Problem with comparison.
/Modules/PowerSW/SCH/POWER_SW.BOM
0,0 → 1,35
4x Power Switch Revised: Tuesday, December 12, 2006
PowerSW Revision: 1
 
 
 
 
 
 
 
Bill Of Materials December 12,2006 0:55:24 Page1
 
Quantity Reference Part PCB Footprint
______________________________________________
 
5 D1 1N5818 DO41
D2 1N5818 DO41
D3 1N5818 DO41
D4 1N5818 DO41
D5 1N5818 DO41
1 J1 JUMP2X1 JUMP2X1
1 J2 JUMP2X4 JUMP2X4
4 J3 ARK210/2 ARK210/2
J4 ARK210/2 ARK210/2
J5 ARK210/2 ARK210/2
J6 ARK210/2 ARK210/2
4 M1 HOLE_M3 HOLE_M3
M2 HOLE_M3 HOLE_M3
M3 HOLE_M3 HOLE_M3
M4 HOLE_M3 HOLE_M3
2 Q1 SO8_2xNFET_9926 SO8_2FET
Q2 SO8_2xNFET_9926 SO8_2FET
4 R1 47 R0805
R2 47 R0805
R3 47 R0805
R4 47 R0805
/Modules/PowerSW/SCH/POWER_SW.DSN
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/Modules/PowerSW/SCH/power_sw.asc
0,0 → 1,55
*PADS-PCB*
*PART*
D1 D,1N5818@DO41
D2 D,1N5818@DO41
D3 D,1N5818@DO41
D4 D,1N5818@DO41
D5 D,1N5818@DO41
J1 JUMP2X1,JUMP2X1@JUMP2X1
J2 JUMP2X4,JUMP2X4@JUMP2X4
J3 SCW2,ARK210/2@ARK210/2
J4 SCW2,ARK210/2@ARK210/2
J5 SCW2,ARK210/2@ARK210/2
J6 SCW2,ARK210/2@ARK210/2
M1 PAD,HOLE_M3@HOLE_M3
M2 PAD,HOLE_M3@HOLE_M3
M3 PAD,HOLE_M3@HOLE_M3
M4 PAD,HOLE_M3@HOLE_M3
Q1 SO8_2FET,SO8_2xNFET_9926@SO8_2FET
Q2 SO8_2FET,SO8_2xNFET_9926@SO8_2FET
R1 R,100@R0805
R2 R,100@R0805
R3 R,100@R0805
R4 R,100@R0805
 
*NET*
*SIGNAL* N77576
R3.2 Q2.G1
*SIGNAL* N77605
R4.2 Q2.G2
*SIGNAL* N78132
R4.1 J2.3 J2.4
*SIGNAL* N77715
D3.A J4.2 Q2.D1
*SIGNAL* N77744
D4.A J4.1 Q2.D2
*SIGNAL* VDD
D1.C D2.C D3.C D4.C J5.2 J5.1 J6.1 D5.C
*SIGNAL* N76250
R1.2 Q1.G1
*SIGNAL* GND
M3.1 M4.1 M1.1 M2.1 Q1.S1 J1.1 J1.2 Q1.S2
Q2.S1 Q2.S2 J6.2 D5.A
*SIGNAL* N77186
R2.2 Q1.G2
*SIGNAL* N76675
D1.A J3.2 Q1.D1
*SIGNAL* N77773
J3.1 D2.A Q1.D2
*SIGNAL* N78113
R3.1 J2.1 J2.2
*SIGNAL* N80435
J2.5 J2.6 R1.1
*SIGNAL* N77327
J2.7 J2.8 R2.1
*END*