| /Modules/CommRF/LNA01A/PrjInfo.txt |
|---|
| 1,15 → 1,13 |
| [InfoShortDescription.en] |
| Low noise antenna preamplifier |
| Simple IR reflexive sensor. |
| [InfoShortDescription.cs] |
| Nízkošumový anténní zesilovač. |
| Jednoduche reflexivni cidlo. |
| [InfoLongDescription.en] |
| Very low noise <0.8dB band pass amplifier to multi frequency bands. |
| [InfoLongDescription.cs] |
| Nízkošumový <0.8dB pásmový zesilovač, pro různá frekvenční pásma. |
| Čidlo obsahuje pouze reflexní optron s odporovým trimrem a slouží k rozlišování tmavého a světlého povrchu. Dá se použít jak pro detekci čáry pro čárového robota tak i pro snímání otáčení pohonných kol. |
| [End] |
| [End] |
| /Modules/TDC/GP201A/TODO.txt |
|---|
| File deleted |
| /Modules/Universal/UNIATMEGA8TQFP01A/PCB/kicad/universal1.pro |
|---|
| 1,5 → 1,5 |
| update=So 20. srpen 2011, 16:34:15 CEST |
| last_client=pcbnew |
| update=Fri Aug 19 21:57:11 2011 |
| last_client=eeschema |
| [general] |
| version=1 |
| [cvpcb] |
| 7,6 → 7,36 |
| NetIExt=net |
| [cvpcb/libraries] |
| EquName1=devcms |
| [pcbnew] |
| version=1 |
| PadDrlX=320 |
| PadDimH=800 |
| PadDimV=800 |
| BoardThickness=630 |
| SgPcb45=1 |
| TxtPcbV=800 |
| TxtPcbH=600 |
| TxtModV=600 |
| TxtModH=600 |
| TxtModW=120 |
| VEgarde=100 |
| DrawLar=150 |
| EdgeLar=150 |
| TxtLar=120 |
| MSegLar=150 |
| LastNetListRead= |
| [pcbnew/libraries] |
| LibDir= |
| LibName1=sockets |
| LibName2=connect |
| LibName3=discret |
| LibName4=pin_array |
| LibName5=divers |
| LibName6=libcms |
| LibName7=display |
| LibName8=valves |
| LibName9=led |
| LibName10=dip_sockets |
| [eeschema] |
| version=1 |
| LibDir=../UniversalModule1 |
| 77,33 → 107,3 |
| LibName32=DIL8 |
| LibName33=DIL16 |
| LibName34=DIL20 |
| [pcbnew] |
| version=1 |
| PadDrlX=320 |
| PadDimH=800 |
| PadDimV=800 |
| BoardThickness=630 |
| SgPcb45=1 |
| TxtPcbV=800 |
| TxtPcbH=600 |
| TxtModV=600 |
| TxtModH=600 |
| TxtModW=120 |
| VEgarde=100 |
| DrawLar=150 |
| EdgeLar=150 |
| TxtLar=120 |
| MSegLar=150 |
| LastNetListRead= |
| [pcbnew/libraries] |
| LibDir= |
| LibName1=sockets |
| LibName2=connect |
| LibName3=discret |
| LibName4=pin_array |
| LibName5=divers |
| LibName6=libcms |
| LibName7=display |
| LibName8=valves |
| LibName9=led |
| LibName10=dip_sockets |
| /Designs/duckweed_collector/PrjInfo.txt |
|---|
| File deleted |
| /Designs/LABduino/SW/bootloader/flash.sh |
|---|
| 1,7 → 1,7 |
| # Linux Shell Script |
| # ATprogISPUSB02A fash script |
| # Uses DAPA (Direct Parallel Access) Programmer |
| read -p "WARNING: This procedure enables external clock. Make sure if a 16MHz crystal is installed on MCU module with ATmega328 and connect the MCU module to the programmer ATprogISPUSB02A" |
| read -p "WARNING: This procedure enables external clock. Make sure if a 16MHz crystal is soldered and connect the MCU module to the programmer ATprogISPUSB02A" |
| avrdude -F -p atmega328P -P /dev/ttyUSB0 -c stk500v2 -B 50 -v -U efuse:w:0x05:m -U lfuse:w:0xff:m -U hfuse:w:0xda:m |
| avrdude -F -p atmega328P -P /dev/ttyUSB0 -c stk500v2 -B 50 -U flash:w:ATmegaBOOT_168_atmega328.hex:a |
| echo "If none errors above - Please connect the USB232R01B module to bootload the LABduino via Arduino software." |