28,15 → 28,21 |
|
TDC_reset(); |
|
hit1=TDC_MRANGE2_HIT1_START; |
hit2=TDC_MRANGE2_HIT2_2CH1; |
MRange=TDC_MRANGE1; |
hitin1=TDC_HITIN1_2; |
hitin2=TDC_HITIN1_0; |
en_int= 0xFF; //TDC_INT_ALU | TDC_INT_ENDHIT | TDC_INT_TIMEOUT; |
hitin2=TDC_HITIN2_2; |
hit1=TDC_MRANGE1_HIT1_START; |
hit2=TDC_MRANGE1_HIT2_2CH1; |
en_int= (TDC_INT_ALU | TDC_INT_ENDHIT | TDC_INT_TIMEOUT); |
en_err_val=TDC_ERRVAL_EN; |
delval1=0x0; |
delval2=0x0; |
delval3=0x0; |
calibrate=TDC_CALIBRATE_EN; |
disautocal=TDC_AUTOCAL_EN; |
|
firenum=TDC_FIRENUM_2; |
div_fire=TDC_DIV_FIRE_3; |
|
TDC_update_registers(); |
|
43,7 → 49,10 |
output_low(START); |
output_low(STOP1); |
output_low(STOP2); |
|
|
TDC_start_cal_resonator(); |
delay_ms(50); |
printf("calibrate: %LX, %LX, %LX, %LX \r\n", TDC_get_measurement(1), TDC_get_measurement(2), TDC_get_measurement(3), TDC_get_measurement(4)); |
TDC_start_cal(); |
delay_ms(50); |
|
56,28 → 65,43 |
printf("Temp: %f \r\n", temperature); |
delay_ms(50); |
printf("status: %LX \r\n", TDC_get_status()); |
delay_us(10); |
|
TDC_start_cycle(); |
|
delay_us(10); |
output_high(START); |
delay_us(1); |
// delay_us(1); |
output_low(START); |
|
delay_us(500); |
// delay_us(1); |
|
output_high(STOP1); |
delay_us(10); |
// delay_us(10); |
output_low(STOP1); |
delay_us(500); |
output_high(STOP1); |
delay_us(10); |
output_low(STOP1); |
delay_us(500); |
output_high(STOP1); |
delay_us(10); |
output_low(STOP1); |
// delay_us(500); |
// output_high(STOP1); |
// delay_us(10); |
// output_low(STOP1); |
// delay_us(500); |
// output_high(STOP1); |
// delay_us(10); |
// output_low(STOP1); |
|
delay_ms(100); |
output_high(STOP2); |
// delay_us(10); |
output_low(STOP2); |
// delay_us(500); |
output_high(STOP2); |
// delay_us(10); |
output_low(STOP2); |
// delay_us(500); |
output_high(STOP2); |
// delay_us(10); |
output_low(STOP2); |
|
output_low(START); |
|
delay_ms(10); |
printf("status: %LX \r\n", TDC_get_status()); |
delay_ms(50); |
printf("measured: %LX, %LX, %LX, %LX \r\n", TDC_get_measurement(1), TDC_get_measurement(2), TDC_get_measurement(3), TDC_get_measurement(4)); |