| 0,0 → 1,131 |
|---|
| # generated by Slic3r 1.2.8-dev on Fri Jun 5 14:59:35 2015 |
| avoid_crossing_perimeters = 0 |
| bed_shape = 0x0,180x0,180x180,0x180 |
| bed_temperature = 50 |
| before_layer_gcode = |
| bottom_solid_layers = 3 |
| bridge_acceleration = 1000 |
| bridge_fan_speed = 100 |
| bridge_flow_ratio = 1 |
| bridge_speed = 5 |
| brim_width = 0 |
| complete_objects = 0 |
| cooling = 1 |
| default_acceleration = 500 |
| disable_fan_first_layers = 1 |
| dont_support_bridges = 1 |
| duplicate_distance = 6 |
| end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n |
| external_fill_pattern = rectilinear |
| external_perimeter_extrusion_width = 0 |
| external_perimeter_speed = 90% |
| external_perimeters_first = 0 |
| extra_perimeters = 1 |
| extruder_clearance_height = 20 |
| extruder_clearance_radius = 20 |
| extruder_offset = 0x0 |
| extrusion_axis = E |
| extrusion_multiplier = 1 |
| extrusion_width = 0 |
| fan_always_on = 1 |
| fan_below_layer_time = 60 |
| filament_colour = #FFFFFF |
| filament_diameter = 1.75 |
| fill_angle = 45 |
| fill_density = 10% |
| fill_pattern = rectilinear |
| first_layer_acceleration = 500 |
| first_layer_bed_temperature = 60 |
| first_layer_extrusion_width = 180% |
| first_layer_height = 0.3 |
| first_layer_speed = 60% |
| first_layer_temperature = 212 |
| gap_fill_speed = 10 |
| gcode_arcs = 0 |
| gcode_comments = 0 |
| gcode_flavor = reprap |
| infill_acceleration = 500 |
| infill_every_layers = 1 |
| infill_extruder = 1 |
| infill_extrusion_width = 0 |
| infill_first = 0 |
| infill_only_where_needed = 0 |
| infill_overlap = 15% |
| infill_speed = 60 |
| interface_shells = 0 |
| layer_gcode = |
| layer_height = 0.3 |
| max_fan_speed = 100 |
| max_print_speed = 80 |
| max_volumetric_speed = 0 |
| min_fan_speed = 100 |
| min_print_speed = 10 |
| min_skirt_length = 0 |
| notes = |
| nozzle_diameter = 0.4 |
| octoprint_apikey = 330CC1C393FC4CD08C420E476D472A7E |
| octoprint_host = 192.168.1.25 |
| only_retract_when_crossing_perimeters = 1 |
| ooze_prevention = 0 |
| output_filename_format = [input_filename_base].gcode |
| overhangs = 1 |
| perimeter_acceleration = 500 |
| perimeter_extruder = 1 |
| perimeter_extrusion_width = 0 |
| perimeter_speed = 45 |
| perimeters = 1 |
| post_process = |
| pressure_advance = 0 |
| raft_layers = 0 |
| resolution = 0 |
| retract_before_travel = 2 |
| retract_layer_change = 1 |
| retract_length = 1.3 |
| retract_length_toolchange = 3 |
| retract_lift = 0 |
| retract_restart_extra = 0 |
| retract_restart_extra_toolchange = 0 |
| retract_speed = 60 |
| seam_position = aligned |
| skirt_distance = 10 |
| skirt_height = 1 |
| skirts = 1 |
| slowdown_below_layer_time = 30 |
| small_perimeter_speed = 10 |
| solid_infill_below_area = 70 |
| solid_infill_every_layers = 0 |
| solid_infill_extruder = 1 |
| solid_infill_extrusion_width = 0 |
| solid_infill_speed = 55 |
| spiral_vase = 0 |
| standby_temperature_delta = -5 |
| start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder |
| support_material = 0 |
| support_material_angle = 0 |
| support_material_contact_distance = 0.2 |
| support_material_enforce_layers = 0 |
| support_material_extruder = 1 |
| support_material_extrusion_width = 0 |
| support_material_interface_extruder = 1 |
| support_material_interface_layers = 0 |
| support_material_interface_spacing = 0 |
| support_material_interface_speed = 100% |
| support_material_pattern = rectilinear |
| support_material_spacing = 2.5 |
| support_material_speed = 60 |
| support_material_threshold = 0 |
| temperature = 212 |
| thin_walls = 1 |
| threads = 4 |
| toolchange_gcode = |
| top_infill_extrusion_width = 0 |
| top_solid_infill_speed = 50 |
| top_solid_layers = 3 |
| travel_speed = 130 |
| use_firmware_retraction = 0 |
| use_relative_e_distances = 1 |
| use_volumetric_e = 0 |
| vibration_limit = 0 |
| wipe = 1 |
| xy_size_compensation = 0 |
| z_offset = 0 |