/Modules/PowerSupply/LION1CELL01B/SW/PIC16F887/setting/LED_BAT7/main.bak |
---|
0,0 → 1,153 |
#include "main.h" |
#define EEPROM_SDA PIN_B0 |
#define EEPROM_SCL PIN_B1 |
#use i2c(master, sda=EEPROM_SDA, scl=EEPROM_SCL) |
#use rs232(baud=9600,parity=N,xmit=PIN_B3,rcv=PIN_B2,bits=8) //rcv TXD xmit RXD |
void main() |
{ |
setup_adc_ports(NO_ANALOGS|VSS_VDD); |
setup_adc(ADC_CLOCK_DIV_2); |
setup_spi(SPI_SS_DISABLED); |
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
setup_timer_1(T1_DISABLED); |
setup_timer_2(T2_DISABLED,0,1); |
setup_ccp1(CCP_OFF); |
setup_comparator(NC_NC_NC_NC);// This device COMP currently not supported by the PICWizard |
printf("Simple Thermomether \r\n",); |
unsigned int8 STAV1,STAV2; |
unsigned int16 SOUCET, SOUCET1; |
unsigned int8 LSB=0,ZK,k=0; |
//unsigned int8 |
while(TRUE) |
{ |
i2c_start(); //blockdatacontrol |
I2C_Write(0xAA); |
I2C_write(0x61); |
i2c_start(); |
I2C_Write(0xAA); |
i2c_write(0x00); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//dataflashclass |
I2C_Write(0xAA); |
I2C_write(0x3e); |
i2c_start(); |
I2C_Write(0xAA); |
i2c_write(0x40); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//dataflashblock |
I2C_Write(0xAA); |
I2C_write(0x3f); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x00); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x44); |
i2c_start(); |
I2C_Write(0xAB); |
ZK=I2C_read(0); |
i2c_stop(); |
delay_ms (1); |
printf("LED %lX \r\n", ZK); |
if(ZK==0x73) |
{ |
LSB=LSB-1; |
printf("Vysledne LSB %lX \r\n", LSB); |
while(TRUE) |
{ |
} |
} |
else |
{ |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x44); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x73); //pro 5LED 0x53 pro 7led 0x73 |
i2c_stop(); |
int i=64; |
SOUCET=0; |
SOUCET1=0; |
/* |
for (i=64;i<96;++i) |
{ |
printf("%u\r\n",i); |
i2c_stop(); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(i); |
i2c_start(); |
I2C_Write(0xAB); |
STAV1=I2C_read(0); |
i2c_stop(); |
printf("STAV %lX \r\n", STAV1); |
SOUCET=SOUCET+STAV1; |
} |
printf("SOUCET: %lX (procenta)\r\n", SOUCET); |
SOUCET1=SOUCET; |
SOUCET1=SOUCET1>>8; |
printf("Deleno 256: %lX (procenta)\r\n", SOUCET1); |
SOUCET1=SOUCET-SOUCET1; |
printf("Soucet - soucet/256: %lX \r\n", SOUCET1); |
LSB=(unsigned int8)SOUCET1; |
printf("LSB: %lX\r\n", LSB); |
//printf("Stav: %X (procenta)\r\n", STAV2); |
*/ |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x60); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(LSB); |
i2c_stop(); |
} |
LSB=LSB+1; |
delay_ms (100); |
} |
} |
/Modules/PowerSupply/LION1CELL01B/SW/PIC16F887/setting/Min_V_cl/main.bak |
---|
0,0 → 1,154 |
#include "C:\Users\Honza\Documents\pic\I2C_bat_pam\Min_V_cl\main.h" |
#define EEPROM_SDA PIN_B0 |
#define EEPROM_SCL PIN_B1 |
#use i2c(master, sda=EEPROM_SDA, scl=EEPROM_SCL) |
#use rs232(baud=9600,parity=N,xmit=PIN_B3,rcv=PIN_B2,bits=8) //rcv TXD xmit RXD |
void main() |
{ |
setup_adc_ports(NO_ANALOGS|VSS_VDD); |
setup_adc(ADC_CLOCK_DIV_2); |
setup_spi(SPI_SS_DISABLED); |
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
setup_timer_1(T1_DISABLED); |
setup_timer_2(T2_DISABLED,0,1); |
setup_ccp1(CCP_OFF); |
setup_comparator(NC_NC_NC_NC);// This device COMP currently not supported by the PICWizard |
printf("Simple Thermomether \r\n",); |
