| /Designs/Laboratory_instruments/High_voltage_power_supply/SW/VN/vn.c |
|---|
| 0,0 → 1,82 |
| #include "D:\PIC\VN\vn.h" |
| //#define MAXDUTY (int16)160 // 50 kHz |
| #define MAXDUTY (int16)400 // 20 kHz |
| //#define MAXDUTY (int16)800 // 10 kHz |
| #define HALFDUTY (int16)MAXDUTY/2 |
| //#define DIVISOR 199 // 10 kHz |
| #define DIVISOR 99 // 20 kHz |
| //#define DIVISOR 39 // 50 kHz |
| #define regreseM (2.02) |
| #define regreseN (-451) |
| void main() |
| { |
| setup_adc_ports(sAN0|VSS_VDD); |
| setup_adc(ADC_CLOCK_DIV_2); |
| setup_spi(SPI_SS_DISABLED); |
| setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| setup_timer_1(T1_DISABLED); |
| setup_timer_2(T2_DIV_BY_1,DIVISOR,1); |
| setup_ccp1(CCP_PWM); |
| setup_ccp2(CCP_PWM); |
| set_pwm1_duty(HALFDUTY); |
| set_pwm2_duty(MAXDUTY); |
| setup_comparator(NC_NC_NC_NC); |
| setup_oscillator(OSC_8MHZ); |
| set_adc_channel(0); |
| delay_ms(500); |
| unsigned int16 reg; |
| float given; |
| printf("Cvak\r\n"); |
| reg=400; |
| given=regreseM*reg+regreseN; |
| while(true) |
| { |
| unsigned int16 value; |
| value = read_adc(); |
| if(kbhit()) |
| { |
| char c; |
| set_pwm2_duty((int16)MAXDUTY); |
| c=getc(); |
| if(c=='u') |
| { |
| if (reg<600) reg++; |
| printf("up*"); |
| } |
| if(c=='d') |
| { |
| if (reg>250) reg--; |
| printf("down*"); |
| } |
| if((c>='a')&&(c<='z')) |
| { |
| given=regreseM*reg+regreseN; |
| printf("reg: %Lu\r\n",reg); |
| } |
| } |
| if (value >= given) |
| { |
| set_pwm2_duty((int16)MAXDUTY); |
| } |
| else |
| { |
| set_pwm2_duty((int16)255); |
| } |
| delay_us(200); |
| } |
| } |
| /Designs/Laboratory_instruments/High_voltage_power_supply/SW/VN/vn.h |
|---|
| 0,0 → 1,20 |
| #include <16F887.h> |
| #device adc=10 |
| #FUSES NOWDT //No Watch Dog Timer |
| #FUSES INTRC //Internal RC Osc |
| #FUSES NOPUT //No Power Up Timer |
| #FUSES MCLR //Master Clear pin enabled |
| #FUSES NOPROTECT //Code not protected from reading |
| #FUSES NOCPD //No EE protection |
| #FUSES NOBROWNOUT //No brownout reset |
| #FUSES IESO //Internal External Switch Over mode enabled |
| #FUSES FCMEN //Fail-safe clock monitor enabled |
| #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
| #FUSES NODEBUG //No Debug mode for ICD |
| #FUSES NOWRT //Program memory not write protected |
| #FUSES BORV40 //Brownout reset at 4.0V |
| #use delay(clock=8000000) |
| #use rs232(baud=1200,parity=N,xmit=PIN_B7,rcv=PIN_B6,bits=8,stop=1) |
| /Designs/Laboratory_instruments/High_voltage_power_supply/SW/VN/vn.pjt |
|---|
| 0,0 → 1,26 |
| [PROJECT] |
| Target=D:\PIC\VN\vn.hex |
| Development_Mode= |
| Processor_Text=PIC16F887 |
| ToolSuite=CCS |
| Processor=0x887F |
| [D:\PIC\VN\vn] |
| Type=4 |
| Path= |
| FileList= |
| BuildTool= |
| OptionString= |
| AdditionalOptionString= |
| [mru-list] |
| 1=D:\PIC\VN\vn.c |
| [Windows] |
| 0=0000 %S 0 0 796 451 3 0 |
| [Units] |
| Link=0 |
| Count=1 |
| 1=D:\PIC\VN\vn |
| [Opened Files] |
| 1=vn.c |
| 2=vn.h |
| 3=C:\Program Files (x86)\PICC\devices\16F887.h |
| 4= |