Problem with comparison.
/Modules/PowerSupply/LION2CELL01D/SW/setguage2cell.py
0,0 → 1,86
#!/usr/bin/python
 
# Setuup of LION2CELL MLAB module
 
import time
import sys
from pymlab import config
 
while True:
#### Sensor Configuration ###########################################
cfg = config.Config(
i2c = {
"port": 0, # I2C bus number
},
 
bus = [
{
"type": "i2chub",
"address": 0x73,
"children": [
{"name": "guage", "type": "lioncell", "channel": 7, },
],
},
],
)
 
 
cfg.initialize()
guage = cfg.get_device("guage")
 
 
guage.WriteFlashByte(48, 0, 21, 0x0D) # Design Capacity 3350 mAh
guage.WriteFlashByte(48, 0, 22, 0x16) #
print "Design Capacity "
guage.WriteFlashByte(48, 0, 23, 0x5E) # Design Energy 24120 mWh
guage.WriteFlashByte(48, 0, 24, 0x38) #
print "Design Energy"
guage.WriteFlashByte(64, 0, 0, 0x9) # External Voltage Measurement
print "External Voltage Measurement"
guage.WriteFlashByte(64, 0, 7, 0x2) # Two Cells
print "Two Cells"
guage.WriteFlashByte(64, 0, 4, 0x74) # 8 LED (1+7), Shift Register
print "LED"
guage.WriteFlashByte(104, 0, 14, 0x28) # Voltage Measurement Range 10240 mV
guage.WriteFlashByte(104, 0, 15, 0x00) #
print "Voltage Measurement Range"
guage.WriteFlashByte(82, 0, 0, 0x0D) # Set initial cell capacity 3350 mAh
guage.WriteFlashByte(82, 0, 1, 0x16) #
print "Initial cell capacity"
guage.WriteFlashByte(83, 0, 0, 0x20) # Set Chem ID
guage.WriteFlashByte(83, 0, 1, 0x17) #
print "Chem ID"
guage.reset() # Reset Guage
print "Reset"
time.sleep(1)
 
flash = guage.ReadFlashBlock(48, 0)
print "48 - ",
print " ".join([hex(i) for i in flash])
flash = guage.ReadFlashBlock(64, 0)
print "64 - ",
print " ".join([hex(i) for i in flash])
flash = guage.ReadFlashBlock(104, 0)
print "104 - ",
print " ".join([hex(i) for i in flash])
 
print "DesCap =", guage.DesignCapacity(), "mAh"
flash = guage.Chemistry()
print "Chemistry = ",
print " ".join([hex(i) for i in flash])
 
try:
while True:
# Battery status readout
print "NominalAvailableCapacity =", guage.NominalAvailableCapacity(), "mAh, FullAvailabeCapacity =", guage.FullAvailabeCapacity(), "mAh, AvailableEnergy =", guage.AvailableEnergy(), "* 10 mWh"
print "Temp =", guage.getTemp(), "degC, RemainCapacity =", guage.getRemainingCapacity(), "mAh, cap =", guage.FullChargeCapacity(), "mAh, U =", guage.Voltage(), "mV, I =", guage.AverageCurrent(), "mA, charge =", guage.StateOfCharge(), "%"
time.sleep(3)
 
except IOError:
err = err + 1
print "IOError"
continue
 
except KeyboardInterrupt:
sys.exit(0)