unsigned int8 STAV1,STAV2; |
unsigned int16 SOUCET, SOUCET1; |
unsigned int8 LSB=0,ZK,k=0,VH,VL; |
//unsigned int8 |
while(TRUE) |
{ |
i2c_start(); //blockdatacontrol |
I2C_Write(0xAA); |
I2C_write(0x61); |
i2c_start(); |
I2C_Write(0xAA); |
i2c_write(0x00); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//dataflashclass |
I2C_Write(0xAA); |
I2C_write(0x3e); |
i2c_start(); |
I2C_Write(0xAA); |
i2c_write(0x50); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//dataflashblock |
I2C_Write(0xAA); |
I2C_write(0x3f); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x02); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//blockdata horni bit |
I2C_Write(0xAA); |
I2C_write(0x43); |
i2c_start(); |
I2C_Write(0xAB); |
VH=I2C_read(0); |
i2c_stop(); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x44); |
i2c_start(); |
I2C_Write(0xAB); |
VL=I2C_read(0); |
i2c_stop(); |
delay_ms (1); |
printf("VL %lX \r\n", VL); |
printf("LH %lX \r\n", VH); |
if(VH==0x0A) |
{ |
LSB=LSB-1; |
printf("Vysledne LSB %lX \r\n", LSB); |
while(TRUE) |
{ |
} |
} |
else |
{ |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x43); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x0A); |
i2c_stop(); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x44); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x5A); |
i2c_stop(); |
} |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x60); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(LSB); |
i2c_stop(); |
LSB=LSB+1; |
delay_ms (100); |
} |
} |
/Modules/PowerSupply/LION1CELL01B/SW/PIC16F887/setting/Q_MAX/main.bak |
---|
0,0 → 1,156 |
#include "C:\Users\Honza\Documents\pic\I2C_bat_pam\Q_MAX\main.h" |
#define EEPROM_SDA PIN_B0 |
#define EEPROM_SCL PIN_B1 |
#use i2c(master, sda=EEPROM_SDA, scl=EEPROM_SCL) |
#use rs232(baud=9600,parity=N,xmit=PIN_B3,rcv=PIN_B2,bits=8) //rcv TXD xmit RXD |
void main() |
{ |
setup_adc_ports(NO_ANALOGS|VSS_VDD); |
setup_adc(ADC_CLOCK_DIV_2); |
setup_spi(SPI_SS_DISABLED); |
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
setup_timer_1(T1_DISABLED); |
setup_timer_2(T2_DISABLED,0,1); |
setup_ccp1(CCP_OFF); |
setup_comparator(NC_NC_NC_NC);// This device COMP currently not supported by the PICWizard |
printf("Simple Thermomether \r\n",); |
unsigned int8 STAV1,STAV2; |
unsigned int16 SOUCET, SOUCET1; |
unsigned int8 LSB=0,ZK,k=0,VH,VL; |
//unsigned int8 |
while(TRUE) |
{ |
i2c_start(); //blockdatacontrol |
I2C_Write(0xAA); |
I2C_write(0x61); |
i2c_start(); |
I2C_Write(0xAA); |
i2c_write(0x00); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//dataflashclass |
I2C_Write(0xAA); |
I2C_write(0x3e); |
i2c_start(); |
I2C_Write(0xAA); |
i2c_write(0x52); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//dataflashblock |
I2C_Write(0xAA); |
I2C_write(0x3f); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x00); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x40); |
i2c_start(); |
I2C_Write(0xAB); |
VH=I2C_read(0); |
i2c_stop(); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x41); |
i2c_start(); |
I2C_Write(0xAB); |
VL=I2C_read(0); |
i2c_stop(); |
delay_ms (10); |
printf("VL %lX \r\n", VL); |
printf("LH %lX \r\n", VH); |
if(VL==0x48) |
{ |
LSB=LSB-1; |
printf("Vysledne LSB %lX \r\n", LSB); |
while(TRUE) |
{ |
} |
} |
else |
