCLR MCU |
| Word 4: 0081 STVREN NODEBUG NOXINST NOXINST |
| Word 5: 0001 NOPROTECT |
| Word 6: 0000 |
| Word 7: 0001 NOEBTR |