Problem with comparison.
/Modules/TDC/GP201A/SW/PICinterface/main.c |
---|
0,0 → 1,121 |
#include "main.h" |
#define VERSION 0.2 |
#define START PIN_D4 |
#define STOP1 PIN_D5 |
#define STOP2 PIN_D6 |
#include "GP2.h" |
#define ONE_WIRE_PIN PIN_E2 |
#include "ds1820.c" |
void main() |
{ |
setup_adc_ports(NO_ANALOGS|VSS_VDD); |
setup_adc(ADC_CLOCK_DIV_2); |
setup_psp(PSP_DISABLED); |
setup_spi(SPI_SS_DISABLED); |
setup_wdt(WDT_OFF); |
setup_timer_0(RTCC_INTERNAL); |
setup_timer_1(T1_DISABLED); |
setup_timer_2(T2_DISABLED,0,1); |
setup_ccp1(CCP_OFF); |
setup_comparator(NC_NC_NC_NC); |
setup_vref(FALSE); |
TDC_reset(); |
output_low(START); |
output_low(STOP1); |
output_low(STOP2); |
delay_ms(50); |
/* |
1 0 0 0 0 ADR2 ADR1 ADR0 Write into address ADR |
1 0 1 1 0 ADR2 ADR1 ADR0 Read from address ADR |
0 1 1 1 0 0 0 0 Init |
0 1 0 1 0 0 0 0 Power On Reset |
0 0 0 0 0 0 0 1 Start_Cycle |
0 0 0 0 0 0 1 0 Start_Temp |
0 0 0 0 0 0 1 1 Start_Cal_Resonator |
0 0 0 0 0 1 0 0 Start_Cal_TDC |
*/ |
int16 ret16; |
int8 ret8; |
TDC_reset(); |
delay_ms(100); |
//----------------------------------------------- Nastaveni registru |
hit1=TDC_MRANGE2_HIT1_START; |
hitin1=TDC_HITIN1_4; |
hitin2=TDC_HITIN2_0; |
en_int= TDC_INT_ALU | TDC_INT_ENDHIT | TDC_INT_TIMEOUT; |
en_err_val=TDC_ERRVAL_EN; |
clkhsdiv=TDC_CLKHSDIV_4; |
delval1=0x0; |
delval2=0x0; |
delval3=0x0; |
TDC_update_registers(); |
while(TRUE) |
{ |
delay_ms(100); |
//----------------------------------------------- Mereni |
TDC_init(); |
delay_ms(50); |
TDC_start_cycle(); |
delay_ms(200); |
output_high(STOP2); // Merime jenom jednim kanalem (druhy zrejme musi byt v H) |
output_high(START); |
output_low(START); |
delay_us(150); |
output_high(STOP1); |
output_low(STOP1); |
delay_us(1); |
output_high(STOP1); |
output_low(STOP1); |
delay_us(10); |
output_high(STOP1); |
output_low(STOP1); |
delay_us(1); |
//----------------------------------------------- Pocitani |
printf("Time: %3.7f %3.7f %3.7f ", TDC_mrange2_get_time(1), TDC_mrange2_get_time(2), TDC_mrange2_get_time(3)); |
output_low(TDC_ENABLE); //status register |
ret8=0; |
ret8=(0b1011<<4)|4; |
spi_xfer(TDC_stream,ret8,8); |
ret16=spi_xfer(TDC_stream,0,16); |
output_high(TDC_ENABLE); |
printf("[%Lu %Lu %Lu %Lu %Lu %Lu %Lu]\r\n", (1&(ret16)>>12), (1&(ret16)>>11), (1&(ret16)>>10), 1&(ret16)>>9, 7&(ret16)>>6, 7&(ret16)>>3, 7&TDC_get_status()); |
TDC_start_temp(); |
output_low(TDC_ENABLE); //status register |
ret8=0; |
ret8=(0b1011<<4)|4; |
spi_xfer(TDC_stream,ret8,8); |
ret16=spi_xfer(TDC_stream,0,16); |
output_high(TDC_ENABLE); |
printf("Temp: [%Lu %Lu %Lu %Lu %Lu %Lu %Lu] ", (1&(ret16)>>12), (1&(ret16)>>11), (1&(ret16)>>10), 1&(ret16)>>9, 7&(ret16)>>6, 7&(ret16)>>3, 7&TDC_get_status()); |
printf(" %LX %LX %LX %LX \r\n", TDC_get_measurement(1), TDC_get_measurement(2), TDC_get_measurement(3), TDC_get_measurement(4)); |
} |
} |