{ |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x40); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x0D); |
i2c_stop(); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x41); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x48); |
i2c_stop(); |
} |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x60); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(LSB); |
i2c_stop(); |
LSB=LSB+1; |
delay_ms (100); |
} |
} |
/Modules/PowerSupply/LION1CELL01B/SW/PIC16F887/setting/V_MAX/main.bak |
---|
0,0 → 1,153 |
#include "C:\Users\Honza\Documents\pic\I2C_bat_pam\V_MAX\main.h" |
#define EEPROM_SDA PIN_B0 |
#define EEPROM_SCL PIN_B1 |
#use i2c(master, sda=EEPROM_SDA, scl=EEPROM_SCL) |
#use rs232(baud=9600,parity=N,xmit=PIN_B3,rcv=PIN_B2,bits=8) //rcv TXD xmit RXD |
void main() |
{ |
setup_adc_ports(NO_ANALOGS|VSS_VDD); |
setup_adc(ADC_CLOCK_DIV_2); |
setup_spi(SPI_SS_DISABLED); |
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
setup_timer_1(T1_DISABLED); |
setup_timer_2(T2_DISABLED,0,1); |
setup_ccp1(CCP_OFF); |
setup_comparator(NC_NC_NC_NC);// This device COMP currently not supported by the PICWizard |
printf("Simple Thermomether \r\n",); |
unsigned int8 STAV1,STAV2; |
unsigned int16 SOUCET, SOUCET1; |
unsigned int8 LSB=0,ZK,k=0,VH,VL; |
//unsigned int8 |
while(TRUE) |
{ |
i2c_start(); //blockdatacontrol |
I2C_Write(0xAA); |
I2C_write(0x61); |
i2c_start(); |
I2C_Write(0xAA); |
i2c_write(0x00); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//dataflashclass |
I2C_Write(0xAA); |
I2C_write(0x3e); |
i2c_start(); |
I2C_Write(0xAA); |
i2c_write(0x52); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//dataflashblock |
I2C_Write(0xAA); |
I2C_write(0x3f); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x00); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x45); |
i2c_start(); |
I2C_Write(0xAB); |
VH=I2C_read(0); |
i2c_stop(); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x46); |
i2c_start(); |
I2C_Write(0xAB); |
VL=I2C_read(0); |
i2c_stop(); |
delay_ms (1); |
printf("VL %lX \r\n", VL); |
printf("LH %lX \r\n", VH); |
if(VL==0x10) |
{ |
LSB=LSB-1; |
printf("Vysledne LSB %lX \r\n", LSB); |
while(TRUE) |
{ |
} |
} |
else |
{ |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x45); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x68); |
i2c_stop(); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x46); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x10); |
i2c_stop(); |
} |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x60); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(LSB); |
i2c_stop(); |
LSB=LSB+1; |
delay_ms (100); |
} |
} |
/Modules/PowerSupply/LION1CELL01B/SW/PIC16F887/setting/LED_BAT/main.bak |
---|
0,0 → 1,152 |
//#include "C:\Users\Honza\Documents\pic\I2C_bat_pam\main.h" |
#define EEPROM_SDA PIN_B0 |
#define EEPROM_SCL PIN_B1 |
#use i2c(master, sda=EEPROM_SDA, scl=EEPROM_SCL) |
#use rs232(baud=9600,parity=N,xmit=PIN_B3,rcv=PIN_B2,bits=8) //rcv TXD xmit RXD |
#include "main.h" |
void main() |
{ |
setup_adc_ports(NO_ANALOGS|VSS_VDD); |
setup_adc(ADC_CLOCK_DIV_2); |
setup_spi(SPI_SS_DISABLED); |
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
setup_timer_1(T1_DISABLED); |
setup_timer_2(T2_DISABLED,0,1); |
setup_ccp1(CCP_OFF); |
setup_comparator(NC_NC_NC_NC);// This device COMP currently not supported by the PICWizard |
printf("Simple Thermomether \r\n",); |
unsigned int8 STAV1,STAV2; |
unsigned int16 SOUCET, SOUCET1; |
unsigned int8 LSB=0,ZK,k=0; |
//unsigned int8 |
while(TRUE) |
{ |
i2c_start(); //blockdatacontrol |
I2C_Write(0xAA); |
I2C_write(0x61); |
i2c_start(); |
I2C_Write(0xAA); |
i2c_write(0x00); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//dataflashclass |
I2C_Write(0xAA); |
I2C_write(0x3e); |
i2c_start(); |
I2C_Write(0xAA); |
i2c_write(0x40); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//dataflashblock |
I2C_Write(0xAA); |
I2C_write(0x3f); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x00); |
i2c_stop(); |
delay_ms (1); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x44); |
i2c_start(); |
I2C_Write(0xAB); |
ZK=I2C_read(0); |
i2c_stop(); |
delay_ms (1); |
printf("LED %lX \r\n", ZK); |
if(ZK==0x73) |
{ |
LSB=LSB-1; |
printf("Vysledne LSB %lX \r\n", LSB); |
while(TRUE) |
{ |
} |
} |
else |
{ |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x44); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(0x73); //pro 5LED 0x53 pro 7led 0x73 |
i2c_stop(); |
int i=64; |
SOUCET=0; |
SOUCET1=0; |
/* |
for (i=64;i<96;++i) |
{ |
printf("%u\r\n",i); |
i2c_stop(); |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(i); |
i2c_start(); |
I2C_Write(0xAB); |
STAV1=I2C_read(0); |
i2c_stop(); |
printf("STAV %lX \r\n", STAV1); |
SOUCET=SOUCET+STAV1; |
} |
printf("SOUCET: %lX (procenta)\r\n", SOUCET); |
SOUCET1=SOUCET; |
SOUCET1=SOUCET1>>8; |
printf("Deleno 256: %lX (procenta)\r\n", SOUCET1); |
SOUCET1=SOUCET-SOUCET1; |
printf("Soucet - soucet/256: %lX \r\n", SOUCET1); |
LSB=(unsigned int8)SOUCET1; |
printf("LSB: %lX\r\n", LSB); |
//printf("Stav: %X (procenta)\r\n", STAV2); |
*/ |
i2c_start();//blockdata |
I2C_Write(0xAA); |
I2C_write(0x60); |
i2c_start(); |
I2C_Write(0xAA); |
I2C_write(LSB); |
i2c_stop(); |
} |
LSB=LSB+1; |
delay_ms (100); |
} |
} |
/Modules/PowerSupply/LION1CELL01B/SW/PIC16F887/main.bak |
---|
0,0 → 1,43 |
//#include "C:\Users\Honza\Documents\pic\I2C_magnetometr\main.h" |
#include "main.h" |
#define EEPROM_SDA PIN_C4 |
#define EEPROM_SCL PIN_C3 |
#use i2c(master, sda=EEPROM_SDA, scl=EEPROM_SCL) |
#use rs232(baud=9600,parity=N,xmit=PIN_C7,rcv=PIN_C6,bits=8) //rcv TXD xmit RXD |
#include "BQ34Z100.h" |
void main() |
{ |
setup_adc_ports(NO_ANALOGS|VSS_VDD); |
setup_adc(ADC_CLOCK_DIV_2); |
setup_spi(SPI_SS_DISABLED); |
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
setup_timer_1(T1_DISABLED); |
setup_timer_2(T2_DISABLED,0,1); |
setup_ccp1(CCP_OFF); |
setup_comparator(NC_NC_NC_NC);// This device COMP currently not supported by the PICWizard |
printf("Vycitani zakladnich dat z modulu LION1CELL01B \r\n",); |
printf("(c) MLAB 2013 JACHO \r\n",); |
int16 data; |
while(TRUE) |
{ |
data=batintT(); |
printf("Teplota baterie: %Ld (°C)\r\n", data); |
data=batNAP(); |
printf("Napeti clanku: %Ld (mV)\r\n", data); |
data=batPROUD(); |
printf("Proud clankem: %Ld (mA)\r\n", data); |
data=batKAPAKT(); |
printf("Zbyvajici kapacita: %Ld (mAh)\r\n", data); |
data=batKAPMAX(); |
printf("Max. kapacita: %Ld (mAh)\r\n", data); |
data=batSTAV(); |
printf("Stav baterie: %Ld (procenta)\r\n", data); |
delay_ms (2000); |
} |
} |